Commit 1c59d045 authored by Masahiro Yamada's avatar Masahiro Yamada Committed by Linus Walleij

dt-bindings: gpio: uniphier: add UniPhier GPIO binding

This GPIO controller is used on UniPhier SoC family.

The vendor specific property "socionext,interrupt-ranges" is for
specifying interrupt mapping to the parent interrupt controller
because the mapping is not contiguous.  It works like "ranges",
but transforms "interrupts" instead of "reg".
Signed-off-by: Masahiro Yamada's avatarMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent 2cbfca66
UniPhier GPIO controller
Required properties:
- compatible: Should be "socionext,uniphier-gpio".
- reg: Specifies offset and length of the register set for the device.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be 2. The first cell is the pin number and the second
cell is used to specify optional parameters.
- interrupt-parent: Specifies the parent interrupt controller.
- interrupt-controller: Marks the device node as an interrupt controller.
- #interrupt-cells: Should be 2. The first cell defines the interrupt number.
The second cell bits[3:0] is used to specify trigger type as follows:
1 = low-to-high edge triggered
2 = high-to-low edge triggered
4 = active high level-sensitive
8 = active low level-sensitive
Valid combinations are 1, 2, 3, 4, 8.
- ngpios: Specifies the number of GPIO lines.
- gpio-ranges: Mapping to pin controller pins (as described in gpio.txt)
- socionext,interrupt-ranges: Specifies an interrupt number mapping between
this GPIO controller and its interrupt parent, in the form of arbitrary
number of <child-interrupt-base parent-interrupt-base length> triplets.
Optional properties:
- gpio-ranges-group-names: Used for named gpio ranges (as described in gpio.txt)
Example:
gpio: gpio@55000000 {
compatible = "socionext,uniphier-gpio";
reg = <0x55000000 0x200>;
interrupt-parent = <&aidet>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pinctrl 0 0 0>;
gpio-ranges-group-names = "gpio_range";
ngpios = <248>;
socionext,interrupt-ranges = <0 48 16>, <16 154 5>, <21 217 3>;
};
Consumer Example:
sdhci0_pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio UNIPHIER_GPIO_PORT(29, 4) GPIO_ACTIVE_LOW>;
};
Please note UNIPHIER_GPIO_PORT(29, 4) represents PORT294 in the SoC document.
Unfortunately, only the one's place is octal in the port numbering. (That is,
PORT 8, 9, 18, 19, 28, 29, ... are missing.) UNIPHIER_GPIO_PORT() is a helper
macro to calculate 29 * 8 + 4.
......@@ -2017,6 +2017,7 @@ M: Masahiro Yamada <yamada.masahiro@socionext.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
T: git git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier.git
S: Maintained
F: Documentation/devicetree/bindings/gpio/gpio-uniphier.txt
F: arch/arm/boot/dts/uniphier*
F: arch/arm/include/asm/hardware/cache-uniphier.h
F: arch/arm/mach-uniphier/
......
/*
* Copyright (C) 2017 Socionext Inc.
* Author: Masahiro Yamada <yamada.masahiro@socionext.com>
*/
#ifndef _DT_BINDINGS_GPIO_UNIPHIER_H
#define _DT_BINDINGS_GPIO_UNIPHIER_H
#define UNIPHIER_GPIO_LINES_PER_BANK 8
#define UNIPHIER_GPIO_IRQ_OFFSET ((UNIPHIER_GPIO_LINES_PER_BANK) * 15)
#define UNIPHIER_GPIO_PORT(bank, line) \
((UNIPHIER_GPIO_LINES_PER_BANK) * (bank) + (line))
#define UNIPHIER_GPIO_IRQ(n) ((UNIPHIER_GPIO_IRQ_OFFSET) + (n))
#endif /* _DT_BINDINGS_GPIO_UNIPHIER_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment