rfkill.txt 5.04 KB
Newer Older
1
===============================
Johannes Berg's avatar
Johannes Berg committed
2 3
rfkill - RF kill switch support
===============================
4 5


6 7
.. contents::
   :depth: 2
8

9 10
Introduction
============
11

Johannes Berg's avatar
Johannes Berg committed
12 13 14
The rfkill subsystem provides a generic interface to disabling any radio
transmitter in the system. When a transmitter is blocked, it shall not
radiate any power.
15

Johannes Berg's avatar
Johannes Berg committed
16 17 18 19
The subsystem also provides the ability to react on button presses and
disable all transmitters of a certain type (or all). This is intended for
situations where transmitters need to be turned off, for example on
aircraft.
20

Johannes Berg's avatar
Johannes Berg committed
21 22 23
The rfkill subsystem has a concept of "hard" and "soft" block, which
differ little in their meaning (block == transmitters off) but rather in
whether they can be changed or not:
24 25 26 27 28 29 30

 - hard block
	read-only radio block that cannot be overridden by software

 - soft block
	writable radio block (need not be readable) that is set by
        the system software.
31

32
The rfkill subsystem has two parameters, rfkill.default_state and
33 34
rfkill.master_switch_mode, which are documented in
admin-guide/kernel-parameters.rst.
35

36

37 38
Implementation details
======================
39

Johannes Berg's avatar
Johannes Berg committed
40
The rfkill subsystem is composed of three main components:
41

Johannes Berg's avatar
Johannes Berg committed
42 43 44 45
 * the rfkill core,
 * the deprecated rfkill-input module (an input layer handler, being
   replaced by userspace policy code) and
 * the rfkill drivers.
46

Johannes Berg's avatar
Johannes Berg committed
47 48 49 50
The rfkill core provides API for kernel drivers to register their radio
transmitter with the kernel, methods for turning it on and off and, letting
the system know about hardware-disabled states that may be implemented on
the device.
51

Johannes Berg's avatar
Johannes Berg committed
52 53 54
The rfkill core code also notifies userspace of state changes, and provides
ways for userspace to query the current states. See the "Userspace support"
section below.
55

Johannes Berg's avatar
Johannes Berg committed
56
When the device is hard-blocked (either by a call to rfkill_set_hw_state()
Johannes Berg's avatar
Johannes Berg committed
57 58 59 60 61 62
or from query_hw_block) set_block() will be invoked for additional software
block, but drivers can ignore the method call since they can use the return
value of the function rfkill_set_hw_state() to sync the software state
instead of keeping track of calls to set_block(). In fact, drivers should
use the return value of rfkill_set_hw_state() unless the hardware actually
keeps track of soft and hard block separately.
63 64


65 66
Kernel API
==========
67 68


Johannes Berg's avatar
Johannes Berg committed
69
Drivers for radio transmitters normally implement an rfkill driver.
70

Johannes Berg's avatar
Johannes Berg committed
71 72
Platform drivers might implement input devices if the rfkill button is just
that, a button. If that button influences the hardware then you need to
Johannes Berg's avatar
Johannes Berg committed
73
implement an rfkill driver instead. This also applies if the platform provides
Johannes Berg's avatar
Johannes Berg committed
74
a way to turn on/off the transmitter(s).
75

Johannes Berg's avatar
Johannes Berg committed
76 77 78
For some platforms, it is possible that the hardware state changes during
suspend/hibernation, in which case it will be necessary to update the rfkill
core with the current state is at resume time.
79

80
To create an rfkill driver, driver's Kconfig needs to have::
81

Johannes Berg's avatar
Johannes Berg committed
82
	depends on RFKILL || !RFKILL
83

Johannes Berg's avatar
Johannes Berg committed
84
to ensure the driver cannot be built-in when rfkill is modular. The !RFKILL
85
case allows the driver to be built when rfkill is not configured, which
Johannes Berg's avatar
Johannes Berg committed
86 87
case all rfkill API can still be used but will be provided by static inlines
which compile to almost nothing.
88

Johannes Berg's avatar
Johannes Berg committed
89 90 91 92
Calling rfkill_set_hw_state() when a state change happens is required from
rfkill drivers that control devices that can be hard-blocked unless they also
assign the poll_hw_block() callback (then the rfkill core will poll the
device). Don't do this unless you cannot get the event in any other way.
93

94 95
RFKill provides per-switch LED triggers, which can be used to drive LEDs
according to the switch state (LED_FULL when blocked, LED_OFF otherwise).
96 97


98 99
Userspace support
=================
100

Johannes Berg's avatar
Johannes Berg committed
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115
The recommended userspace interface to use is /dev/rfkill, which is a misc
character device that allows userspace to obtain and set the state of rfkill
devices and sets of devices. It also notifies userspace about device addition
and removal. The API is a simple read/write API that is defined in
linux/rfkill.h, with one ioctl that allows turning off the deprecated input
handler in the kernel for the transition period.

Except for the one ioctl, communication with the kernel is done via read()
and write() of instances of 'struct rfkill_event'. In this structure, the
soft and hard block are properly separated (unlike sysfs, see below) and
userspace is able to get a consistent snapshot of all rfkill devices in the
system. Also, it is possible to switch all rfkill drivers (or all drivers of
a specified type) into a state which also updates the default state for
hotplugged devices.

116 117 118 119 120 121 122 123
After an application opens /dev/rfkill, it can read the current state of all
devices. Changes can be either obtained by either polling the descriptor for
hotplug or state change events or by listening for uevents emitted by the
rfkill core framework.

Additionally, each rfkill device is registered in sysfs and emits uevents.

rfkill devices issue uevents (with an action of "change"), with the following
124
environment variables set::
Johannes Berg's avatar
Johannes Berg committed
125

126 127 128
	RFKILL_NAME
	RFKILL_STATE
	RFKILL_TYPE
Johannes Berg's avatar
Johannes Berg committed
129 130 131

The contents of these variables corresponds to the "name", "state" and
"type" sysfs files explained above.
132 133


Paul Bolle's avatar
Paul Bolle committed
134
For further details consult Documentation/ABI/stable/sysfs-class-rfkill.