Commit 81093c98 authored by Cameron Gutman's avatar Cameron Gutman Committed by Dmitry Torokhov

Input: xpad - support some quirky Xbox One pads

There are several quirky Xbox One pads that depend on initialization
packets that the Microsoft pads don't require. To deal with these,
I've added a mechanism for issuing device-specific initialization
packets using a VID/PID-based quirks list.

For the initial set of init quirks, I have added quirk handling from
Valve's Steam Link xpad driver[0] and the 360Controller project[1] for
macOS to enable some new pads to work properly.

This should enable full functionality on the following quirky pads:
0x0e6f:0x0165 - Titanfall 2 gamepad (previously fully non-functional)
0x0f0d:0x0067 - Hori Horipad (analog sticks previously non-functional)
0x24c6:0x541a - PowerA Xbox One pad (previously fully non-functional)
0x24c6:0x542a - PowerA Xbox One pad (previously fully non-functional)
0x24c6:0x543a - PowerA Xbox One pad (previously fully non-functional)

[1]: default avatarCameron Gutman <>
Signed-off-by: default avatarDmitry Torokhov <>
parent c5cb37d0
......@@ -337,6 +337,64 @@ static struct usb_device_id xpad_table[] = {
MODULE_DEVICE_TABLE(usb, xpad_table);
struct xboxone_init_packet {
u16 idVendor;
u16 idProduct;
const u8 *data;
u8 len;
#define XBOXONE_INIT_PKT(_vid, _pid, _data) \
{ \
.idVendor = (_vid), \
.idProduct = (_pid), \
.data = (_data), \
.len = ARRAY_SIZE(_data), \
* This packet is required for all Xbox One pads with 2015
* or later firmware installed (or present from the factory).
static const u8 xboxone_fw2015_init[] = {
0x05, 0x20, 0x00, 0x01, 0x00
* This packet is required for the Titanfall 2 Xbox One pads
* (0x0e6f:0x0165) to finish initialization and for Hori pads
* (0x0f0d:0x0067) to make the analog sticks work.
static const u8 xboxone_hori_init[] = {
0x01, 0x20, 0x00, 0x09, 0x00, 0x04, 0x20, 0x3a,
0x00, 0x00, 0x00, 0x80, 0x00
* A rumble packet is required for some PowerA pads to start
* sending input reports. One of those pads is (0x24c6:0x543a).
static const u8 xboxone_zerorumble_init[] = {
0x09, 0x00, 0x00, 0x09, 0x00, 0x0F, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00
* This specifies the selection of init packets that a gamepad
* will be sent on init *and* the order in which they will be
* sent. The correct sequence number will be added when the
* packet is going to be sent.
static const struct xboxone_init_packet xboxone_init_packets[] = {
XBOXONE_INIT_PKT(0x0e6f, 0x0165, xboxone_hori_init),
XBOXONE_INIT_PKT(0x0f0d, 0x0067, xboxone_hori_init),
XBOXONE_INIT_PKT(0x0000, 0x0000, xboxone_fw2015_init),
XBOXONE_INIT_PKT(0x24c6, 0x541a, xboxone_zerorumble_init),
XBOXONE_INIT_PKT(0x24c6, 0x542a, xboxone_zerorumble_init),
XBOXONE_INIT_PKT(0x24c6, 0x543a, xboxone_zerorumble_init),
struct xpad_output_packet {
u8 data[XPAD_PKT_LEN];
u8 len;
......@@ -373,6 +431,7 @@ struct usb_xpad {
struct xpad_output_packet out_packets[XPAD_NUM_OUT_PACKETS];
int last_out_packet;
int init_seq;
struct xpad_led *led;
......@@ -747,12 +806,48 @@ exit:
__func__, retval);
/* Callers must hold xpad->odata_lock spinlock */
static bool xpad_prepare_next_init_packet(struct usb_xpad *xpad)
const struct xboxone_init_packet *init_packet;
if (xpad->xtype != XTYPE_XBOXONE)
return false;
/* Perform initialization sequence for Xbox One pads that require it */
while (xpad->init_seq < ARRAY_SIZE(xboxone_init_packets)) {
init_packet = &xboxone_init_packets[xpad->init_seq++];
if (init_packet->idVendor != 0 &&
init_packet->idVendor != xpad->dev->id.vendor)
if (init_packet->idProduct != 0 &&
init_packet->idProduct != xpad->dev->id.product)
/* This packet applies to our device, so prepare to send it */
memcpy(xpad->odata, init_packet->data, init_packet->len);
xpad->irq_out->transfer_buffer_length = init_packet->len;
/* Update packet with current sequence number */
xpad->odata[2] = xpad->odata_serial++;
return true;
return false;
/* Callers must hold xpad->odata_lock spinlock */
static bool xpad_prepare_next_out_packet(struct usb_xpad *xpad)
struct xpad_output_packet *pkt, *packet = NULL;
int i;
/* We may have init packets to send before we can send user commands */
if (xpad_prepare_next_init_packet(xpad))
return true;
for (i = 0; i < XPAD_NUM_OUT_PACKETS; i++) {
if (++xpad->last_out_packet >= XPAD_NUM_OUT_PACKETS)
xpad->last_out_packet = 0;
......@@ -938,24 +1033,17 @@ static int xpad_inquiry_pad_presence(struct usb_xpad *xpad)
static int xpad_start_xbox_one(struct usb_xpad *xpad)
struct xpad_output_packet *packet =
unsigned long flags;
int retval;
spin_lock_irqsave(&xpad->odata_lock, flags);
/* Xbox one controller needs to be initialized. */
packet->data[0] = 0x05;
packet->data[1] = 0x20;
packet->data[2] = xpad->odata_serial++; /* packet serial */
packet->data[3] = 0x01; /* rumble bit enable? */
packet->data[4] = 0x00;
packet->len = 5;
packet->pending = true;
/* Reset the sequence so we send out start packet first */
xpad->last_out_packet = -1;
* Begin the init sequence by attempting to send a packet.
* We will cycle through the init packet sequence before
* sending any packets from the output ring.
xpad->init_seq = 0;
retval = xpad_try_sending_next_out_packet(xpad);
spin_unlock_irqrestore(&xpad->odata_lock, flags);
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment