Commit 0a276d16 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...
parents 25aa6a7a 08298f06
......@@ -57,6 +57,7 @@ config SH_7724_SOLUTION_ENGINE
depends on CPU_SUBTYPE_SH7724
select ARCH_REQUIRE_GPIOLIB
select SND_SOC_AK4642 if SND_SIMPLE_CARD
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Select 7724 SolutionEngine if configuring for a Hitachi SH7724
evaluation board.
......@@ -140,6 +141,7 @@ config SH_RSK
bool "Renesas Starter Kit"
depends on CPU_SUBTYPE_SH7201 || CPU_SUBTYPE_SH7203 || \
CPU_SUBTYPE_SH7264 || CPU_SUBTYPE_SH7269
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Select this option if configuring for any of the RSK+ MCU
evaluation platforms.
......@@ -159,6 +161,7 @@ config SH_SDK7786
select NO_IOPORT if !PCI
select ARCH_WANT_OPTIONAL_GPIOLIB
select HAVE_SRAM_POOL
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Select SDK7786 if configuring for a Renesas Technology Europe
SH7786-65nm board.
......@@ -173,6 +176,7 @@ config SH_SH7757LCR
bool "SH7757LCR"
depends on CPU_SUBTYPE_SH7757
select ARCH_REQUIRE_GPIOLIB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
config SH_SH7785LCR
bool "SH7785LCR"
......@@ -206,6 +210,7 @@ config SH_MIGOR
bool "Migo-R"
depends on CPU_SUBTYPE_SH7722
select ARCH_REQUIRE_GPIOLIB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Select Migo-R if configuring for the SH7722 Migo-R platform
by Renesas System Solutions Asia Pte. Ltd.
......@@ -214,6 +219,7 @@ config SH_AP325RXA
bool "AP-325RXA"
depends on CPU_SUBTYPE_SH7723
select ARCH_REQUIRE_GPIOLIB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Renesas "AP-325RXA" support.
Compatible with ALGO SYSTEM CO.,LTD. "AP-320A"
......@@ -222,6 +228,7 @@ config SH_KFR2R09
bool "KFR2R09"
depends on CPU_SUBTYPE_SH7724
select ARCH_REQUIRE_GPIOLIB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
"Kit For R2R for 2009" support.
......@@ -230,6 +237,7 @@ config SH_ECOVEC
depends on CPU_SUBTYPE_SH7724
select ARCH_REQUIRE_GPIOLIB
select SND_SOC_DA7210 if SND_SIMPLE_CARD
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Renesas "R0P7724LC0011/21RL (EcoVec)" support.
......@@ -305,6 +313,7 @@ config SH_MAGIC_PANEL_R2
bool "Magic Panel R2"
depends on CPU_SUBTYPE_SH7720
select ARCH_REQUIRE_GPIOLIB
select REGULATOR_FIXED_VOLTAGE if REGULATOR
help
Select Magic Panel R2 if configuring for Magic Panel R2.
......@@ -316,6 +325,7 @@ config SH_CAYMAN
config SH_POLARIS
bool "SMSC Polaris"
select CPU_HAS_IPR_IRQ
select REGULATOR_FIXED_VOLTAGE if REGULATOR
depends on CPU_SUBTYPE_SH7709
help
Select if configuring for an SMSC Polaris development board
......@@ -323,6 +333,7 @@ config SH_POLARIS
config SH_SH2007
bool "SH-2007 board"
select NO_IOPORT
select REGULATOR_FIXED_VOLTAGE if REGULATOR
depends on CPU_SUBTYPE_SH7780
help
SH-2007 is a single-board computer based around SH7780 chip
......@@ -334,6 +345,7 @@ config SH_SH2007
config SH_APSH4A3A
bool "AP-SH4A-3A"
select SH_ALPHA_BOARD
select REGULATOR_FIXED_VOLTAGE if REGULATOR
depends on CPU_SUBTYPE_SH7785
help
Select AP-SH4A-3A if configuring for an ALPHAPROJECT AP-SH4A-3A.
......@@ -342,6 +354,7 @@ config SH_APSH4AD0A
bool "AP-SH4AD-0A"
select SH_ALPHA_BOARD
select SYS_SUPPORTS_PCI
select REGULATOR_FIXED_VOLTAGE if REGULATOR
depends on CPU_SUBTYPE_SH7786
help
Select AP-SH4AD-0A if configuring for an ALPHAPROJECT AP-SH4AD-0A.
......
......@@ -13,6 +13,8 @@
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/mtd/physmap.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/irq.h>
#include <linux/clk.h>
......@@ -66,6 +68,12 @@ static struct platform_device nor_flash_device = {
.resource = nor_flash_resources,
};
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static struct resource smsc911x_resources[] = {
[0] = {
.name = "smsc911x-memory",
......@@ -105,6 +113,8 @@ static struct platform_device *apsh4a3a_devices[] __initdata = {
static int __init apsh4a3a_devices_setup(void)
{
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
return platform_add_devices(apsh4a3a_devices,
ARRAY_SIZE(apsh4a3a_devices));
}
......
......@@ -12,12 +12,20 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/irq.h>
#include <linux/clk.h>
#include <asm/machvec.h>
#include <asm/sizes.h>
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static struct resource smsc911x_resources[] = {
[0] = {
.name = "smsc911x-memory",
......@@ -56,6 +64,8 @@ static struct platform_device *apsh4ad0a_devices[] __initdata = {
static int __init apsh4ad0a_devices_setup(void)
{
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
return platform_add_devices(apsh4ad0a_devices,
ARRAY_SIZE(apsh4ad0a_devices));
}
......
......@@ -14,6 +14,8 @@
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
......@@ -24,6 +26,12 @@
#include <asm/heartbeat.h>
#include <cpu/sh7720.h>
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
#define LAN9115_READY (__raw_readl(0xA8000084UL) & 0x00000001UL)
/* Wait until reset finished. Timeout is 100ms. */
......@@ -348,6 +356,8 @@ static struct platform_device *mpr2_devices[] __initdata = {
static int __init mpr2_devices_setup(void)
{
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
return platform_add_devices(mpr2_devices, ARRAY_SIZE(mpr2_devices));
}
device_initcall(mpr2_devices_setup);
......
......@@ -9,6 +9,8 @@
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/io.h>
#include <asm/irq.h>
......@@ -22,6 +24,12 @@
#define AREA5_WAIT_CTRL (0x1C00)
#define WAIT_STATES_10 (0x7)
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
};
static struct resource smsc911x_resources[] = {
[0] = {
.name = "smsc911x-memory",
......@@ -88,6 +96,8 @@ static int __init polaris_initialise(void)
printk(KERN_INFO "Configuring Polaris external bus\n");
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
/* Configure area 5 with 2 wait states */
wcr = __raw_readw(WCR2);
wcr &= (~AREA5_WAIT_CTRL);
......
......@@ -6,6 +6,8 @@
*/
#include <linux/init.h>
#include <linux/irq.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/platform_device.h>
#include <linux/ata_platform.h>
......@@ -13,6 +15,14 @@
#include <asm/machvec.h>
#include <mach/sh2007.h>
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
};
struct smsc911x_platform_config smc911x_info = {
.flags = SMSC911X_USE_32BIT,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
......@@ -98,6 +108,8 @@ static struct platform_device *sh2007_devices[] __initdata = {
static int __init sh2007_io_init(void)
{
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
platform_add_devices(sh2007_devices, ARRAY_SIZE(sh2007_devices));
return 0;
}
......
......@@ -12,6 +12,8 @@
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/spi/spi.h>
#include <linux/spi/flash.h>
#include <linux/io.h>
......@@ -199,6 +201,15 @@ static struct platform_device sh7757_eth_giga1_device = {
},
};
/* Fixed 3.3V regulator to be used by SDHI0, MMCIF */
static struct regulator_consumer_supply fixed3v3_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
};
/* SH_MMCIF */
static struct resource sh_mmcif_resources[] = {
[0] = {
......@@ -329,6 +340,9 @@ static struct spi_board_info spi_board_info[] = {
static int __init sh7757lcr_devices_setup(void)
{
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
/* RGMII (PTA) */
gpio_request(GPIO_FN_ET0_MDC, NULL);
gpio_request(GPIO_FN_ET0_MDIO, NULL);
......
......@@ -20,6 +20,8 @@
#include <linux/mtd/sh_flctl.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/gpio.h>
#include <linux/videodev2.h>
......@@ -34,6 +36,12 @@
#include <asm/suspend.h>
#include <cpu/sh7723.h>
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static struct smsc911x_platform_config smsc911x_config = {
.phy_interface = PHY_INTERFACE_MODE_MII,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
......@@ -423,6 +431,15 @@ static struct platform_device ceu_device = {
},
};
/* Fixed 3.3V regulators to be used by SDHI0, SDHI1 */
static struct regulator_consumer_supply fixed3v3_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
};
static struct resource sdhi0_cn3_resources[] = {
[0] = {
.name = "SDHI0",
......@@ -544,6 +561,10 @@ static int __init ap325rxa_devices_setup(void)
&ap325rxa_sdram_leave_start,
&ap325rxa_sdram_leave_end);
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
/* LD3 and LD4 LEDs */
gpio_request(GPIO_PTX5, NULL); /* RUN */
gpio_direction_output(GPIO_PTX5, 1);
......
......@@ -19,6 +19,8 @@
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/delay.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/usb/r8a66597.h>
#include <linux/usb/renesas_usbhs.h>
#include <linux/i2c.h>
......@@ -242,9 +244,17 @@ static int usbhs_get_id(struct platform_device *pdev)
return gpio_get_value(GPIO_PTB3);
}
static void usbhs_phy_reset(struct platform_device *pdev)
{
/* enable vbus if HOST */
if (!gpio_get_value(GPIO_PTB3))
gpio_set_value(GPIO_PTB5, 1);
}
static struct renesas_usbhs_platform_info usbhs_info = {
.platform_callback = {
.get_id = usbhs_get_id,
.phy_reset = usbhs_phy_reset,
},
.driver_param = {
.buswait_bwait = 4,
......@@ -518,10 +528,86 @@ static struct i2c_board_info ts_i2c_clients = {
.irq = IRQ0,
};
static struct regulator_consumer_supply cn12_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
};
static struct regulator_init_data cn12_power_init_data = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(cn12_power_consumers),
.consumer_supplies = cn12_power_consumers,
};
static struct fixed_voltage_config cn12_power_info = {
.supply_name = "CN12 SD/MMC Vdd",
.microvolts = 3300000,
.gpio = GPIO_PTB7,
.enable_high = 1,
.init_data = &cn12_power_init_data,
};
static struct platform_device cn12_power = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
.platform_data = &cn12_power_info,
},
};
#if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
/* SDHI0 */
static struct regulator_consumer_supply sdhi0_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
};
static struct regulator_init_data sdhi0_power_init_data = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(sdhi0_power_consumers),
.consumer_supplies = sdhi0_power_consumers,
};
static struct fixed_voltage_config sdhi0_power_info = {
.supply_name = "CN11 SD/MMC Vdd",
.microvolts = 3300000,
.gpio = GPIO_PTB6,
.enable_high = 1,
.init_data = &sdhi0_power_init_data,
};
static struct platform_device sdhi0_power = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &sdhi0_power_info,
},
};
static void sdhi0_set_pwr(struct platform_device *pdev, int state)
{
static int power_gpio = -EINVAL;
if (power_gpio < 0) {
int ret = gpio_request(GPIO_PTB6, NULL);
if (!ret) {
power_gpio = GPIO_PTB6;
gpio_direction_output(power_gpio, 0);
}
}
/*
* Toggle the GPIO regardless, whether we managed to grab it above or
* the fixed regulator driver did.
*/
gpio_set_value(GPIO_PTB6, state);
}
......@@ -562,13 +648,27 @@ static struct platform_device sdhi0_device = {
},
};
#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
/* SDHI1 */
static void sdhi1_set_pwr(struct platform_device *pdev, int state)
static void cn12_set_pwr(struct platform_device *pdev, int state)
{
static int power_gpio = -EINVAL;
if (power_gpio < 0) {
int ret = gpio_request(GPIO_PTB7, NULL);
if (!ret) {
power_gpio = GPIO_PTB7;
gpio_direction_output(power_gpio, 0);
}
}
/*
* Toggle the GPIO regardless, whether we managed to grab it above or
* the fixed regulator driver did.
*/
gpio_set_value(GPIO_PTB7, state);
}
#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
/* SDHI1 */
static int sdhi1_get_cd(struct platform_device *pdev)
{
return !gpio_get_value(GPIO_PTW7);
......@@ -579,7 +679,7 @@ static struct sh_mobile_sdhi_info sdhi1_info = {
.dma_slave_rx = SHDMA_SLAVE_SDHI1_RX,
.tmio_caps = MMC_CAP_SDIO_IRQ | MMC_CAP_POWER_OFF_CARD |
MMC_CAP_NEEDS_POLL,
.set_pwr = sdhi1_set_pwr,
.set_pwr = cn12_set_pwr,
.get_cd = sdhi1_get_cd,
};
......@@ -899,14 +999,9 @@ static struct platform_device vou_device = {
#if defined(CONFIG_MMC_SH_MMCIF) || defined(CONFIG_MMC_SH_MMCIF_MODULE)
/* SH_MMCIF */
static void mmcif_set_pwr(struct platform_device *pdev, int state)
{
gpio_set_value(GPIO_PTB7, state);
}
static void mmcif_down_pwr(struct platform_device *pdev)
{
gpio_set_value(GPIO_PTB7, 0);
cn12_set_pwr(pdev, 0);
}
static struct resource sh_mmcif_resources[] = {
......@@ -929,7 +1024,7 @@ static struct resource sh_mmcif_resources[] = {
};
static struct sh_mmcif_plat_data sh_mmcif_plat = {
.set_pwr = mmcif_set_pwr,
.set_pwr = cn12_set_pwr,
.down_pwr = mmcif_down_pwr,
.sup_pclk = 0, /* SH7724: Max Pclk/2 */
.caps = MMC_CAP_4_BIT_DATA |
......@@ -960,7 +1055,9 @@ static struct platform_device *ecovec_devices[] __initdata = {
&ceu0_device,
&ceu1_device,
&keysc_device,
&cn12_power,
#if defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
&sdhi0_power,
&sdhi0_device,
#if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
&sdhi1_device,
......@@ -1258,8 +1355,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_SDHI0D2, NULL);
gpio_request(GPIO_FN_SDHI0D1, NULL);
gpio_request(GPIO_FN_SDHI0D0, NULL);
gpio_request(GPIO_PTB6, NULL);
gpio_direction_output(GPIO_PTB6, 0);
#else
/* enable MSIOF0 on CN11 (needs DS2.4 set to OFF) */
gpio_request(GPIO_FN_MSIOF0_TXD, NULL);
......@@ -1288,8 +1383,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_MMC_D0, NULL);
gpio_request(GPIO_FN_MMC_CLK, NULL);
gpio_request(GPIO_FN_MMC_CMD, NULL);
gpio_request(GPIO_PTB7, NULL);
gpio_direction_output(GPIO_PTB7, 0);
cn12_enabled = true;
#elif defined(CONFIG_MMC_SDHI) || defined(CONFIG_MMC_SDHI_MODULE)
......@@ -1301,8 +1394,6 @@ static int __init arch_setup(void)
gpio_request(GPIO_FN_SDHI1D2, NULL);
gpio_request(GPIO_FN_SDHI1D1, NULL);
gpio_request(GPIO_FN_SDHI1D0, NULL);
gpio_request(GPIO_PTB7, NULL);
gpio_direction_output(GPIO_PTB7, 0);
/* Card-detect, used on CN12 with SDHI1 */
gpio_request(GPIO_PTW7, NULL);
......
......@@ -21,6 +21,8 @@
#include <linux/input.h>
#include <linux/input/sh_keysc.h>
#include <linux/i2c.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/usb/r8a66597.h>
#include <linux/videodev2.h>
#include <linux/sh_intc.h>
......@@ -341,6 +343,13 @@ static struct platform_device kfr2r09_camera = {
},
};
/* Fixed 3.3V regulator to be used by SDHI0 */
static struct regulator_consumer_supply fixed3v3_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
};
static struct resource kfr2r09_sh_sdhi0_resources[] = {
[0] = {
.name = "SDHI0",
......@@ -523,6 +532,9 @@ static int __init kfr2r09_devices_setup(void)
&kfr2r09_sdram_leave_start,
&kfr2r09_sdram_leave_end);
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
/* enable SCIF1 serial port for YC401 console support */
gpio_request(GPIO_FN_SCIF1_RXD, NULL);
gpio_request(GPIO_FN_SCIF1_TXD, NULL);
......
......@@ -17,6 +17,8 @@
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand.h>
#include <linux/i2c.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smc91x.h>
#include <linux/delay.h>
#include <linux/clk.h>
......@@ -386,6 +388,13 @@ static struct platform_device migor_ceu_device = {
},
};
/* Fixed 3.3V regulator to be used by SDHI0 */
static struct regulator_consumer_supply fixed3v3_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
};
static struct resource sdhi_cn9_resources[] = {
[0] = {
.name = "SDHI",
......@@ -498,6 +507,10 @@ static int __init migor_devices_setup(void)
&migor_sdram_enter_end,
&migor_sdram_leave_start,
&migor_sdram_leave_end);
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
/* Let D11 LED show STATUS0 */
gpio_request(GPIO_FN_STATUS0, NULL);
......
......@@ -16,9 +16,17 @@
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/map.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <asm/machvec.h>
#include <asm/io.h>
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static const char *part_probes[] = { "cmdlinepart", NULL };
static struct mtd_partition rsk_partitions[] = {
......@@ -67,6 +75,8 @@ static struct platform_device *rsk_devices[] __initdata = {
static int __init rsk_devices_setup(void)
{
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
return platform_add_devices(rsk_devices,
ARRAY_SIZE(rsk_devices));
}
......
......@@ -11,6 +11,8 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
#include <linux/i2c.h>
#include <linux/irq.h>
......@@ -38,6 +40,12 @@ static struct platform_device heartbeat_device = {
.resource = &heartbeat_resource,
};
/* Dummy supplies, where voltage doesn't matter */
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x"),
REGULATOR_SUPPLY("vdd33a", "smsc911x"),
};
static struct resource smsc911x_resources[] = {
[0] = {
.name = "smsc911x-memory",
......@@ -236,6 +244,8 @@ static void __init sdk7786_setup(char **cmdline_p)
{
pr_info("Renesas Technology Europe SDK7786 support:\n");
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
sdk7786_fpga_init();
sdk7786_nmi_init();
......
......@@ -18,6 +18,8 @@
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/mtd/physmap.h>
#include <linux/delay.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/smc91x.h>
#include <linux/gpio.h>
#include <linux/input.h>
......@@ -454,6 +456,15 @@ static struct platform_device sh7724_usb1_gadget_device = {
.resource = sh7724_usb1_gadget_resources,
};
/* Fixed 3.3V regulator to be used by SDHI0, SDHI1 */
static struct regulator_consumer_supply fixed3v3_power_consumers[] =
{
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
};
static struct resource sdhi0_cn7_resources[] = {
[0] = {
.name = "SDHI0",
......@@ -684,6 +695,10 @@ static int __init devices_setup(void)
&ms7724se_sdram_enter_end,
&ms7724se_sdram_leave_start,
&ms7724se_sdram_leave_end);
regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
/* Reset Release */
fpga_out = __raw_readw(FPGA_OUT);
/* bit4: NTSC_PDN, bit5: NTSC_RESET */
......
......@@ -283,5 +283,7 @@ enum {
SHDMA_SLAVE_RIIC8_RX,
SHDMA_SLAVE_RIIC9_TX,
SHDMA_SLAVE_RIIC9_RX,
SHDMA_SLAVE_RSPI_TX,
SHDMA_SLAVE_RSPI_RX,
};
#endif /* __ASM_SH7757_H__ */
......@@ -334,8 +334,8 @@ static struct clk_lookup lookups[] = {
CLKDEV_CON_ID("tpu0", &mstp_clks[HWBLK_TPU]),
CLKDEV_CON_ID("irda0", &mstp_clks[HWBLK_IRDA]),
CLKDEV_CON_ID("tsif0", &mstp_clks[HWBLK_TSIF]),
CLKDEV_CON_ID("usb1", &mstp_clks[HWBLK_USB1]),
CLKDEV_CON_ID("usb0", &mstp_clks[HWBLK_USB0]),
CLKDEV_DEV_ID("renesas_usbhs.1", &mstp_clks[HWBLK_USB1]),
CLKDEV_DEV_ID("renesas_usbhs.0", &mstp_clks[HWBLK_USB0]),
CLKDEV_CON_ID("2dg0", &mstp_clks[HWBLK_2DG]),
CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[HWBLK_SDHI0]),
CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[HWBLK_SDHI1]),
......
......@@ -12,6 +12,7 @@
#include <linux/platform_device.h>
#include <linux/serial.h>
#include <linux/serial_sci.h>
#include <linux/sh_dma.h>
#include <linux/sh_timer.h>
#include <linux/sh_intc.h>
#include <linux/uio_driver.h>
......