README 108 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
wdenk's avatar
wdenk committed
2
# (C) Copyright 2000 - 2004
wdenk's avatar
wdenk committed
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#

Summary:
========

27 28 29 30
This directory contains the source code for U-Boot, a boot loader for
Embedded boards based on PowerPC and ARM processors, which can be
installed in a boot ROM and used to initialize and test the hardware
or to download and run application code.
wdenk's avatar
wdenk committed
31 32

The development of U-Boot is closely related to Linux: some parts of
33 34
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
35 36 37 38 39 40 41 42 43 44 45 46 47 48
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
49
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
50 51
"working". In fact, many of them are used in production systems.

52
In case of problems see the CHANGELOG and CREDITS files to find out
wdenk's avatar
wdenk committed
53 54 55 56 57 58
who contributed the specific port.


Where to get help:
==================

59 60 61 62
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
<u-boot-users@lists.sourceforge.net>. There is also an archive of
previous traffic on the mailing list - please search the archive
wdenk's avatar
wdenk committed
63 64 65 66 67 68 69 70
before asking FAQ's. Please see
http://lists.sourceforge.net/lists/listinfo/u-boot-users/


Where we come from:
===================

- start from 8xxrom sources
71
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
72 73 74 75 76 77 78 79
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
  * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
81
- add other CPU families (starting with ARM)
82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
- create U-Boot project (http://sourceforge.net/projects/u-boot)


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
105 106


wdenk's avatar
wdenk committed
107 108 109 110 111 112 113 114 115 116 117 118
Versioning:
===========

U-Boot uses a 3 level version number containing a version, a
sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
sub-version "34", and patchlevel "4".

The patchlevel is used to indicate certain stages of development
between released versions, i. e. officially released versions of
U-Boot will always have a patchlevel of "0".


wdenk's avatar
wdenk committed
119 120 121
Directory Hierarchy:
====================

wdenk's avatar
wdenk committed
122 123
- board		Board dependent files
- common	Misc architecture independent functions
wdenk's avatar
wdenk committed
124
- cpu		CPU specific files
wdenk's avatar
wdenk committed
125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145
  - 74xx_7xx	Files specific to Motorola MPC74xx and 7xx CPUs
  - arm720t	Files specific to ARM 720 CPUs
  - arm920t	Files specific to ARM 920 CPUs
  - arm925t	Files specific to ARM 925 CPUs
  - arm926ejs	Files specific to ARM 926 CPUs
  - at91rm9200	Files specific to Atmel AT91RM9200 CPUs
  - i386	Files specific to i386 CPUs
  - ixp		Files specific to Intel XScale IXP CPUs
  - mcf52x2	Files specific to Motorola ColdFire MCF52x2 CPUs
  - mips	Files specific to MIPS CPUs
  - mpc5xx	Files specific to Motorola MPC5xx  CPUs
  - mpc5xxx	Files specific to Motorola MPC5xxx CPUs
  - mpc8xx	Files specific to Motorola MPC8xx  CPUs
  - mpc824x	Files specific to Motorola MPC824x CPUs
  - mpc8260	Files specific to Motorola MPC8260 CPUs
  - mpc85xx	Files specific to Motorola MPC85xx CPUs
  - nios	Files specific to Altera NIOS CPUs
  - ppc4xx	Files specific to IBM PowerPC 4xx CPUs
  - pxa		Files specific to Intel XScale PXA CPUs
  - s3c44b0	Files specific to Samsung S3C44B0 CPUs
  - sa1100	Files specific to Intel StrongARM SA1100 CPUs
wdenk's avatar
wdenk committed
146 147
- disk		Code for disk drive partition handling
- doc		Documentation (don't expect too much)
wdenk's avatar
wdenk committed
148
- drivers	Commonly used device drivers
wdenk's avatar
wdenk committed
149 150 151
- dtt		Digital Thermometer and Thermostat drivers
- examples	Example code for standalone applications, etc.
- include	Header Files
wdenk's avatar
wdenk committed
152 153 154 155 156 157 158
- lib_arm	Files generic to ARM	 architecture
- lib_generic	Files generic to all	 architectures
- lib_i386	Files generic to i386	 architecture
- lib_m68k	Files generic to m68k	 architecture
- lib_mips	Files generic to MIPS	 architecture
- lib_nios	Files generic to NIOS	 architecture
- lib_ppc	Files generic to PowerPC architecture
wdenk's avatar
wdenk committed
159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214
- net		Networking code
- post		Power On Self Test
- rtc		Real Time Clock drivers
- tools		Tools to build S-Record or U-Boot images, etc.

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
  "CFG_".

Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".

Example: For a TQM823L module type:

	cd u-boot
	make TQM823L_config

For the Cogent platform, you need to specify the cpu type as well;
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.


Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
215 216 217 218 219
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.


wdenk's avatar
wdenk committed
220 221 222 223 224 225 226
The following options need to be configured:

- CPU Type:	Define exactly one of

		PowerPC based CPUs:
		-------------------
		CONFIG_MPC823,	CONFIG_MPC850,	CONFIG_MPC855,	CONFIG_MPC860
227
	or	CONFIG_MPC5xx
wdenk's avatar
wdenk committed
228
	or	CONFIG_MPC824X, CONFIG_MPC8260
229
	or	CONFIG_MPC85xx
wdenk's avatar
wdenk committed
230 231
	or	CONFIG_IOP480
	or	CONFIG_405GP
232
	or	CONFIG_405EP
wdenk's avatar
wdenk committed
233 234
	or	CONFIG_440
	or	CONFIG_MPC74xx
wdenk's avatar
wdenk committed
235
	or	CONFIG_750FX
wdenk's avatar
wdenk committed
236 237 238 239 240 241 242

		ARM based CPUs:
		---------------
		CONFIG_SA1110
		CONFIG_ARM7
		CONFIG_PXA250

wdenk's avatar
wdenk committed
243 244 245 246
		MicroBlaze based CPUs:
		----------------------
		CONFIG_MICROBLZE

wdenk's avatar
wdenk committed
247 248 249 250 251 252

- Board Type:	Define exactly one of

		PowerPC based boards:
		---------------------

253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283
		CONFIG_ADCIOP,		CONFIG_ADS860,		CONFIG_AMX860,
		CONFIG_AR405,		CONFIG_BAB7xx,		CONFIG_c2mon,
		CONFIG_CANBT,		CONFIG_CCM,		CONFIG_CMI,
		CONFIG_cogent_mpc8260,	CONFIG_cogent_mpc8xx,	CONFIG_CPCI405,
		CONFIG_CPCI4052,	CONFIG_CPCIISER4,	CONFIG_CPU86,
		CONFIG_CRAYL1,		CONFIG_CU824,		CONFIG_DASA_SIM,
		CONFIG_DB64360,		CONFIG_DB64460,		CONFIG_DU405,
		CONFIG_DUET_ADS,	CONFIG_EBONY,		CONFIG_ELPPC,
		CONFIG_ELPT860,		CONFIG_ep8260,		CONFIG_ERIC,
		CONFIG_ESTEEM192E,	CONFIG_ETX094,		CONFIG_EVB64260,
		CONFIG_FADS823,		CONFIG_FADS850SAR,	CONFIG_FADS860T,
		CONFIG_FLAGADM,		CONFIG_FPS850L,		CONFIG_FPS860L,
		CONFIG_GEN860T,		CONFIG_GENIETV,		CONFIG_GTH,
		CONFIG_gw8260,		CONFIG_hermes,		CONFIG_hymod,
		CONFIG_IAD210,		CONFIG_ICU862,		CONFIG_IP860,
		CONFIG_IPHASE4539,	CONFIG_IVML24,		CONFIG_IVML24_128,
		CONFIG_IVML24_256,	CONFIG_IVMS8,		CONFIG_IVMS8_128,
		CONFIG_IVMS8_256,	CONFIG_JSE,		CONFIG_LANTEC,
		CONFIG_lwmon,		CONFIG_MBX,		CONFIG_MBX860T,
		CONFIG_MHPC,		CONFIG_MIP405,		CONFIG_MOUSSE,
		CONFIG_MPC8260ADS,	CONFIG_MPC8540ADS,	CONFIG_MPC8560ADS,
		CONFIG_MUSENKI,		CONFIG_MVS1,		CONFIG_NETPHONE,
		CONFIG_NETTA,		CONFIG_NETVIA,		CONFIG_NX823,
		CONFIG_OCRTC,		CONFIG_ORSG,		CONFIG_OXC,
		CONFIG_PCI405,		CONFIG_PCIPPC2,		CONFIG_PCIPPC6,
		CONFIG_pcu_e,		CONFIG_PIP405,		CONFIG_PM826,
		CONFIG_ppmc8260,	CONFIG_QS823,		CONFIG_QS850,
		CONFIG_QS860T,		CONFIG_RBC823,		CONFIG_RPXClassic,
		CONFIG_RPXlite,		CONFIG_RPXsuper,	CONFIG_rsdproto,
		CONFIG_sacsng,		CONFIG_Sandpoint8240,	CONFIG_Sandpoint8245,
		CONFIG_sbc8260,		CONFIG_SM850,		CONFIG_SPD823TS,
wdenk's avatar
wdenk committed
284 285 286 287 288
		CONFIG_STXGP3,		CONFIG_SXNI855T,	CONFIG_TQM823L,
		CONFIG_TQM8260,		CONFIG_TQM850L,		CONFIG_TQM855L,
		CONFIG_TQM860L,		CONFIG_TTTech,		CONFIG_UTX8245,
		CONFIG_V37,		CONFIG_W7OLMC,		CONFIG_W7OLMG,
		CONFIG_WALNUT405,	CONFIG_ZPC1900,		CONFIG_ZUMA,
wdenk's avatar
wdenk committed
289 290 291 292

		ARM based boards:
		-----------------

293 294 295 296 297
		CONFIG_AT91RM9200DK,		CONFIG_DNP1110,		CONFIG_EP7312,
		CONFIG_H2_OMAP1610,		CONFIG_HHP_CRADLE,	CONFIG_IMPA7,
		CONFIG_INNOVATOROMAP1510,   CONFIG_INNOVATOROMAP1610,	CONFIG_LART,
		CONFIG_LUBBOCK,			CONFIG_SHANNON,		CONFIG_SMDK2400,
		CONFIG_SMDK2410,		CONFIG_TRAB,		CONFIG_VCMA9,
wdenk's avatar
wdenk committed
298

wdenk's avatar
wdenk committed
299 300 301 302 303
		MicroBlaze based boards:
		------------------------

		CONFIG_SUZAKU

wdenk's avatar
wdenk committed
304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325

- CPU Module Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
		CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
		CONFIG_CMA287_23, CONFIG_CMA287_50

- Motherboard Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA101, CONFIG_CMA102

- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
		Define one or more of
		CONFIG_CMA302

- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
		Define one or more of
		CONFIG_LCD_HEARTBEAT	- update a character position on
					  the lcd display every second with
					  a "rotator" |\-/|\-/

wdenk's avatar
wdenk committed
326 327 328 329
- Board flavour: (if CONFIG_MPC8260ADS is defined)
		CONFIG_ADSTYPE
		Possible values are:
			CFG_8260ADS	- original MPC8260ADS
330
			CFG_8266ADS	- MPC8266ADS
wdenk's avatar
wdenk committed
331
			CFG_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
332
			CFG_8272ADS	- MPC8272ADS
wdenk's avatar
wdenk committed
333

wdenk's avatar
wdenk committed
334
- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk's avatar
wdenk committed
335 336
		Define exactly one of
		CONFIG_MPC8240, CONFIG_MPC8245
wdenk's avatar
wdenk committed
337

338
- 8xx CPU Options: (if using an MPC8xx cpu)
wdenk's avatar
wdenk committed
339
		Define one or more of
wdenk's avatar
wdenk committed
340 341 342
		CONFIG_8xx_GCLK_FREQ	- if get_gclk_freq() cannot work
					  e.g. if there is no 32KHz
					  reference PIT/RTC clock
wdenk's avatar
wdenk committed
343

344 345 346 347 348 349 350 351 352
- 859/866 CPU options: (if using a MPC859 or MPC866 CPU):
		CFG_866_OSCCLK
		CFG_866_CPUCLK_MIN
		CFG_866_CPUCLK_MAX
		CFG_866_CPUCLK_DEFAULT
			See doc/README.MPC866

		CFG_MEASURE_CPUCLK

wdenk's avatar
wdenk committed
353 354 355 356 357 358
		Define this to measure the actual CPU clock instead
		of relying on the correctness of the configured
		values. Mostly useful for board bringup to make sure
		the PLL is locked at the intended frequency. Note
		that this requires a (stable) reference clock (32 kHz
		RTC clock),
359

wdenk's avatar
wdenk committed
360
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
361 362 363 364 365 366 367 368 369 370 371 372 373
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
		"clocks_in_mhz=1" is  automatically  included  in  the
		default environment.

wdenk's avatar
wdenk committed
374 375 376 377 378 379
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

		When transfering memsize parameter to linux, some versions
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

wdenk's avatar
wdenk committed
380
- Console Interface:
381 382 383 384
		Depending on board, define exactly one serial port
		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
		CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
		console by defining CONFIG_8xx_CONS_NONE
wdenk's avatar
wdenk committed
385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401

		Note: if CONFIG_8xx_CONS_NONE is defined, the serial
		port routines must be defined elsewhere
		(i.e. serial_init(), serial_getc(), ...)

		CONFIG_CFB_CONSOLE
		Enables console device for a color framebuffer. Needs following
		defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
			VIDEO_FB_LITTLE_ENDIAN	graphic memory organisation
						(default big endian)
			VIDEO_HW_RECTFILL	graphic chip supports
						rectangle fill
						(cf. smiLynxEM)
			VIDEO_HW_BITBLT		graphic chip supports
						bit-blit (cf. smiLynxEM)
			VIDEO_VISIBLE_COLS	visible pixel columns
						(cols=pitch)
wdenk's avatar
wdenk committed
402 403
			VIDEO_VISIBLE_ROWS	visible pixel rows
			VIDEO_PIXEL_SIZE	bytes per pixel
wdenk's avatar
wdenk committed
404 405
			VIDEO_DATA_FORMAT	graphic data format
						(0-5, cf. cfb_console.c)
wdenk's avatar
wdenk committed
406
			VIDEO_FB_ADRS		framebuffer address
wdenk's avatar
wdenk committed
407 408 409 410 411 412 413 414 415 416 417 418 419 420 421
			VIDEO_KBD_INIT_FCT	keyboard int fct
						(i.e. i8042_kbd_init())
			VIDEO_TSTC_FCT		test char fct
						(i.e. i8042_tstc)
			VIDEO_GETC_FCT		get char fct
						(i.e. i8042_getc)
			CONFIG_CONSOLE_CURSOR	cursor drawing on/off
						(requires blink timer
						cf. i8042.c)
			CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
			CONFIG_CONSOLE_TIME	display time/date info in
						upper right corner
						(requires CFG_CMD_DATE)
			CONFIG_VIDEO_LOGO	display Linux logo in
						upper left corner
422 423 424
			CONFIG_VIDEO_BMP_LOGO	use bmp_logo.h instead of
						linux_logo.h for logo.
						Requires CONFIG_VIDEO_LOGO
wdenk's avatar
wdenk committed
425 426 427 428
			CONFIG_CONSOLE_EXTRA_INFO
						addional board info beside
						the logo

429 430 431
		When CONFIG_CFB_CONSOLE is defined, video console is
		default i/o. Serial console can be forced with
		environment 'console=serial'.
wdenk's avatar
wdenk committed
432

wdenk's avatar
wdenk committed
433 434 435 436
		When CONFIG_SILENT_CONSOLE is defined, all console
		messages (by U-Boot and Linux!) can be silenced with
		the "silent" environment variable. See
		doc/README.silent for more information.
wdenk's avatar
wdenk committed
437

wdenk's avatar
wdenk committed
438 439 440 441
- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
		CFG_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
442
		CFG_BRGCLK_PRESCALE, baudrate prescale
wdenk's avatar
wdenk committed
443 444 445 446 447 448 449 450 451 452

- Interrupt driven serial port input:
		CONFIG_SERIAL_SOFTWARE_FIFO

		PPC405GP only.
		Use an interrupt handler for receiving data on the
		serial port. It also enables using hardware handshake
		(RTS/CTS) and UART's built-in FIFO. Set the number of
		bytes the interrupt driven input buffer should have.

453 454
		Leave undefined to disable this feature, including
		disable the buffer and hardware handshake.
wdenk's avatar
wdenk committed
455

stroese's avatar
stroese committed
456 457 458 459 460 461 462
- Console UART Number:
		CONFIG_UART1_CONSOLE

		IBM PPC4xx only.
		If defined internal UART1 (and not UART0) is used
		as default U-Boot console.

wdenk's avatar
wdenk committed
463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487
- Boot Delay:	CONFIG_BOOTDELAY - in seconds
		Delay before automatically booting the default image;
		set to -1 to disable autoboot.

		See doc/README.autoboot for these options that
		work with CONFIG_BOOTDELAY. None are required.
		CONFIG_BOOT_RETRY_TIME
		CONFIG_BOOT_RETRY_MIN
		CONFIG_AUTOBOOT_KEYED
		CONFIG_AUTOBOOT_PROMPT
		CONFIG_AUTOBOOT_DELAY_STR
		CONFIG_AUTOBOOT_STOP_STR
		CONFIG_AUTOBOOT_DELAY_STR2
		CONFIG_AUTOBOOT_STOP_STR2
		CONFIG_ZERO_BOOTDELAY_CHECK
		CONFIG_RESET_TO_RETRY

- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_BOOTARGS
488 489 490
		This can be used to pass arguments to the bootm
		command. The value of CONFIG_BOOTARGS goes into the
		environment value "bootargs".
wdenk's avatar
wdenk committed
491 492

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
493 494 495 496
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
		ram and nfs.
wdenk's avatar
wdenk committed
497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538

- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
		CFG_BAUDRATE_TABLE, see below.

- Monitor Functions:
		CONFIG_COMMANDS
		Most monitor functions can be selected (or
		de-selected) by adjusting the definition of
		CONFIG_COMMANDS; to select individual functions,
		#define CONFIG_COMMANDS by "OR"ing any of the
		following values:

		#define enables commands:
		-------------------------
		CFG_CMD_ASKENV	* ask for env variable
wdenk's avatar
wdenk committed
539
		CFG_CMD_AUTOSCRIPT Autoscript Support
wdenk's avatar
wdenk committed
540 541
		CFG_CMD_BDI	  bdinfo
		CFG_CMD_BEDBUG	  Include BedBug Debugger
wdenk's avatar
wdenk committed
542
		CFG_CMD_BMP	* BMP support
wdenk's avatar
wdenk committed
543 544 545 546 547
		CFG_CMD_BOOTD	  bootd
		CFG_CMD_CACHE	  icache, dcache
		CFG_CMD_CONSOLE	  coninfo
		CFG_CMD_DATE	* support for RTC, date/time...
		CFG_CMD_DHCP	  DHCP support
wdenk's avatar
wdenk committed
548 549 550
		CFG_CMD_DIAG	* Diagnostics
		CFG_CMD_DOC	* Disk-On-Chip Support
		CFG_CMD_DTT	  Digital Therm and Thermostat
wdenk's avatar
wdenk committed
551 552 553 554 555
		CFG_CMD_ECHO	* echo arguments
		CFG_CMD_EEPROM	* EEPROM read/write support
		CFG_CMD_ELF	  bootelf, bootvx
		CFG_CMD_ENV	  saveenv
		CFG_CMD_FDC	* Floppy Disk Support
556
		CFG_CMD_FAT	  FAT partition support
557
		CFG_CMD_FDOS	* Dos diskette Support
wdenk's avatar
wdenk committed
558 559
		CFG_CMD_FLASH	  flinfo, erase, protect
		CFG_CMD_FPGA	  FPGA device initialization support
wdenk's avatar
wdenk committed
560
		CFG_CMD_HWFLOW	* RTS/CTS hw flow control
wdenk's avatar
wdenk committed
561 562 563
		CFG_CMD_I2C	* I2C serial bus support
		CFG_CMD_IDE	* IDE harddisk support
		CFG_CMD_IMI	  iminfo
wdenk's avatar
wdenk committed
564
		CFG_CMD_IMLS	  List all found images
wdenk's avatar
wdenk committed
565 566
		CFG_CMD_IMMAP	* IMMR dump support
		CFG_CMD_IRQ	* irqinfo
wdenk's avatar
wdenk committed
567
		CFG_CMD_ITEST	* Integer/string test of 2 values
wdenk's avatar
wdenk committed
568
		CFG_CMD_JFFS2	* JFFS2 Support
wdenk's avatar
wdenk committed
569 570 571 572 573
		CFG_CMD_KGDB	* kgdb
		CFG_CMD_LOADB	  loadb
		CFG_CMD_LOADS	  loads
		CFG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
				  loop, mtest
wdenk's avatar
wdenk committed
574
		CFG_CMD_MISC	  Misc functions like sleep etc
575
		CFG_CMD_MMC	  MMC memory mapped support
wdenk's avatar
wdenk committed
576
		CFG_CMD_MII	  MII utility commands
wdenk's avatar
wdenk committed
577
		CFG_CMD_NAND	* NAND support
wdenk's avatar
wdenk committed
578 579 580
		CFG_CMD_NET	  bootp, tftpboot, rarpboot
		CFG_CMD_PCI	* pciinfo
		CFG_CMD_PCMCIA	* PCMCIA support
wdenk's avatar
wdenk committed
581 582
		CFG_CMD_PING	* send ICMP ECHO_REQUEST to network host
		CFG_CMD_PORTIO	* Port I/O
wdenk's avatar
wdenk committed
583 584
		CFG_CMD_REGINFO * Register dump
		CFG_CMD_RUN	  run command in env variable
wdenk's avatar
wdenk committed
585
		CFG_CMD_SAVES	  save S record dump
wdenk's avatar
wdenk committed
586
		CFG_CMD_SCSI	* SCSI Support
wdenk's avatar
wdenk committed
587
		CFG_CMD_SDRAM	* print SDRAM configuration information
wdenk's avatar
wdenk committed
588 589 590
		CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
		CFG_CMD_SPI	* SPI serial bus support
		CFG_CMD_USB	* USB support
wdenk's avatar
wdenk committed
591
		CFG_CMD_VFD	* VFD support (TRAB)
wdenk's avatar
wdenk committed
592
		CFG_CMD_BSP	* Board SPecific functions
593
		CFG_CMD_CDP	* Cisco Discover Protocol support
wdenk's avatar
wdenk committed
594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613
		-----------------------------------------------
		CFG_CMD_ALL	all

		CFG_CMD_DFL	Default configuration; at the moment
				this is includes all commands, except
				the ones marked with "*" in the list
				above.

		If you don't define CONFIG_COMMANDS it defaults to
		CFG_CMD_DFL in include/cmd_confdefs.h. A board can
		override the default settings in the respective
		include file.

		EXAMPLE: If you want all functions except of network
		support you can write:

		#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)


	Note:	Don't enable the "icache" and "dcache" commands
614 615 616 617 618 619 620
		(configuration option CFG_CMD_CACHE) unless you know
		what you (and your U-Boot users) are doing. Data
		cache cannot be enabled on systems like the 8xx or
		8260 (where accesses to the IMMR region must be
		uncached), and it cannot be disabled on all other
		systems where we (mis-) use the data cache to hold an
		initial stack and some data.
wdenk's avatar
wdenk committed
621 622 623 624 625 626 627


		XXX - this list needs to get updated!

- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
wdenk's avatar
wdenk committed
628
		support. There must be support in the platform specific
wdenk's avatar
wdenk committed
629 630 631 632
		code for a watchdog. For the 8xx and 8260 CPUs, the
		SIU Watchdog feature is enabled in the SYPCR
		register.

633 634 635 636 637 638 639
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
		This variable is readonly.

wdenk's avatar
wdenk committed
640 641 642 643 644 645 646 647 648
- Real-Time Clock:

		When CFG_CMD_DATE is selected, the type of the RTC
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_MPC8xx	- use internal RTC of MPC8xx
		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
		CONFIG_RTC_MC146818	- use MC146818 RTC
wdenk's avatar
wdenk committed
649
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
650
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
651
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
wdenk's avatar
wdenk committed
652
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
wdenk's avatar
wdenk committed
653

wdenk's avatar
wdenk committed
654 655 656
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

wdenk's avatar
wdenk committed
657 658
- Timestamp Support:

659 660 661 662
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
		automatically enabled when you select CFG_CMD_DATE .
wdenk's avatar
wdenk committed
663 664 665 666 667 668 669 670 671 672

- Partition Support:
		CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
		and/or CONFIG_ISO_PARTITION

		If IDE or SCSI support	is  enabled  (CFG_CMD_IDE  or
		CFG_CMD_SCSI) you must configure support for at least
		one partition type as well.

- IDE Reset method:
wdenk's avatar
wdenk committed
673 674
		CONFIG_IDE_RESET_ROUTINE - this is defined in several
		board configurations files but used nowhere!
wdenk's avatar
wdenk committed
675

wdenk's avatar
wdenk committed
676 677 678 679
		CONFIG_IDE_RESET - is this is defined, IDE Reset will
		be performed by calling the function
			ide_set_reset(int reset)
		which has to be defined in a board specific file
wdenk's avatar
wdenk committed
680 681 682 683 684 685

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

686 687 688 689 690 691 692 693 694 695 696 697
- LBA48 Support
		CONFIG_LBA48

		Set this to enable support for disks larger than 137GB
		Also look at CFG_64BIT_LBA ,CFG_64BIT_VSPRINTF and CFG_64BIT_STRTOUL
		Whithout these , LBA48 support uses 32bit variables and will 'only'
		support disks up to 2.1TB.

		CFG_64BIT_LBA:
			When enabled, makes the IDE subsystem use 64bit sector addresses.
			Default is 32bit.

wdenk's avatar
wdenk committed
698 699 700 701 702 703 704 705 706 707 708 709 710
- SCSI Support:
		At the moment only there is only support for the
		SYM53C8XX SCSI controller; define
		CONFIG_SCSI_SYM53C8XX to enable it.

		CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
		CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
		CFG_SCSI_MAX_LUN] can be adjusted to define the
		maximum numbers of LUNs, SCSI ID's and target
		devices.
		CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)

- NETWORK Support (PCI):
711 712
		CONFIG_E1000
		Support for Intel 8254x gigabit chips.
stroese's avatar
stroese committed
713

wdenk's avatar
wdenk committed
714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
		Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

wdenk's avatar
wdenk committed
730 731 732 733 734 735 736 737 738 739 740 741
- NETWORK Support (other):

		CONFIG_DRIVER_LAN91C96
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_BASE
			Define this to hold the physical address
			of the LAN91C96's I/O space

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

wdenk's avatar
wdenk committed
742 743
- USB Support:
		At the moment only the UHCI host controller is
wdenk's avatar
wdenk committed
744
		supported (PIP405, MIP405, MPC5200); define
wdenk's avatar
wdenk committed
745 746 747 748 749 750 751
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
		end define CONFIG_USB_STORAGE to enable the USB
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).
wdenk's avatar
wdenk committed
752 753 754 755 756 757 758
		MPC5200 USB requires additional defines:
			CONFIG_USB_CLOCK
				for 528 MHz Clock: 0x0001bbbb
			CONFIG_USB_CONFIG
				for differential drivers: 0x00001000
				for single ended drivers: 0x00005000

wdenk's avatar
wdenk committed
759

760
- MMC Support:
wdenk's avatar
wdenk committed
761 762 763
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
764 765
		to physical memory similar to flash. Command line is
		enabled with CFG_CMD_MMC. The MMC driver also works with
wdenk's avatar
wdenk committed
766
		the FAT fs. This is enabled with CFG_CMD_FAT.
767

wdenk's avatar
wdenk committed
768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790
- Keyboard Support:
		CONFIG_ISA_KEYBOARD

		Define this to enable standard (PC-Style) keyboard
		support

		CONFIG_I8042_KBD
		Standard PC keyboard driver with US (is default) and
		GERMAN key layout (switch via environment 'keymap=de') support.
		Export function i8042_kbd_init, i8042_tstc and i8042_getc
		for cfb_console. Supports cursor blinking.

- Video support:
		CONFIG_VIDEO

		Define this to enable video support (for output to
		video).

		CONFIG_VIDEO_CT69000

		Enable Chips & Technologies 69000 Video chip

		CONFIG_VIDEO_SMI_LYNXEM
wdenk's avatar
wdenk committed
791
		Enable Silicon Motion SMI 712/710/810 Video chip. The
wdenk's avatar
wdenk committed
792 793 794 795
		video output is selected via environment 'videoout'
		(1 = LCD and 2 = CRT). If videoout is undefined, CRT is
		assumed.

wdenk's avatar
wdenk committed
796 797
		For the CT69000 and SMI_LYNXEM drivers, videomode is
		selected via environment 'videomode'. Two diferent ways
wdenk's avatar
wdenk committed
798 799
		are possible:
		- "videomode=num"   'num' is a standard LiLo mode numbers.
wdenk's avatar
wdenk committed
800
		Following standard modes are supported	(* is default):
wdenk's avatar
wdenk committed
801 802 803 804 805 806 807 808

		      Colors	640x480 800x600 1024x768 1152x864 1280x1024
		-------------+---------------------------------------------
		      8 bits |	0x301*	0x303	 0x305	  0x161	    0x307
		     15 bits |	0x310	0x313	 0x316	  0x162	    0x319
		     16 bits |	0x311	0x314	 0x317	  0x163	    0x31A
		     24 bits |	0x312	0x315	 0x318	    ?	    0x31B
		-------------+---------------------------------------------
wdenk's avatar
wdenk committed
809 810
		(i.e. setenv videomode 317; saveenv; reset;)

wdenk's avatar
wdenk committed
811
		- "videomode=bootargs" all the video parameters are parsed
wdenk's avatar
wdenk committed
812 813 814
		from the bootargs. (See drivers/videomodes.c)


815
		CONFIG_VIDEO_SED13806
816
		Enable Epson SED13806 driver. This driver supports 8bpp
817 818 819
		and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
		or CONFIG_VIDEO_SED13806_16BPP

820
- Keyboard Support:
wdenk's avatar
wdenk committed
821
		CONFIG_KEYBOARD
822

wdenk's avatar
wdenk committed
823 824 825 826
		Define this to enable a custom keyboard support.
		This simply calls drv_keyboard_init() which must be
		defined in your board-specific files.
		The only board using this so far is RBC823.
827

wdenk's avatar
wdenk committed
828 829 830 831 832 833
- LCD Support:	CONFIG_LCD

		Define this to enable LCD support (for output to LCD
		display); also select one of the supported displays
		by defining one of these:

wdenk's avatar
wdenk committed
834
		CONFIG_NEC_NL6448AC33:
wdenk's avatar
wdenk committed
835

wdenk's avatar
wdenk committed
836
			NEC NL6448AC33-18. Active, color, single scan.
wdenk's avatar
wdenk committed
837

wdenk's avatar
wdenk committed
838
		CONFIG_NEC_NL6448BC20
wdenk's avatar
wdenk committed
839

wdenk's avatar
wdenk committed
840 841 842 843 844 845
			NEC NL6448BC20-08. 6.5", 640x480.
			Active, color, single scan.

		CONFIG_NEC_NL6448BC33_54

			NEC NL6448BC33-54. 10.4", 640x480.
wdenk's avatar
wdenk committed
846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875
			Active, color, single scan.

		CONFIG_SHARP_16x9

			Sharp 320x240. Active, color, single scan.
			It isn't 16x9, and I am not sure what it is.

		CONFIG_SHARP_LQ64D341

			Sharp LQ64D341 display, 640x480.
			Active, color, single scan.

		CONFIG_HLD1045

			HLD1045 display, 640x480.
			Active, color, single scan.

		CONFIG_OPTREX_BW

			Optrex	 CBL50840-2 NF-FW 99 22 M5
			or
			Hitachi	 LMG6912RPFC-00T
			or
			Hitachi	 SP14Q002

			320x240. Black & white.

		Normally display is black on white background; define
		CFG_WHITE_ON_BLACK to get it inverted.

wdenk's avatar
wdenk committed
876
- Splash Screen Support: CONFIG_SPLASH_SCREEN
877

wdenk's avatar
wdenk committed
878 879 880 881 882 883 884 885
		If this option is set, the environment is checked for
		a variable "splashimage". If found, the usual display
		of logo, copyright and system information on the LCD
		is supressed and the BMP image at the address
		specified in "splashimage" is loaded instead. The
		console is redirected to the "nulldev", too. This
		allows for a "silent" boot where a splash screen is
		loaded very quickly after power-on.
886

wdenk's avatar
wdenk committed
887 888 889 890 891 892 893
- Compression support:
		CONFIG_BZIP2

		If this option is set, support for bzip2 compressed
		images is included. If not, only uncompressed and gzip
		compressed images are supported.

894 895 896
		NOTE: the bzip2 algorithm requires a lot of RAM, so
		the malloc area (as defined by CFG_MALLOC_LEN) should
		be at least 4MB.
897

wdenk's avatar
wdenk committed
898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938
- Ethernet address:
		CONFIG_ETHADDR
		CONFIG_ETH2ADDR
		CONFIG_ETH3ADDR

		Define a default value for ethernet address to use
		for the respective ethernet interface, in case this
		is not determined automatically.

- IP address:
		CONFIG_IPADDR

		Define a default value for the IP address to use for
		the default ethernet interface, in case this is not
		determined through e.g. bootp.

- Server IP address:
		CONFIG_SERVERIP

		Defines a default value for theIP address of a TFTP
		server to contact when using the "tftboot" command.

- BOOTP Recovery Mode:
		CONFIG_BOOTP_RANDOM_DELAY

		If you have many targets in a network that try to
		boot using BOOTP, you may want to avoid that all
		systems send out BOOTP requests at precisely the same
		moment (which would happen for instance at recovery
		from a power failure, when all systems will try to
		boot, thus flooding the BOOTP server. Defining
		CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
		inserted before sending out BOOTP requests. The
		following delays are insterted then:

		1st BOOTP request:	delay 0 ... 1 sec
		2nd BOOTP request:	delay 0 ... 2 sec
		3rd BOOTP request:	delay 0 ... 4 sec
		4th and following
		BOOTP requests:		delay 0 ... 8 sec

939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961
- DHCP Advanced Options:
		CONFIG_BOOTP_MASK

		You can fine tune the DHCP functionality by adding
		these flags to the CONFIG_BOOTP_MASK define:

		CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
		serverip from a DHCP server, it is possible that more
		than one DNS serverip is offered to the client.
		If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
		serverip will be stored in the additional environment
		variable "dnsip2". The first DNS serverip is always
		stored in the variable "dnsip", when CONFIG_BOOTP_DNS
		is added to the CONFIG_BOOTP_MASK.

		CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
		to do a dynamic update of a DNS server. To do this, they
		need the hostname of the DHCP requester.
		If CONFIG_BOOP_SEND_HOSTNAME is added to the
		CONFIG_BOOTP_MASK, the content of the "hostname"
		environment variable is passed as option 12 to
		the DHCP server.

962
 - CDP Options:
wdenk's avatar
wdenk committed
963
		CONFIG_CDP_DEVICE_ID
964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003

		The device id used in CDP trigger frames.

		CONFIG_CDP_DEVICE_ID_PREFIX

		A two character string which is prefixed to the MAC address
		of the device.

		CONFIG_CDP_PORT_ID

		A printf format string which contains the ascii name of
		the port. Normally is set to "eth%d" which sets
		eth0 for the first ethernet, eth1 for the second etc.

		CONFIG_CDP_CAPABILITIES

		A 32bit integer which indicates the device capabilities;
		0x00000010 for a normal host which does not forwards.

		CONFIG_CDP_VERSION

		An ascii string containing the version of the software.

		CONFIG_CDP_PLATFORM

		An ascii string containing the name of the platform.

		CONFIG_CDP_TRIGGER

		A 32bit integer sent on the trigger.

		CONFIG_CDP_POWER_CONSUMPTION

		A 16bit integer containing the power consumption of the
		device in .1 of milliwatts.

		CONFIG_CDP_APPLIANCE_VLAN_TYPE

		A byte containing the id of the VLAN.

wdenk's avatar
wdenk committed
1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022
- Status LED:	CONFIG_STATUS_LED

		Several configurations allow to display the current
		status using a LED. For instance, the LED will blink
		fast while running U-Boot code, stop blinking as
		soon as a reply to a BOOTP request was received, and
		start blinking slow once the Linux kernel is running
		(supported by a status LED driver in the Linux
		kernel). Defining CONFIG_STATUS_LED enables this
		feature in U-Boot.

- CAN Support:	CONFIG_CAN_DRIVER

		Defining CONFIG_CAN_DRIVER enables CAN driver support
		on those systems that support this (optional)
		feature, like the TQM8xxL modules.

- I2C Support:	CONFIG_HARD_I2C | CONFIG_SOFT_I2C

wdenk's avatar
wdenk committed
1023
		These enable I2C serial bus commands. Defining either of
1024 1025
		(but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
		include the appropriate I2C driver for the selected cpu.
wdenk's avatar
wdenk committed
1026

1027 1028
		This will allow you to use i2c commands at the u-boot
		command line (as long as you set CFG_CMD_I2C in
wdenk's avatar
wdenk committed
1029 1030
		CONFIG_COMMANDS) and communicate with i2c based realtime
		clock chips. See common/cmd_i2c.c for a description of the
1031
		command line interface.
wdenk's avatar
wdenk committed
1032

wdenk's avatar
wdenk committed
1033
		CONFIG_HARD_I2C selects the CPM hardware driver for I2C.
wdenk's avatar
wdenk committed
1034

1035
		CONFIG_SOFT_I2C configures u-boot to use a software (aka
wdenk's avatar
wdenk committed
1036 1037
		bit-banging) driver instead of CPM or similar hardware
		support for I2C.
wdenk's avatar
wdenk committed
1038

1039
		There are several other quantities that must also be
wdenk's avatar
wdenk committed
1040
		defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
wdenk's avatar
wdenk committed
1041

wdenk's avatar
wdenk committed
1042
		In both cases you will need to define CFG_I2C_SPEED
1043 1044 1045 1046
		to be the frequency (in Hz) at which you wish your i2c bus
		to run and CFG_I2C_SLAVE to be the address of this node (ie
		the cpu's i2c node address).

wdenk's avatar
wdenk committed
1047 1048 1049
		Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
		sets the cpu up as a master node and so its address should
		therefore be cleared to 0 (See, eg, MPC823e User's Manual
1050
		p.16-473). So, set CFG_I2C_SLAVE to 0.
wdenk's avatar
wdenk committed
1051

1052
		That's all that's required for CONFIG_HARD_I2C.
wdenk's avatar
wdenk committed
1053

wdenk's avatar
wdenk committed
1054 1055 1056
		If you use the software i2c interface (CONFIG_SOFT_I2C)
		then the following macros need to be defined (examples are
		from include/configs/lwmon.h):
wdenk's avatar
wdenk committed
1057 1058 1059

		I2C_INIT

wdenk's avatar
wdenk committed
1060
		(Optional). Any commands necessary to enable the I2C
1061
		controller or configure ports.
wdenk's avatar
wdenk committed
1062

wdenk's avatar
wdenk committed
1063
		eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |=	PB_SCL)
wdenk's avatar
wdenk committed
1064

wdenk's avatar
wdenk committed
1065 1066
		I2C_PORT

1067 1068 1069
		(Only for MPC8260 CPU). The I/O port to use (the code
		assumes both bits are on the same port). Valid values
		are 0..3 for ports A..D.
wdenk's avatar
wdenk committed
1070 1071 1072 1073 1074 1075 1076

		I2C_ACTIVE

		The code necessary to make the I2C data line active
		(driven).  If the data line is open collector, this
		define can be null.

wdenk's avatar
wdenk committed
1077 1078
		eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |=  PB_SDA)

wdenk's avatar
wdenk committed
1079 1080 1081 1082 1083 1084
		I2C_TRISTATE

		The code necessary to make the I2C data line tri-stated
		(inactive).  If the data line is open collector, this
		define can be null.

wdenk's avatar
wdenk committed
1085 1086
		eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)

wdenk's avatar
wdenk committed
1087 1088 1089 1090 1091
		I2C_READ

		Code that returns TRUE if the I2C data line is high,
		FALSE if it is low.

wdenk's avatar
wdenk committed
1092 1093
		eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)

wdenk's avatar
wdenk committed
1094 1095 1096 1097 1098
		I2C_SDA(bit)

		If <bit> is TRUE, sets the I2C data line high. If it
		is FALSE, it clears it (low).

wdenk's avatar
wdenk committed
1099
		eg: #define I2C_SDA(bit) \
wdenk's avatar
wdenk committed
1100
			if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
wdenk's avatar
wdenk committed
1101
			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
wdenk's avatar
wdenk committed
1102

wdenk's avatar
wdenk committed
1103 1104 1105 1106 1107
		I2C_SCL(bit)

		If <bit> is TRUE, sets the I2C clock line high. If it
		is FALSE, it clears it (low).

wdenk's avatar
wdenk committed
1108
		eg: #define I2C_SCL(bit) \
wdenk's avatar
wdenk committed
1109
			if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
wdenk's avatar
wdenk committed
1110
			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
wdenk's avatar
wdenk committed
1111

wdenk's avatar
wdenk committed
1112 1113 1114 1115
		I2C_DELAY

		This delay is invoked four times per clock cycle so this
		controls the rate of data transfer.  The data rate thus
wdenk's avatar
wdenk committed
1116
		is 1 / (I2C_DELAY * 4). Often defined to be something
1117 1118
		like:

wdenk's avatar
wdenk committed
1119
		#define I2C_DELAY  udelay(2)
wdenk's avatar
wdenk committed
1120

1121 1122
		CFG_I2C_INIT_BOARD

wdenk's avatar
wdenk committed
1123 1124 1125 1126 1127 1128 1129 1130
		When a board is reset during an i2c bus transfer
		chips might think that the current transfer is still
		in progress. On some boards it is possible to access
		the i2c SCLK line directly, either by using the
		processor pin as a GPIO or by having a second pin
		connected to the bus. If this option is defined a
		custom i2c_init_board() routine in boards/xxx/board.c
		is run early in the boot sequence.
1131

wdenk's avatar
wdenk committed
1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144
- SPI Support:	CONFIG_SPI

		Enables SPI driver (so far only tested with
		SPI EEPROM, also an instance works with Crystal A/D and
		D/As on the SACSng board)

		CONFIG_SPI_X

		Enables extended (16-bit) SPI EEPROM addressing.
		(symmetrical to CONFIG_I2C_X)

		CONFIG_SOFT_SPI

1145 1146 1147 1148 1149 1150 1151
		Enables a software (bit-bang) SPI driver rather than
		using hardware support. This is a general purpose
		driver that only requires three general I/O port pins
		(two outputs, one input) to function. If this is
		defined, the board configuration must define several
		SPI configuration items (port pins to use, etc). For
		an example, see include/configs/sacsng.h.
wdenk's avatar
wdenk committed
1152

wdenk's avatar
wdenk committed
1153
- FPGA Support: CONFIG_FPGA_COUNT
wdenk's avatar
wdenk committed
1154

wdenk's avatar
wdenk committed
1155
		Specify the number of FPGA devices to support.
wdenk's avatar
wdenk committed
1156

wdenk's avatar
wdenk committed
1157
		CONFIG_FPGA
wdenk's avatar
wdenk committed
1158

wdenk's avatar
wdenk committed
1159 1160
		Used to specify the types of FPGA devices.  For example,
		#define CONFIG_FPGA  CFG_XILINX_VIRTEX2
wdenk's avatar
wdenk committed
1161

wdenk's avatar
wdenk committed
1162
		CFG_FPGA_PROG_FEEDBACK
wdenk's avatar
wdenk committed
1163

wdenk's avatar
wdenk committed
1164
		Enable printing of hash marks during FPGA configuration.
wdenk's avatar
wdenk committed
1165 1166 1167

		CFG_FPGA_CHECK_BUSY

1168 1169 1170 1171
		Enable checks on FPGA configuration interface busy
		status by the configuration function. This option
		will require a board or device specific function to
		be written.
wdenk's avatar
wdenk committed
1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182

		CONFIG_FPGA_DELAY

		If defined, a function that provides delays in the FPGA
		configuration driver.

		CFG_FPGA_CHECK_CTRLC
		Allow Control-C to interrupt FPGA configuration

		CFG_FPGA_CHECK_ERROR

1183 1184 1185 1186
		Check for configuration errors during FPGA bitfile
		loading. For example, abort during Virtex II
		configuration if the INIT_B line goes low (which
		indicated a CRC error).
wdenk's avatar
wdenk committed
1187 1188 1189

		CFG_FPGA_WAIT_INIT

1190 1191 1192 1193
		Maximum time to wait for the INIT_B line to deassert
		after PROB_B has been deasserted during a Virtex II
		FPGA configuration sequence. The default time is 500
		mS.
wdenk's avatar
wdenk committed
1194 1195 1196

		CFG_FPGA_WAIT_BUSY

1197 1198
		Maximum time to wait for BUSY to deassert during
		Virtex II FPGA configuration. The default is 5 mS.
wdenk's avatar
wdenk committed
1199 1200 1201

		CFG_FPGA_WAIT_CONFIG

1202 1203
		Time to wait after FPGA configuration. The default is
		200 mS.
wdenk's avatar
wdenk committed
1204 1205 1206 1207

- Configuration Management:
		CONFIG_IDENT_STRING

1208 1209
		If defined, this string will be added to the U-Boot
		version information (U_BOOT_VERSION)
wdenk's avatar
wdenk committed
1210 1211 1212

- Vendor Parameter Protection:

1213 1214
		U-Boot considers the values of the environment
		variables "serial#" (Board Serial Number) and
wdenk's avatar
wdenk committed
1215
		"ethaddr" (Ethernet Address) to be parameters that
1216 1217 1218 1219 1220
		are set once by the board vendor / manufacturer, and
		protects these variables from casual modification by
		the user. Once set, these variables are read-only,
		and write or delete attempts are rejected. You can
		change this behviour:
wdenk's avatar
wdenk committed
1221 1222 1223

		If CONFIG_ENV_OVERWRITE is #defined in your config
		file, the write protection for vendor parameters is
1224
		completely disabled. Anybody can change or delete
wdenk's avatar
wdenk committed
1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279
		these parameters.

		Alternatively, if you #define _both_ CONFIG_ETHADDR
		_and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
		ethernet address is installed in the environment,
		which can be changed exactly ONCE by the user. [The
		serial# is unaffected by this, i. e. it remains
		read-only.]

- Protected RAM:
		CONFIG_PRAM

		Define this variable to enable the reservation of
		"protected RAM", i. e. RAM which is not overwritten
		by U-Boot. Define CONFIG_PRAM to hold the number of
		kB you want to reserve for pRAM. You can overwrite
		this default value by defining an environment
		variable "pram" to the number of kB you want to
		reserve. Note that the board info structure will
		still show the full amount of RAM. If pRAM is
		reserved, a new environment variable "mem" will
		automatically be defined to hold the amount of
		remaining RAM in a form that can be passed as boot
		argument to Linux, for instance like that:

			setenv bootargs ... mem=\$(mem)
			saveenv

		This way you can tell Linux not to use this memory,
		either, which results in a memory region that will
		not be affected by reboots.

		*WARNING* If your board configuration uses automatic
		detection of the RAM size, you must make sure that
		this memory test is non-destructive. So far, the
		following board configurations are known to be
		"pRAM-clean":

			ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
			HERMES, IP860, RPXlite, LWMON, LANTEC,
			PCU_E, FLAGADM, TQM8260

- Error Recovery:
		CONFIG_PANIC_HANG

		Define this variable to stop the system in case of a
		fatal error, so that you have to reset it manually.
		This is probably NOT a good idea for an embedded
		system where you want to system to reboot
		automatically as fast as possible, but it may be
		useful during development since you can try to debug
		the conditions that lead to the situation.

		CONFIG_NET_RETRY_COUNT

1280 1281 1282 1283
		This variable defines the number of retries for
		network operations like ARP, RARP, TFTP, or BOOTP
		before giving up the operation. If not defined, a
		default value of 5 is used.
wdenk's avatar
wdenk committed
1284 1285

- Command Interpreter:
1286 1287 1288 1289
		CFG_AUTO_COMPLETE

		Enable auto completion of commands using TAB.

wdenk's avatar
wdenk committed
1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309
		CFG_HUSH_PARSER

		Define this variable to enable the "hush" shell (from
		Busybox) as command line interpreter, thus enabling
		powerful command line syntax like
		if...then...else...fi conditionals or `&&' and '||'
		constructs ("shell scripts").

		If undefined, you get the old, much simpler behaviour
		with a somewhat smaller memory footprint.


		CFG_PROMPT_HUSH_PS2

		This defines the secondary prompt string, which is
		printed when the command interpreter needs more input
		to complete a command. Usually "> ".

	Note:

wdenk's avatar
wdenk committed
1310 1311 1312 1313 1314 1315 1316
		In the current implementation, the local variables
		space and global environment variables space are
		separated. Local variables are those you define by
		simply typing `name=value'. To access a local
		variable later on, you have write `$name' or
		`${name}'; to execute the contents of a variable
		directly type `$name' at the command prompt.
wdenk's avatar
wdenk committed
1317

1318 1319 1320 1321
		Global environment variables are those you use
		setenv/printenv to work with. To run a command stored
		in such a variable, you need to use the run command,
		and you must not use the '$' sign to access them.
wdenk's avatar
wdenk committed
1322 1323 1324 1325 1326 1327 1328

		To store commands and special characters in a
		variable, please use double quotation marks
		surrounding the whole text of the variable, instead
		of the backslashes before semicolons and special
		symbols.

wdenk's avatar
wdenk committed
1329
- Default Environment:
wdenk's avatar
wdenk committed
1330 1331
		CONFIG_EXTRA_ENV_SETTINGS

1332 1333
		Define this to contain any number of null terminated
		strings (variable = value pairs) that will be part of
wdenk's avatar
wdenk committed
1334
		the default environment compiled into the boot image.
1335

1336 1337
		For example, place something like this in your
		board's config file:
wdenk's avatar
wdenk committed
1338 1339 1340 1341 1342

		#define CONFIG_EXTRA_ENV_SETTINGS \
			"myvar1=value1\0" \
			"myvar2=value2\0"

1343 1344 1345 1346
		Warning: This method is based on knowledge about the
		internal format how the environment is stored by the
		U-Boot code. This is NOT an official, exported
		interface! Although it is unlikely that this format
wdenk's avatar
wdenk committed
1347
		will change soon, there is no guarantee either.
wdenk's avatar
wdenk committed
1348 1349
		You better know what you are doing here.

1350 1351 1352 1353
		Note: overly (ab)use of the default environment is
		discouraged. Make sure to check other ways to preset
		the environment like the autoscript function or the
		boot command first.
wdenk's avatar
wdenk committed
1354

wdenk's avatar
wdenk committed
1355
- DataFlash Support:
1356 1357
		CONFIG_HAS_DATAFLASH

wdenk's avatar
wdenk committed
1358 1359 1360
		Defining this option enables DataFlash features and
		allows to read/write in Dataflash via the standard
		commands cp, md...
1361

wdenk's avatar
wdenk committed
1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375
- SystemACE Support:
		CONFIG_SYSTEMACE

		Adding this option adds support for Xilinx SystemACE
		chips attached via some sort of local bus. The address
		of the chip must alsh be defined in the
		CFG_SYSTEMACE_BASE macro. For example:

		#define CONFIG_SYSTEMACE
		#define CFG_SYSTEMACE_BASE 0xf0000000

		When SystemACE support is added, the "ace" device type
		becomes available to the fat commands, i.e. fatls.

wdenk's avatar
wdenk committed
1376
- Show boot progress:
wdenk's avatar
wdenk committed
1377 1378
		CONFIG_SHOW_BOOT_PROGRESS

1379 1380 1381 1382 1383 1384
		Defining this option allows to add some board-
		specific code (calling a user-provided function
		"show_boot_progress(int)") that enables you to show
		the system's boot progress on some display (for
		example, some LED's) on your board. At the moment,
		the following checkpoints are implemented:
wdenk's avatar
wdenk committed
1385 1386 1387

  Arg	Where			When
    1	common/cmd_bootm.c	before attempting to boot an image
wdenk's avatar
wdenk committed
1388
   -1	common/cmd_bootm.c	Image header has bad	 magic number
wdenk's avatar
wdenk committed
1389
    2	common/cmd_bootm.c	Image header has correct magic number
wdenk's avatar
wdenk committed
1390
   -2	common/cmd_bootm.c	Image header has bad	 checksum
wdenk's avatar
wdenk committed
1391
    3	common/cmd_bootm.c	Image header has correct checksum
wdenk's avatar
wdenk committed
1392
   -3	common/cmd_bootm.c	Image data   has bad	 checksum
wdenk's avatar
wdenk committed
1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404
    4	common/cmd_bootm.c	Image data   has correct checksum
   -4	common/cmd_bootm.c	Image is for unsupported architecture
    5	common/cmd_bootm.c	Architecture check OK
   -5	common/cmd_bootm.c	Wrong Image Type (not kernel, multi, standalone)
    6	common/cmd_bootm.c	Image Type check OK
   -6	common/cmd_bootm.c	gunzip uncompression error
   -7	common/cmd_bootm.c	Unimplemented compression type
    7	common/cmd_bootm.c	Uncompression OK
   -8	common/cmd_bootm.c	Wrong Image Type (not kernel, multi, standalone)
    8	common/cmd_bootm.c	Image Type check OK
   -9	common/cmd_bootm.c	Unsupported OS (not Linux, BSD, VxWorks, QNX)
    9	common/cmd_bootm.c	Start initial ramdisk verification
wdenk's avatar
wdenk committed
1405 1406
  -10	common/cmd_bootm.c	Ramdisk header has bad	   magic number
  -11	common/cmd_bootm.c	Ramdisk header has bad	   checksum
wdenk's avatar
wdenk committed
1407
   10	common/cmd_bootm.c	Ramdisk header is OK
wdenk's avatar
wdenk committed
1408
  -12	common/cmd_bootm.c	Ramdisk data   has bad	   checksum
wdenk's avatar
wdenk committed
1409 1410 1411 1412 1413 1414 1415
   11	common/cmd_bootm.c	Ramdisk data   has correct checksum
   12	common/cmd_bootm.c	Ramdisk verification complete, start loading
  -13	common/cmd_bootm.c	Wrong Image Type (not PPC Linux Ramdisk)
   13	common/cmd_bootm.c	Start multifile image verification
   14	common/cmd_bootm.c	No initial ramdisk, no multifile, continue.
   15	common/cmd_bootm.c	All preparation done, transferring control to OS

wdenk's avatar
wdenk committed
1416 1417 1418
  -30	lib_ppc/board.c		Fatal error, hang the system
  -31	post/post.c		POST test failed, detected by post_output_backlog()
  -32	post/post.c		POST test failed, detected by post_run_single()
1419

wdenk's avatar
wdenk committed
1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433
   -1	common/cmd_doc.c	Bad usage of "doc" command
   -1	common/cmd_doc.c	No boot device
   -1	common/cmd_doc.c	Unknown Chip ID on boot device
   -1	common/cmd_doc.c	Read Error on boot device
   -1	common/cmd_doc.c	Image header has bad magic number

   -1	common/cmd_ide.c	Bad usage of "ide" command
   -1	common/cmd_ide.c	No boot device
   -1	common/cmd_ide.c	Unknown boot device
   -1	common/cmd_ide.c	Unknown partition table
   -1	common/cmd_ide.c	Invalid partition type
   -1	common/cmd_ide.c	Read Error on boot device
   -1	common/cmd_ide.c	Image header has bad magic number

wdenk's avatar
wdenk committed
1434 1435 1436 1437 1438 1439
   -1	common/cmd_nand.c	Bad usage of "nand" command
   -1	common/cmd_nand.c	No boot device
   -1	common/cmd_nand.c	Unknown Chip ID on boot device
   -1	common/cmd_nand.c	Read Error on boot device
   -1	common/cmd_nand.c	Image header has bad magic number

wdenk's avatar
wdenk committed
1440
   -1	common/env_common.c	Environment has a bad CRC, using default
wdenk's avatar
wdenk committed
1441 1442 1443 1444 1445


Modem Support:
--------------

1446
[so far only for SMDK2400 and TRAB boards]
wdenk's avatar
wdenk committed
1447 1448 1449 1450 1451 1452 1453 1454 1455 1456

- Modem support endable:
		CONFIG_MODEM_SUPPORT

- RTS/CTS Flow control enable:
		CONFIG_HWFLOW

- Modem debug support:
		CONFIG_MODEM_SUPPORT_DEBUG

1457 1458
		Enables debugging stuff (char screen[1024], dbg())
		for modem support. Useful only with BDI2000.
wdenk's avatar
wdenk committed
1459

wdenk's avatar
wdenk committed
1460 1461
- Interrupt support (PPC):

wdenk's avatar
wdenk committed
1462 1463 1464 1465 1466 1467 1468 1469 1470 1471
		There are common interrupt_init() and timer_interrupt()
		for all PPC archs. interrupt_init() calls interrupt_init_cpu()
		for cpu specific initialization. interrupt_init_cpu()
		should set decrementer_count to appropriate value. If
		cpu resets decrementer automatically after interrupt
		(ppc4xx) it should set decrementer_count to zero.
		timer_interrupt() calls timer_interrupt_cpu() for cpu
		specific handling. If board has watchdog / status_led
		/ other_activity_monitor it works automatically from
		general timer_interrupt().
wdenk's avatar
wdenk committed
1472

wdenk's avatar
wdenk committed
1473 1474
- General:

1475 1476 1477 1478 1479 1480 1481
		In the target system modem support is enabled when a
		specific key (key combination) is pressed during
		power-on. Otherwise U-Boot will boot normally
		(autoboot). The key_pressed() fuction is called from
		board_init(). Currently key_pressed() is a dummy
		function, returning 1 and thus enabling modem
		initialization.
wdenk's avatar
wdenk committed
1482

1483 1484 1485 1486
		If there are no modem init strings in the
		environment, U-Boot proceed to autoboot; the
		previous output (banner, info printfs) will be
		supressed, though.
wdenk's avatar
wdenk committed
1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513

		See also: doc/README.Modem


Configuration Settings:
-----------------------

- CFG_LONGHELP: Defined when you want long help messages included;
		undefine this when you're short of memory.

- CFG_PROMPT:	This is what U-Boot prints on the console to
		prompt for user input.

- CFG_CBSIZE:	Buffer size for input from the Console

- CFG_PBSIZE:	Buffer size for Console output

- CFG_MAXARGS:	max. Number of arguments accepted for monitor commands

- CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
		the application (usually a Linux kernel) when it is
		booted

- CFG_BAUDRATE_TABLE:
		List of legal baudrate settings for this board.

- CFG_CONSOLE_INFO_QUIET
wdenk's avatar
wdenk committed
1514
		Suppress display of console information at boot.
wdenk's avatar
wdenk committed
1515 1516

- CFG_CONSOLE_IS_IN_ENV
wdenk's avatar
wdenk committed
1517 1518 1519
		If the board specific function
			extern int overwrite_console (void);
		returns 1, the stdin, stderr and stdout are switched to the
wdenk's avatar
wdenk committed
1520 1521 1522
		serial port, else the settings in the environment are used.

- CFG_CONSOLE_OVERWRITE_ROUTINE
wdenk's avatar
wdenk committed
1523
		Enable the call to overwrite_console().
wdenk's avatar
wdenk committed
1524 1525 1526 1527 1528 1529 1530 1531 1532

- CFG_CONSOLE_ENV_OVERWRITE
		Enable overwrite of previous console environment settings.

- CFG_MEMTEST_START, CFG_MEMTEST_END:
		Begin and End addresses of the area used by the
		simple memory test.

- CFG_ALT_MEMTEST:
wdenk's avatar
wdenk committed
1533
		Enable an alternate, more extensive memory test.
wdenk's avatar
wdenk committed
1534

1535 1536 1537 1538
- CFG_MEMTEST_SCRATCH:
		Scratch address used by the alternate memory test
		You only need to set this if address zero isn't writeable

wdenk's avatar
wdenk committed
1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561
- CFG_TFTP_LOADADDR:
		Default load address for network file downloads

- CFG_LOADS_BAUD_CHANGE:
		Enable temporary baudrate change while serial download

- CFG_SDRAM_BASE:
		Physical start address of SDRAM. _Must_ be 0 here.

- CFG_MBIO_BASE:
		Physical start address of Motherboard I/O (if using a
		Cogent motherboard)

- CFG_FLASH_BASE:
		Physical start address of Flash memory.

- CFG_MONITOR_BASE:
		Physical start address of boot monitor code (set by
		make config files to be same as the text base address
		(TEXT_BASE) used when linking) - same as
		CFG_FLASH_BASE when booting from flash.

- CFG_MONITOR_LEN:
wdenk's avatar
wdenk committed
1562 1563 1564 1565
		Size of memory reserved for monitor code, used to
		determine _at_compile_time_ (!) if the environment is
		embedded within the U-Boot image, or in a separate
		flash sector.
wdenk's avatar
wdenk committed
1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587

- CFG_MALLOC_LEN:
		Size of DRAM reserved for malloc() use.

- CFG_BOOTMAPSZ:
		Maximum size of memory mapped by the startup code of
		the Linux kernel; all data that must be processed by
		the Linux kernel (bd_info, boot arguments, eventually
		initrd image) must be put below this limit.

- CFG_MAX_FLASH_BANKS:
		Max number of Flash memory banks

- CFG_MAX_FLASH_SECT:
		Max number of sectors on a Flash chip

- CFG_FLASH_ERASE_TOUT:
		Timeout for Flash erase operations (in ms)

- CFG_FLASH_WRITE_TOUT:
		Timeout for Flash write operations (in ms)

1588 1589 1590 1591 1592 1593 1594 1595 1596 1597
- CFG_FLASH_LOCK_TOUT
		Timeout for Flash set sector lock bit operation (in ms)

- CFG_FLASH_UNLOCK_TOUT
		Timeout for Flash clear lock bits operation (in ms)

- CFG_FLASH_PROTECTION
		If defined, hardware flash sectors protection is used
		instead of U-Boot software protection.

wdenk's avatar
wdenk committed
1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611
- CFG_DIRECT_FLASH_TFTP:

		Enable TFTP transfers directly to flash memory;
		without this option such a download has to be
		performed in two steps: (1) download to RAM, and (2)
		copy from RAM to flash.

		The two-step approach is usually more reliable, since
		you can check if the download worked before you erase
		the flash, but in some situations (when sytem RAM is
		too limited to allow for a tempory copy of the
		downloaded image) this option may be very useful.

- CFG_FLASH_CFI:
1612
		Define if the flash driver uses extra elements in the
wdenk's avatar
wdenk committed
1613 1614 1615 1616 1617
		common flash structure for storing flash geometry.

- CFG_FLASH_CFI_DRIVER
		This option also enables the building of the cfi_flash driver
		in the drivers directory
wdenk's avatar
wdenk committed
1618

stroese's avatar
stroese committed
1619 1620 1621 1622 1623 1624 1625 1626
- CFG_RX_ETH_BUFFER:
		Defines the number of ethernet receive buffers. On some
		ethernet controllers it is recommended to set this value
		to 8 or even higher (EEPRO100 or 405 EMAC), since all
		buffers can be full shortly after enabling the interface
		on high ethernet traffic.
		Defaults to 4 if not defined.

wdenk's avatar
wdenk committed
1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:

- CFG_ENV_IS_IN_FLASH:

	Define this if the environment is in flash memory.

	a) The environment occupies one whole flash sector, which is
	   "embedded" in the text segment with the U-Boot code. This
	   happens usually with "bottom boot sector" or "top boot
	   sector" type flash chips, which have several smaller
	   sectors at the start or the end. For instance, such a
	   layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
	   such a case you would place the environment in one of the
	   4 kB sectors - with U-Boot code before and after it. With
	   "top boot sector" type flash chips, you would put the
	   environment in one of the last sectors, leaving a gap
	   between U-Boot and the environment.

	- CFG_ENV_OFFSET:

	   Offset of environment data (variable area) to the
	   beginning of flash memory; for instance, with bottom boot
	   type flash chips the second sector can be used: the offset
	   for this sector is given here.

	   CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.

	- CFG_ENV_ADDR:

	   This is just another way to specify the start address of
	   the flash sector containing the environment (instead of
	   CFG_ENV_OFFSET).

	- CFG_ENV_SECT_SIZE:

	   Size of the sector containing the environment.


	b) Sometimes flash chips have few, equal sized, BIG sectors.
	   In such a case you don't want to spend a whole sector for
	   the environment.

	- CFG_ENV_SIZE:

	   If you use this in combination with CFG_ENV_IS_IN_FLASH
	   and CFG_ENV_SECT_SIZE, you can specify to use only a part
	   of this flash sector for the environment. This saves
	   memory for the RAM copy of the environment.

	   It may also save flash memory if you decide to use this
	   when your environment is "embedded" within U-Boot code,
	   since then the remainder of the flash sector could be used
	   for U-Boot code. It should be pointed out that this is
	   STRONGLY DISCOURAGED from a robustness point of view:
	   updating the environment in flash makes it always
	   necessary to erase the WHOLE sector. If something goes
	   wrong before the contents has been restored from a copy in
	   RAM, your target system will be dead.

	- CFG_ENV_ADDR_REDUND
	  CFG_ENV_SIZE_REDUND

1691 1692
	   These settings describe a second storage area used to hold
	   a redundand copy of the environment data, so that there is
wdenk's avatar
wdenk committed
1693
	   a valid backup copy in case there is a power failure during
1694
	   a "saveenv" operation.
wdenk's avatar
wdenk committed
1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747

BE CAREFUL! Any changes to the flash layout, and some changes to the
source code will make it necessary to adapt <board>/u-boot.lds*
accordingly!


- CFG_ENV_IS_IN_NVRAM:

	Define this if you have some non-volatile memory device
	(NVRAM, battery buffered SRAM) which you want to use for the
	environment.

	- CFG_ENV_ADDR:
	- CFG_ENV_SIZE:

	  These two #defines are used to determin the memory area you
	  want to use for environment. It is assumed that this memory
	  can just be read and written to, without any special
	  provision.

BE CAREFUL! The first access to the environment happens quite early
in U-Boot initalization (when we try to get the setting of for the
console baudrate). You *MUST* have mappend your NVRAM area then, or
U-Boot will hang.

Please note that even with NVRAM we still use a copy of the
environment in RAM: we could work on NVRAM directly, but we want to
keep settings there always unmodified except somebody uses "saveenv"
to save the current settings.


- CFG_ENV_IS_IN_EEPROM:

	Use this if you have an EEPROM or similar serial access
	device and a driver for it.

	- CFG_ENV_OFFSET:
	- CFG_ENV_SIZE:

	  These two #defines specify the offset and size of the
	  environment area within the total memory of your EEPROM.

	- CFG_I2C_EEPROM_ADDR:
	  If defined, specified the chip address of the EEPROM device.
	  The default address is zero.

	- CFG_EEPROM_PAGE_WRITE_BITS:
	  If defined, the number of bits used to address bytes in a
	  single page in the EEPROM device.  A 64 byte page, for example
	  would require six bits.

	- CFG_EEPROM_PAGE_WRITE_DELAY_MS:
	  If defined, the number of milliseconds to delay between
wdenk's avatar
wdenk committed
1748
	  page writes.	The default is zero milliseconds.
wdenk's avatar
wdenk committed
1749 1750 1751 1752 1753

	- CFG_I2C_EEPROM_ADDR_LEN:
	  The length in bytes of the EEPROM memory array address.  Note
	  that this is NOT the chip address length!

1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764
	- CFG_I2C_EEPROM_ADDR_OVERFLOW:
	  EEPROM chips that implement "address overflow" are ones
	  like Catalyst 24WC04/08/16 which has 9/10/11 bits of
	  address and the extra bits end up in the "chip address" bit
	  slots. This makes a 24WC08 (1Kbyte) chip look like four 256
	  byte chips.

	  Note that we consider the length of the address field to
	  still be one byte because the extra address bits are hidden
	  in the chip address.

wdenk's avatar
wdenk committed
1765 1766 1767 1768
	- CFG_EEPROM_SIZE:
	  The size in bytes of the EEPROM device.


1769 1770
- CFG_ENV_IS_IN_DATAFLASH:

wdenk's avatar
wdenk committed
1771
	Define this if you have a DataFlash memory device which you
1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782
	want to use for the environment.

	- CFG_ENV_OFFSET:
	- CFG_ENV_ADDR:
	- CFG_ENV_SIZE:

	  These three #defines specify the offset and size of the
	  environment area within the total memory of your DataFlash placed
	  at the specified address.


wdenk's avatar
wdenk committed
1783 1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797
- CFG_SPI_INIT_OFFSET

	Defines offset to the initial SPI buffer area in DPRAM. The
	area is used at an early stage (ROM part) if the environment
	is configured to reside in the SPI EEPROM: We need a 520 byte
	scratch DPRAM area. It is used between the two initialization
	calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
	to be a good choice since it makes it far enough from the
	start of the data area as well as from the stack pointer.

Please note that the environment is read-only as long as the monitor
has been relocated to RAM and a RAM copy of the environment has been
created; also, when using EEPROM you will have to use getenv_r()
until then to read environment variables.

1798 1799 1800 1801 1802 1803
The environment is protected by a CRC32 checksum. Before the monitor
is relocated into RAM, as a result of a bad CRC you will be working
with the compiled-in default environment - *silently*!!! [This is
necessary, because the first environment variable we need is the
"baudrate" setting for the console - if we have a bad CRC, we don't
have any device yet where we could complain.]
wdenk's avatar
wdenk committed
1804 1805 1806

Note: once the monitor has been relocated, then it will complain if
the default environment is used; a new CRC is computed as soon as you
1807
use the "saveenv" command to store a valid environment.
wdenk's avatar
wdenk committed
1808

wdenk's avatar
wdenk committed
1809
- CFG_FAULT_ECHO_LINK_DOWN:
1810
		Echo the inverted Ethernet link state to the fault LED.
wdenk's avatar
wdenk committed
1811 1812 1813 1814 1815

		Note: If this option is active, then CFG_FAULT_MII_ADDR
		      also needs to be defined.

- CFG_FAULT_MII_ADDR:
1816
		MII address of the PHY to check for the Ethernet link state.
wdenk's avatar
wdenk committed
1817

1818 1819 1820 1821 1822 1823 1824
- CFG_64BIT_VSPRINTF:
		Makes vsprintf (and all *printf functions) support printing
		of 64bit values by using the L quantifier

- CFG_64BIT_STRTOUL:
		Adds simple_strtoull that returns a 64bit value

wdenk's avatar
wdenk committed
1825
Low Level (hardware related) configuration options:
wdenk's avatar
wdenk committed
1826
---------------------------------------------------
wdenk's avatar
wdenk committed
1827 1828 1829 1830 1831 1832

- CFG_CACHELINE_SIZE:
		Cache Line Size of the CPU.

- CFG_DEFAULT_IMMR:
		Default address of the IMMR after system reset.
wdenk's avatar
wdenk committed
1833

1834 1835 1836
		Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
		and RPXsuper) to be able to adjust the position of
		the IMMR register after a reset.
wdenk's avatar
wdenk committed
1837

wdenk's avatar
wdenk committed
1838 1839 1840 1841 1842 1843 1844 1845 1846 1847 1848 1849
- Floppy Disk Support:
		CFG_FDC_DRIVE_NUMBER

		the default drive number (default value 0)

		CFG_ISA_IO_STRIDE

		defines the spacing between fdc chipset registers
		(default value 1)

		CFG_ISA_IO_OFFSET

1850 1851 1852
		defines the offset of register from address. It
		depends on which part of the data bus is connected to
		the fdc chipset. (default value 0)
wdenk's avatar
wdenk committed
1853

1854 1855 1856
		If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
		CFG_FDC_DRIVE_NUMBER are undefined, they take their
		default value.
wdenk's avatar
wdenk committed
1857

1858 1859 1860 1861 1862
		if CFG_FDC_HW_INIT is defined, then the function
		fdc_hw_init() is called at the beginning of the FDC
		setup. fdc_hw_init() must be provided by the board
		source code. It is used to make hardware dependant
		initializations.
wdenk's avatar
wdenk committed
1863

wdenk's avatar
wdenk committed
1864 1865 1866 1867 1868 1869
- CFG_IMMR:	Physical address of the Internal Memory Mapped
		Register; DO NOT CHANGE! (11-4)
		[MPC8xx systems only]

- CFG_INIT_RAM_ADDR:

wdenk's avatar
wdenk committed
1870
		Start address of memory area that can be used for
wdenk's avatar
wdenk committed
1871 1872 1873 1874 1875 1876 1877 1878 1879 1880 1881 1882
		initial data and stack; please note that this must be
		writable memory that is working WITHOUT special
		initialization, i. e. you CANNOT use normal RAM which
		will become available only after programming the
		memory controller and running certain initialization
		sequences.

		U-Boot uses the following memory types:
		- MPC8xx and MPC8260: IMMR (internal memory of the CPU)
		- MPC824X: data cache
		- PPC4xx:  data cache

1883
- CFG_GBL_DATA_OFFSET:
wdenk's avatar
wdenk committed
1884 1885 1886

		Offset of the initial data structure in the memory
		area defined by CFG_INIT_RAM_ADDR. Usually
1887
		CFG_GBL_DATA_OFFSET is chosen such that the initial
wdenk's avatar
wdenk committed
1888 1889 1890 1891
		data is located at the end of the available space
		(sometimes written as (CFG_INIT_RAM_END -
		CFG_INIT_DATA_SIZE), and the initial stack is just
		below that area (growing from (CFG_INIT_RAM_ADDR +
1892
		CFG_GBL_DATA_OFFSET) downward.
wdenk's avatar
wdenk committed
1893 1894 1895 1896 1897 1898 1899 1900 1901 1902 1903 1904 1905 1906 1907 1908 1909 1910 1911 1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1943 1944 1945 1946 1947 1948 1949

	Note:
		On the MPC824X (or other systems that use the data
		cache for initial memory) the address chosen for
		CFG_INIT_RAM_ADDR is basically arbitrary - it must
		point to an otherwise UNUSED address space between
		the top of RAM and the start of the PCI space.

- CFG_SIUMCR:	SIU Module Configuration (11-6)

- CFG_SYPCR:	System Protection Control (11-9)

- CFG_TBSCR:	Time Base Status and Control (11-26)

- CFG_PISCR:	Periodic Interrupt Status and Control (11-31)

- CFG_PLPRCR:	PLL, Low-Power, and Reset Control Register (15-30)

- CFG_SCCR:	System Clock and reset Control Register (15-27)

- CFG_OR_TIMING_SDRAM:
		SDRAM timing

- CFG_MAMR_PTA:
		periodic timer for refresh

- CFG_DER:	Debug Event Register (37-47)

- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
  CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
  CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
  CFG_BR1_PRELIM:
		Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)