Xilinx changes for v2024.07-rc1

xilinx:
- Do not call env_get_location when !ENV_IS_NOWHERE
- Add FDT_FIXUP_PARTITIONS support
- Fix legacy format MAC decoding

zynqmp:
- Enable semihosting SPL support
- DT updates
- Kconfig resort/cleanup
- Don't describe second image/capsule if !SPL
- Add support for dfu/capsule description via MTD
- Support JTAG as alternative boot mode
- Add support for TEG soc variant

zynqmp-kria:
- Wire usb4 boot device
- Update SDIO tristate pin configuration
- Disable SPI_FLASH_BAR to avoid issue with SPI after update

mbv:
- Enable SPL and binman
- Small platform changes

zynqmp-nand:
- Error out in case of unsupported SW ECC
- Clean error path

versal-net:
- Support multiple locations for variables

Xilinx changes for v2024.04-rc3

zynqmp:
- Cover missing _SE chip variants to fix fpga programming

versal:
- Enable LTO for mini configurations

versal-net:
- Enable LTO for mini configurations
- Fix GIC address to aligned with real silicon

xilinx:
- DTs cleanup and fixups
- Enable HTTP boot
- Add missing spl header to zynqmp.c

Xilinx changes for v2024.04-rc1-v2

xilinx:
- Enable NFS, WGET, DNS and BLKMAP by default

zynqmp:
- Support new power-management node
- Remove multiple blank lines from DTSes
- Wire multiboot with DFU infrastructure
- Fix i2c-gpio pinctrl group name
- SOM DT changes (phy on kd240, kv260 cleanups
- Cleanup i2c bus on zcu1285
- DT cleanup (fix node names not to use _)
- Fix USB interrupts
- Cleanup zcu100 DT
- Add support for kaslr-seed

zynqmp_r5:
- Fix W=1 issue with missing dir

tools:
- Improve zynqmpimage mkimage support

Xilinx changes for v2024.04-rc1

zynqmp:
- Introduce Kria specific defconfig
- Calculate SPI image location based on boot offset
- DT updates

zynqmp-clk:
- Fix topsw_lsbus_clock for DP

axi-enet:
- Support older DT binding

mailbox:
- Add support for multiple mailboxes

pcie-xilinx:
- Covert driver to newer interface
- Enable MMIO region

zynq:
- dfu updates
- Enable capsule update for Antminer S9
- DT updates

xilinx_spi:
- Add new xfer callback and support runtime fifo depth discovery

Xilinx changes for v2024.01-rc3

xilinx:
- Disable lock in mini spi configurations

zynq:
- DTS syncups
- Kconfig updates

zynqmp:
- DTS syncups
- Kconfig fixups

versal:
- Make 30MHz as default freq for spi

versal net:
- Enable ADMA for mmc

serial:
- Read baudrate from DT

spi:
- Put spi lock under one Kconfig
- Support 64bit addresses in cadance_ospi
- zynqmp_gqspi - change logging support

firmware:
- Handle errors in zynqmp_pm_feature()

include:
- Sync vsc8531 dt binding with kernel

Xilinx changes for v2024.01-rc1 v3

clk:
- remove additional compatible strings for Versal NET

net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies

pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration

test:
- add test case for pxe get

Xilinx:
- describe SelectMAP boot mode

Zynq:
- Fix nand description in DT

ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
  description for other SC based boards
- k24 psu_init cleanup

Xilinx changes for v2024.01-rc1

clk:
- Dont return error when assigned-clocks is empty or missing

dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT

cmd:
- Fix flash_is_unlocked API

fpga:
- Define fpga_load() for debug build

global:
- U-Boot project name cleanup (next2)

net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT

pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True

spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior

trace:
- Fix flyrecord alignment issue

xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled

versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver

versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices

zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
  (high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address

Xilinx changes for v2024.01-rc1

ceva sata:
- Use generic_phy_valid() helper

clk:
- Dont return error when assigned-clocks is empty or missing

dm:
- Support reading a single indexed u64 value
- Add support for reading bootscript address/flash address from DT

cmd:
- Fix flash_is_unlocked API

fpga:
- Define fpga_load() for debug build

global:
- U-Boot project name cleanup (next2)

net:
- zynq_gem: Use generic_phy_valid() helper
- axienet: Convert to ofnode functions
- gmii2rgmii: Read bridge address from DT

pytest:
- skip tpm2_startup when env__tpm_device_test_skip=True

spi-nor:
- Add mx25u25635f support
- zynqmp_qspi: Tune cache behavior

trace:
- Fix flyrecord alignment issue

xilinx:
- Move scriptaddr to DT as bootscr-address
- Pick script_offset_f/script_size_f from DT as bootscr-flash-offset/size
- Do not generate distro boot variables if disabled

versal:
- Extend memory ranges to cover HBM
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices
- Clean mini targets bootcommand
- Fix clock driver

versal-net:
- Enable TPM, sha1sum and KASLRSEED
- Fix distroboot prioritization in connection to available devices

zynqmp;
- Allow AES to run from SPL
- Enable CMD_KASLRSEED
- Add proper dependencies for USB and remove ZYNQMP_USB
- Fix user si570 default frequency for zcu* boards
- Cover SOM rev2 revision
- Various DT changes
- Add firmware and pinctrl support for tristate configuration
  (high impedance/output enable)
- Add output-enable pins to SOMs
- Fix distroboot prioritization in connection to available devices
- Read bootscript address/flash address from DT
- Fix pcap_prog address

Xilinx changes for v2023.10-rc1 v2

axi_emac:
- Change return value if RX packet is not ready

cadence_qspi:
- Enable flash reset for Versal NET

dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location

fpga:
- Add load event

mtd:
- Add missing dependency for FLASH_CFI_MTD

spi/nand:
- Minor cleanup in Xilinx drivers

versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations

watchdog:
- Use new versal-wwdt property

xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email

zynqmp_clk:
- Add handling for gem rx/tsu clocks

zynq_gem:
- Configure mdio clock at run time

zynq:
- Enable fdt overlay support

zynq_sdhci:
- Call dll reset only for ZynqMP SOCs

Xilinx changes for v2023.10-rc1

global:
- Use proper U-Boot project name

Fix sparse warnings in zynqmp-clk, zynqmp handoff, board

cmd:
- Cover incorrect 0 length entries

Versal NET:
- Add bootmode logic
- Support SPP production version
- Add loadpdi command

ZynqMP:
- Clear pmufw node command ID handling
- Change power domain behavior around zynqmp_pmufw_node()
- Fix zynqmp cmd return values and pmufw command
- Fix R5 tcm init and modes

mmc:
- Sync Versal NET emmc DT binding

pcie:
- Add support for ZynqMP PCIe root port

video:
- Add support for ZynqMP DP

tools:
- Fix debug message in relocate-rela

Xilinx changes for v2023.07-rc3

.mailmap
- Fix Xilinx IDs

ZynqMP:
- Fix R5 split boot mode
- DT fixes - sync with Linux

Xilinx:
- Enable virtio and RNG support
- Enable ADI ethernet phy

SPI/Zynq:
- Fix dummy byte calculation

Xilinx changes for v2023.07-rc1

cmd:
- Print results in hex instead of dec in smc command

firmware:
- Cover missing ZYNQMP_FIRMWARE dependencies

fpga:
- fix loads for unencrypted use case

relocation
- Add support for BE systems

spi:
- Fix xilinx_spi init reset sequence

arasan nand:
- Remove hardcoded bbt option
- Set ofnode value

xilinx:
- Enable SMC command
- Fix some sparse issues

zynqmp:
- Remove cdns,zynq-gem compatible string
- Add optee node
- Some DT cleanups

zynq:
- Some DT cleanups

microblaze
- Remove MANUAL_RELOC option

Xilinx chnages for v2023.04-rc1

makefile:
- Add multi_dtb_fit dependency

clk:
- Handle error cases

microblaze:
- Disable falcon mode and cleanup code around

xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing

zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24

versal:
- Remove empty mini config files

versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations

zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy

spi:
- Add support for gigadevice parts

misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings

Xilinx changes for v2023.01-rc3-v2

xilinx:
- Fix MAC address selection for System Controller from FRU
- Cleanup Kconfig (ZYNQ_MAC_IN_EEPROM symbol)

versal:
- Create u-boot.elf for mini spi configurations

versal-net:
- Enable MT35XU flash

zynq:
- Add missing timer to DT for mini configurations

zynqmp:
- Do not include psu_init to U-Boot by default
- Do not enable IPI by default to mini U-Boot
- Update Luca's fragment
- Fix SPL_FS_LOAD_PAYLOAD_NAME usage

spi:
- gqspi: Fix tapdelay values
- gqspi: Fix 64bit address support
- cadence: Remove condition for calling enable linear mode
- nor-core: Invert logic to reflect sst26 flash unlocked

net:
- Add PCS/PMA phy support

Xilinx changes for v2023.01-rc3

microblaze:
- Enable 32 bit addressing mode for SPIs

zynq:
- Minor DT fixes (PL clock enabling)

zynqmp:
- Disable watchdog by default
- Remove unused xlnx,eeprom chosen support
- Add missing symlink for vck190 SC revB
- Use mdio bus with ethernet-phy-id description

versal:
- Add mini qspi/ospi configuration

versal-net:
- Add soc driver
- Fix Kconfig entry for SOC
- Fix loading address location for MINI configuration
- Disable LMB for mini configuration

net:
- Fix ethernet-phy-id usage in the code

pinctrl:
- Revert high impedance/output enable support

timer:
- Fix timer relocation for Microblaze
- Fix timer wrap in 32bit Xilinx timer driver

Xilinx changes for v2023.01-rc1 (round 3)

fpga:
- Create new uclass
- Get rid of FPGA_DEBUG and use logging infrastructure

zynq:
- Enable early EEPROM decoding
- Some DT updates

zynqmp:
- Use OCM_BANK_0 to check config loading permission
- Change config object loading in SPL
- Some DT updates

net:
- emaclite: Enable driver for RISC-V

xilinx:
- Fix static checker warnings
- Fix GCC12 warning

sdhci:
- Read PD id from DT

Xilinx changes for v2023.01-rc1 (round 2)

xilinx:
- Add support for new Versal NET SOC

zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio

versal:
- Config cleanup

Xilinx changes for v2023.01-rc1

cmd:
- bdinfo - guard LMB code to run only when LMB is enabled

timer:
- convert arm twd timer to DM

power-domain:
- Skip loading config object for Versal

xilinx:
- Fix logic when dfu_alt_info is generated
- Define only mmc devnum not partition
- Add xlnx prefix to GEM compatible string
- Add missing tca6416 to zynqmp SC - vck190
- Add env redund offset
- Enable CMD_GREPENV/SETEXPR by default
- Move board_get_usable_ram_top() to common location
- Add support for SOC detection

net/gem:
- Check rate before setting it up

microblaze:
- drop CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE
- Show cache size in bdinfo

spi:
- cadence_qspi: driver updates
- zynqmp_gqspi: driver updates
- zynqmp_gqspi: Add tap delays for Versal

zynq:
- Enable mkeficapsule compilation
- Use CONFIG_SPL_FS_LOAD_PAYLOAD_NAME for dfu_alt_info
- Align bss and end of u-boot image to 64bits
- Align qspi node name with Linux kernel
- DT: List OCM memory

zynqmp:
- Fix AES cache handling with a user provided key
- SOM: Add mtd partition for secure OS storage area
- Add ref_clk property for REFCLKPER calculation
- Fix mdio bus description for vck190-sc

xilinx-mini:
- Remove unneeded configs
- Disable LMB

versal:
- Enable i2c mux pca954x by default
- Define CONFIG_CQSPI_REF_CLK
- Enable power domain driver
- Enable zynqmp_gqspi driver

Xilinx changes for v2022.10-rc2

fpga:
- Convert SYS_FPGA_CHECK_CTRLC and SYS_FPGA_PROG_FEEDBACK to Kconfig
- Add support for secure bitstream loading

spi:
- xilinx_spi: Add support for memopers and supports_op
- zynq_qspi: Add support for supports_op/child_pre_probe
- zynq_qspi: Fix dummy cycle and qspi speed calculations

xilinx:
- Get rid of #stream-id-cells
- Use fixed partitions for SOM
- Add support for UUID reading from FRU
- Use strlcpy instead of strncpy
- Add reset driver support for ZynqMP and Versal
- Enable power domain driver in ZynqMP and Versal

zynqmp:
- Do no place BSS at 0 which have issue with NULL pointer
- Enable SLG gpio driver
- Disable LMB for mini configurations
- Remove duplicate PMIO_NODE_ID_BASE macro

versal:
- Add xlnx-versal-resets.h header

mmc:
- zynq_sdhci: Fix macro for MMC HS

relocate-rela:
- Fix support for BE hosts
- Define all macros for e_machine and reloc types

misc:
- Get rid of guard macros from ARM and RISC-V

lmb:
- Add support for disabling LMB

serial:
- zynq: Fix baudrate calculation

tests:
- Mark bind tests to run only on sandbox
- List also dm uclass and devres

Versal QSPI/OSPI changes for v2022.10

- Add new flash types
- Add cadence ospi driver for Xilinx Versal