Tags give the ability to mark specific points in history as being important
  • xilinx-for-v2020.10-rc3   Xilinx changes for v2020.10-rc3 - Fix fdtfile variable setup - Fix bootm_*/fdt_high/initrd_high variables handling - Fix Kconfig dependencies for Xilinx drivers - Fix booting u-boot from lowest memory - Fix firmware payload argument count for Versal - Fix dfu configurations - Fix mio_bank property handling - Fix and align code around ID detection - Start to use ENV_VARS_UBOOT_RUNTIME_CONFIG - Simplify logic around reading MAC from eeprom - Decrease malloc length for zynqmp mini qspi - Enable preboot for ZynqMP and Versal i2c: - Fix i2c eeprom partitions handling mmc: - Fix logic around HS mode enabling and use proper functions
  • xilinx-for-v2020.10   Xilinx changes for v2020.10 Versal: - xspi bootmode fix - Removing one clock from clk driver - Align u-boot memory setting with OS by default - Map TCM and OCM by default ZynqMP: - Minor DT improvements - Reduce console buffer for mini configurations - Add fix for AMS - Add support for XDP platform Zynq: - Support for AES engine - Enable bigger memory test by default - Extend documentation for SD preparation - Use different freq for Topic miami board mmc: - minor GD pointer removal net: - Support fixed-link cases by zynq gem - Fix phy looking loop in axi enet driver spi: - Cleanup global macros for xilinx spi drivers firmware: - Add support for pmufw reloading fpga: - Improve error status reporting common: - Remove 4kB addition space for FDT allocation
  • xilinx-for-v2020.07-rc2   Xilinx changes for v2020.07-rc2 mmc: - Fix dt property handling via generic function clk: - Fix versal watchdog clock setting nand: - Fix zynq nand command comparison xilinx: - Enable ubifs - Sync board_late_init configurations with initrd_high setup - Make custom distro boot more verbose zynq: - Kconfig alignments - Fix nand cse configuration zynqmp: - Fix zcu104 low level qspi configuration - Small DT updates
  • xilinx-for-v2020.07   Xilinx changes for v2020.07 common: - Align ENV_FAT_INTERFACE - Fix MAC address source print log - Improve based autodetection code xilinx: - Enable netconsole Microblaze: - Setup default ENV_OFFSET/ENV_SECT_SIZE Zynq: - Multiple DT updates/fixes - Use DEVICE_TREE environment variable for DTB selection - Switch to single zynq configuration - Enable NOR flash via DM - Minor SPL print removal - Enable i2c mux driver ZynqMP: - Print multiboot register - Enable cache commands in mini mtest - Multiple DT updates/fixes - Fix firmware probing when driver is not enabled - Specify 3rd backup RAM boot mode in SPL - Add SPL support for zcu102 v1.1 and zcu111 revA - Redesign debug uart enabling and psu_init delay - Enable full u-boot run from EL3 - Enable u-boot.itb generation without ATF with U-Boot in EL3 Versal: - Enable distro default - Enable others SPI flashes - Enable systems without DDR Drivers: - Gem: - Flush memory after freeing - Handle mdio bus separately - Watchdog: - Get rid of unused global data pointer - Enable window watchdog timer - Serial: - Change reinitialization logic in zynq serial driver
  • xilinx-for-v2020.04-rc4   Xilinx fixes for v2020.04-rc4 - Fix link good bit handling in dp83867 - Rename generic Zynq defconfig - Fix zybo z7 low leve setup - Fix error path in zynq_gem driver and fix 64bit usage - Fix invalid clock name quieries for Versal - Fix zynq/zynqmp SPL low level configuration via DT selection
  • xilinx-for-v2020.04   Xilinx/FPGA changes for v2020.04 ARM64: - Add INIT_SPL_RELATIVE dependency SPL: - FIT image fix - Enable customization of bl2_plat_get_bl31_params() Pytest: - Add test for octal/hex conversions Microblaze: - Fix manual relocation for one SPI instance Nand: - Convert zynq/zynqmp drivers to DM Xilinx: - Enable boot script location via Kconfig - Support OF_SEPARATE in board FDT selection - Remove low level uart setup it is done later by code - Add support for DEVICE_TREE variable passing for SPL Zynq: - Enable jtag boot mode via distro boot - Removing unused baseaddresses from hardware.h - DT fixups ZynqMP: - Fix emmc boot sequence - Simplify spl logic around bss and board_init_r() - Support psu_post_config_data() calling - Tune mini-nand DTS - Fix psu wiring for a2197 boards - Add runtime MMC device boot order filling in spl - Clear ATF handoff handling with custom bl2_plat_get_bl31_params() - Add support u-boot.its generation - Use single image configuration for all platforms - Enable PANIC_HANG via Kconfig - DT fixups - Firmware fixes - Add support for zcu208 and zcu1285 Versal: - Fix emmc boot sequence - Enable board_late_init() by default
  • xilinx-for-v2020.01-part2   Xilinx/FPGA changes for v2020.01 part 2 common: - Fix manual relocation for repeatable commands arm: - Also clean up generated dtbos microblaze: - Add support for Manual relocation in crypto framework - Tune and align architecture bootm support zynq: - DT sync ups - Some defconfig updates - Remove empty board_early_init_f() zynqmp: - Clean firmware handing via drivers/firmware/ - DT/defconfig name alignments - DT cleanups with using firmware based clock driver - Some defconfig updates - Add IIO ina226 DT description - Tune zynqmp_psu_init_minimalize.sh script - Add single nand mini configuration, e-a2197, m-a2197-02/03 and zcu216 versal: - Clean firmware handing via drivers/firmware/ - Add gpio support - Enable DT overlay/USB/CLK/FPGA - DT updates - Tune mini configuration spi: - gqspi - Remove unused headers
  • xilinx-for-v2020.01   Xilinx/FPGA changes for v2020.01 FPGA: - Enable fpga loading on Versal - Minor fix Microblaze: - Fix LMB configurations to support initrds - Some other cleanups Zynq: - Minor config/dt changes - Add distro boot support for usb1 and mmc1 - Remove Xilinx private boot commands and use only distro boot ZynqMP: - Kconfig cleanups, defconfig updates - Update some dt files - Add firmware driver for talking to PMUFW - Extend distro boot support for jtag - Add new IDs - Add system controller configurations - Convert code to talk firmware via mailbox or SMCs Versal: - Add board_late_init() - Add run time DT memory setup - Add DFU support - Extend distro boot support for jtag and dfu - Add clock driver - Tune mini configurations Xilinx: - Improve documentation (boot scripts, dt binding) - Enable run time initrd_high calculation - Define default SYS_PROMPT - Add zynq/zynqmp virtual defconfig Drivers: - Add Xilinx mailbox driver for talking to firmware - Clean zynq_gem for Versal - Move ZYNQ_HISPD_BROKEN to Kconfig - Wire genphy_init() in phy.c - Add Xilinx gii2rgmii bridge - Cleanup zynq_sdhci - dwc3 fix - zynq_gpio fix - axi_emac fix Others: - apalis-tk1 - clean config file
  • xilinx-for-v2019.10   Xilinx/FPGA changes for v2019.10 fpga: - Xilinx virtex2 cleanup - Altera cyclon2 cleanup zynq: - Minor Kconfig cleanup - Add psu_init configuration for Z-turn board zynqmp: - Add support for pmufw config passing to PMU - script for psu_init conversion - zcu1275 renaming xilinx: - Add support for UltraZed-EV SoM
  • xilinx-for-v2019.07   Xilinx/FPGA changes for v2019.07 fpga: - Add support for external data in FIT - Extend testing for external data case - Inform user about a need to run post config on Zynq arm: - Tune zynq command functions - Fix internal variable setting arm64: - Add support for zc39dr decoding - Disable WDT for zcu100 - Small changes in reset_reason() - Some DT changes (spi) - Tune qspi-mini configuration - Remove useless eeprom setting - Fix two sdhci boot case spi: - Fix tap delay programming clk: - Enable i2c in SPL net: - Fix gem phydev handling - Remove phy detection code from gem driver general: - Correct EXT_DTB usage for MULTI_DTB_FIT configuration
  • xilinx-for-v2019.04-rc2   Xilinx changes for v2019.04-rc2 xilinx: - Start to use distro boot commands first - Setup fdtfile on ZynqMP - Move mac addr eeprom read to common location - Convert to OF_SEPARATE - Switch all board to DM_I2C - Some DT syncs i2c: - Remove !DM_I2C zynq driver versal: - Enable some more features - Add mini configurations
  • xilinx-for-v2019.04   Xilinx changes for v2019.04 tools: - Fix zynqmpimage generation zynq: - Some configs/Kconfig/DT updates - Enable REMAKE_ELF and OF_SEPARATE - Topic boards update - i2c cleanups and conversion to DM_I2C zynqmp: - Some configs/Kconfig/DT updates - Board config cleanup - Move arch folder to mach-zynqmp versal: - Enable DM_I2C, CMD_DM zynq-gem: - Fix driver cache handling i2c: - Live tree simple update phy: - Fixed phy cleanup travis: - Wire Versal SoC
  • xilinx-for-v2019.01   Xilinx changes for v2019.01 microblaze: - Use default functions for memory decoding - Showing model from DT zynq: - Fix spi flash DTs - Fix zynq_help_text with CONFIG_SYS_LONGHELP - Tune cse/mini configurations - Enabling cse/mini testing with current targets zynqmp: - Enable gzip SPL support - Fix chip detection logic - Tune mini configurations - DT fixes(spi-flash, models, clocks, etc) - Add support for OF_SEPARATE configurations - Enabling mini testing with current targets - Add mini mtest configuration - Some minor config setting nand: - arasan: Add subpage configuration net: - gem: Add 64bit DMA support
  • xilinx-for-v2018.11-rc3   Xilinx fixes for v2018.11-rc3 - Fix fit loading address for Zynq
  • xilinx-for-v2018.11-rc2-v2   Xilinx changes for v2018.11-rc2-v2 FPGA: - Fix SPL fpga loading from FIT ARM64: - Fix gic accesses in EL2/EL1 Xilinx: - Add dlc20 board support - Add Versal board support - Sync defconfigs - Enable MP via Kconfig - Add missing efuse node - Enable CDC for zcu100 cmd: - Fix kgdb Kconfig dependency
  • xilinx-for-v2018.11-rc2   Xilinx changes for v2018.11-rc2 FPGA: - Fix SPL fpga loading from FIT ARM64: - Fix gic accesses in EL2/EL1 Xilinx: - Add dlc20 board support - Add Versal board support - Sync defconfigs - Enable MP via Kconfig - Add missing efuse node - Enable CDC for zcu100 cmd: - Fix kgdb Kconfig dependency serial-pl01x: - Add support for handling clk from DT
  • xilinx-for-v2018.11   Xilinx changes for v2018.11 - Handle BOARD_LATE_INIT via Kconfig SPL: - Enable GZIP for all partitions types(not only for kernel) ZynqMP: - Rearrange pmufw version handling - Support newer PMUFW with improved fpga load sequence Zynq: - Cleanup config file - Simplify zybo config by enabling option via Kconfig net: - Fix gems max-speed property reading - Enable support for fixed-link phys
  • fpga-for-v2018.11   FPGA changes for v2018.11 - add fpga tests to cover fpga commands - fpga Kconfig cleanup - fix cmd/fpga.c - add support for missing fpga loadmk commands - add fpga fragment to MAINTAINERS
  • xilinx-for-v2018.09-rc2   Xilinx fixes for v2018.09-rc2 xilinx: - Add support for zybo z7 and ultra96 - Tune zynq and zynqmp mini configurations - Move SYS_MALLOC_LEN to Kconfig fdt - make static funcs gpio: - Fix soft gpio driver - Fix Zynq gpio driver by using platdata microblaze: - Fix Kconfig entry spi - Move ISSI to Kconfig
  • xilinx-for-v2018.09   Xilinx changes for v2018.09 clk: - Fix zynqmp clock driver common: - Handle CMD_RET_USAGE in cmd_process_error - Use return macros in cmd_process_error - Fix duplication of CONFIG_SYS_PROMPT_HUSH_PS2 - Support watchdog in usb_kbd.c - Fix name usage in usb_kbd.c - Support systems with non zero memory start initialized from DT only gpio: - Add support for manual relocation in uclass - zynq - use live tree - zynq - fix match data reading - zynq - setup bank name - xilinx - convert driver to DM microblaze: - Use generic iounmap/ioremap implementations - Redesign reset logic with sysreset features - Use watchdog and gpio over DM - Remove unused macros and fix some checkpatch issues - Fix timer initialization not to be called twice serial: - zynq - Use platdata intead of priv data sysreset: - Add support for manual relocation in uclass - Add gpio-restart driver - Add microblaze soft reset driver watchdog: - Add support for aliases in uclass - Add support for manual relocation in uclass - Convert xilinx driver to DM - cadence - update info in the driver and not stop wdt in probe xilinx: - Enable LED gpio for some targets with gpio-leds DT node - Setup variables via Kconfig zynq: - Add support for watchdog aliases - Add support for mini nand/nor configurations - Wire FPGA initalization in SPL zynqmp: - Enable mass storage for zcu100 - Handle external pmufw files - Add support for secure images - Some Kconfig movements and alignments - Add support for watchdog aliases - Use subcommands style for platform command - Add mmio_read/write platform commands - DT updates - Add support for mini qspi configuration