Commit aee3bfa3 authored by Linus Torvalds's avatar Linus Torvalds

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from Davic Miller:

 1) Support busy polling generically, for all NAPI drivers.  From Eric
    Dumazet.

 2) Add byte/packet counter support to nft_ct, from Floriani Westphal.

 3) Add RSS/XPS support to mvneta driver, from Gregory Clement.

 4) Implement IPV6_HDRINCL socket option for raw sockets, from Hannes
    Frederic Sowa.

 5) Add support for T6 adapter to cxgb4 driver, from Hariprasad Shenai.

 6) Add support for VLAN device bridging to mlxsw switch driver, from
    Ido Schimmel.

 7) Add driver for Netronome NFP4000/NFP6000, from Jakub Kicinski.

 8) Provide hwmon interface to mlxsw switch driver, from Jiri Pirko.

 9) Reorganize wireless drivers into per-vendor directories just like we
    do for ethernet drivers.  From Kalle Valo.

10) Provide a way for administrators "destroy" connected sockets via the
    SOCK_DESTROY socket netlink diag operation.  From Lorenzo Colitti.

11) Add support to add/remove multicast routes via netlink, from Nikolay
    Aleksandrov.

12) Make TCP keepalive settings per-namespace, from Nikolay Borisov.

13) Add forwarding and packet duplication facilities to nf_tables, from
    Pablo Neira Ayuso.

14) Dead route support in MPLS, from Roopa Prabhu.

15) TSO support for thunderx chips, from Sunil Goutham.

16) Add driver for IBM's System i/p VNIC protocol, from Thomas Falcon.

17) Rationalize, consolidate, and more completely document the checksum
    offloading facilities in the networking stack.  From Tom Herbert.

18) Support aborting an ongoing scan in mac80211/cfg80211, from
    Vidyullatha Kanchanapally.

19) Use per-bucket spinlock for bpf hash facility, from Tom Leiming.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1375 commits)
  net: bnxt: always return values from _bnxt_get_max_rings
  net: bpf: reject invalid shifts
  phonet: properly unshare skbs in phonet_rcv()
  dwc_eth_qos: Fix dma address for multi-fragment skbs
  phy: remove an unneeded condition
  mdio: remove an unneed condition
  mdio_bus: NULL dereference on allocation error
  net: Fix typo in netdev_intersect_features
  net: freescale: mac-fec: Fix build error from phy_device API change
  net: freescale: ucc_geth: Fix build error from phy_device API change
  bonding: Prevent IPv6 link local address on enslaved devices
  IB/mlx5: Add flow steering support
  net/mlx5_core: Export flow steering API
  net/mlx5_core: Make ipv4/ipv6 location more clear
  net/mlx5_core: Enable flow steering support for the IB driver
  net/mlx5_core: Initialize namespaces only when supported by device
  net/mlx5_core: Set priority attributes
  net/mlx5_core: Connect flow tables
  net/mlx5_core: Introduce modify flow table command
  net/mlx5_core: Managing root flow table
  ...
parents c597b6bc 415b6f19

Too many changes to show.

To preserve performance only 1000 of 1000+ files are displayed.

......@@ -19,6 +19,25 @@ Description:
Set to 0 to pad all frames. Set greater than tx_max to
disable all padding.
What: /sys/class/net/<iface>/cdc_ncm/ndp_to_end
Date: Dec 2015
KernelVersion: 4.5
Contact: Bjørn Mork <bjorn@mork.no>
Description:
Boolean attribute showing the status of the "NDP to
end" quirk. Defaults to 'N', except for devices
already known to need it enabled.
The "NDP to end" quirk makes the driver place the NDP
(the packet index table) after the payload. The NCM
specification does not mandate this, but some devices
are known to be more restrictive. Write 'Y' to this
attribute for temporary testing of a suspect device
failing to work with the default driver settings.
A device entry should be added to the driver if this
quirk is found to be required.
What: /sys/class/net/<iface>/cdc_ncm/rx_max
Date: May 2014
KernelVersion: 3.16
......
......@@ -8,7 +8,7 @@ Description:
What: /sys/class/net/<mesh_iface>/mesh/<vlan_subdir>/ap_isolation
Date: May 2011
Contact: Antonio Quartulli <antonio@meshcoding.com>
Contact: Antonio Quartulli <a@unstable.cc>
Description:
Indicates whether the data traffic going from a
wireless client to another wireless client will be
......@@ -70,7 +70,7 @@ Description:
What: /sys/class/net/<mesh_iface>/mesh/isolation_mark
Date: Nov 2013
Contact: Antonio Quartulli <antonio@meshcoding.com>
Contact: Antonio Quartulli <a@unstable.cc>
Description:
Defines the isolation mark (and its bitmask) which
is used to classify clients as "isolated" by the
......
What: /sys/class/net/<iface>/qmi/raw_ip
Date: Dec 2015
KernelVersion: 4.4
Contact: Bjørn Mork <bjorn@mork.no>
Description:
Boolean. Default: 'N'
Set this to 'Y' to change the network device link
framing from '802.3' to 'raw-ip'.
The netdev will change to reflect the link framing
mode. The netdev is an ordinary ethernet device in
'802.3' mode, and the driver expects to exchange
frames with an ethernet header over the USB link. The
netdev is a headerless p-t-p device in 'raw-ip' mode,
and the driver expects to echange IPv4 or IPv6 packets
without any L2 header over the USB link.
Userspace is in full control of firmware configuration
through the delegation of the QMI protocol. Userspace
is responsible for coordination of driver and firmware
link framing mode, changing this setting to 'Y' if the
firmware is configured for 'raw-ip' mode.
......@@ -31,6 +31,8 @@ A switch child node has the following optional property:
switch. Must be set if the switch can not detect
the presence and/or size of a connected EEPROM,
otherwise optional.
- reset-gpios : phandle and specifier to a gpio line connected to
reset pin of the switch chip.
A switch may have multiple "port" children nodes
......@@ -114,6 +116,7 @@ Example:
#size-cells = <0>;
reg = <17 1>; /* MDIO address 17, switch 1 in tree */
mii-bus = <&mii_bus1>;
reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
switch1port0: port@0 {
reg = <0>;
......
Hisilicon MDIO bus controller
Properties:
- compatible: "hisilicon,mdio","hisilicon,hns-mdio".
- compatible: can be one of:
"hisilicon,hns-mdio"
"hisilicon,mdio"
"hisilicon,hns-mdio" is recommended to be used for hip05 and later SOCs,
while "hisilicon,mdio" is optional for backwards compatibility only on
hip04 Soc.
- reg: The base address of the MDIO bus controller register bank.
- #address-cells: Must be <1>.
- #size-cells: Must be <0>. MDIO addresses have no size component.
......
* ADF7242 IEEE 802.15.4 *
Required properties:
- compatible: should be "adi,adf7242"
- spi-max-frequency: maximal bus speed (12.5 MHz)
- reg: the chipselect index
- interrupts: the interrupt generated by the device via pin IRQ1.
IRQ_TYPE_LEVEL_HIGH (4) or IRQ_TYPE_EDGE_FALLING (1)
Example:
adf7242@0 {
compatible = "adi,adf7242";
spi-max-frequency = <10000000>;
reg = <0>;
interrupts = <98 IRQ_TYPE_LEVEL_HIGH>;
interrupt-parent = <&gpio3>;
};
......@@ -4,6 +4,7 @@ Required properties:
- compatible: Should be "cdns,[<chip>-]{macb|gem}"
Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP
available on sama5d3 SoCs.
Use "cdns,np4-macb" for NP4 SoC devices.
Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb".
Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on
the Cadence GEM, or the generic form: "cdns,gem".
......@@ -19,6 +20,9 @@ Required properties:
Optional elements: 'tx_clk'
- clocks: Phandles to input clocks.
Optional properties for PHY child node:
- reset-gpios : Should specify the gpio for phy reset
Examples:
macb0: ethernet@fffc4000 {
......@@ -29,4 +33,8 @@ Examples:
local-mac-address = [3a 0e 03 04 05 06];
clock-names = "pclk", "hclk", "tx_clk";
clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
ethernet-phy@1 {
reg = <0x1>;
reset-gpios = <&pioE 6 1>;
};
};
Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
Some boards require special tuning values, particularly when it comes to
clock delays. You can specify clock delay values by adding
micrel-specific properties to an Ethernet OF device node.
Some boards require special tuning values, particularly when it comes
to clock delays. You can specify clock delay values in the PHY OF
device node. Deprecated, but still supported, these properties can
also be added to an Ethernet OF device node.
Note that these settings are applied after any phy-specific fixup from
phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
......@@ -57,16 +58,6 @@ KSZ9031:
Examples:
/* Attach to an Ethernet device with autodetected PHY */
&enet {
rxc-skew-ps = <3000>;
rxdv-skew-ps = <0>;
txc-skew-ps = <3000>;
txen-skew-ps = <0>;
status = "okay";
};
/* Attach to an explicitly-specified PHY */
mdio {
phy0: ethernet-phy@0 {
rxc-skew-ps = <3000>;
......
* STMicroelectronics : NFC Transceiver ST95HF
ST NFC Transceiver is required to attach with SPI bus.
ST95HF node should be defined in DT as SPI slave device of SPI
master with which ST95HF transceiver is physically connected.
The properties defined below are required to be the part of DT
to include ST95HF transceiver into the platform.
Required properties:
===================
- reg: Address of SPI slave "ST95HF transceiver" on SPI master bus.
- compatible: should be "st,st95hf" for ST95HF NFC transceiver
- spi-max-frequency: Max. operating SPI frequency for ST95HF
transceiver.
- enable-gpio: GPIO line to enable ST95HF transceiver.
- interrupt-parent : Standard way to specify the controller to which
ST95HF transceiver's interrupt is routed.
- interrupts : Standard way to define ST95HF transceiver's out
interrupt.
Optional property:
=================
- st95hfvin-supply : This is an optional property. It contains a
phandle to ST95HF transceiver's regulator supply node in DT.
Example:
=======
spi@9840000 {
reg = <0x9840000 0x110>;
#address-cells = <1>;
#size-cells = <0>;
cs-gpios = <&pio0 4>;
status = "okay";
st95hf@0{
reg = <0>;
compatible = "st,st95hf";
status = "okay";
spi-max-frequency = <1000000>;
enable-gpio = <&pio4 0>;
interrupt-parent = <&pio0>;
interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
};
};
......@@ -5,8 +5,18 @@ interface contains.
Required properties:
- compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
"renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC.
"renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC.
"renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC.