README 151 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
2
# (C) Copyright 2000 - 2009
wdenk's avatar
wdenk committed
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#

Summary:
========

27
This directory contains the source code for U-Boot, a boot loader for
wdenk's avatar
wdenk committed
28 29 30 31
Embedded boards based on PowerPC, ARM, MIPS and several other
processors, which can be installed in a boot ROM and used to
initialize and test the hardware or to download and run application
code.
wdenk's avatar
wdenk committed
32 33

The development of U-Boot is closely related to Linux: some parts of
34 35
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
36 37 38 39 40 41 42 43 44 45 46 47 48 49
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
50
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
51 52
"working". In fact, many of them are used in production systems.

53
In case of problems see the CHANGELOG and CREDITS files to find out
54 55
who contributed the specific port. The MAINTAINERS file lists board
maintainers.
wdenk's avatar
wdenk committed
56 57 58 59 60


Where to get help:
==================

61 62
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
63 64 65 66
<u-boot@lists.denx.de>. There is also an archive of previous traffic
on the mailing list - please search the archive before asking FAQ's.
Please see http://lists.denx.de/pipermail/u-boot and
http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
wdenk's avatar
wdenk committed
67 68


69 70 71 72 73 74 75 76
Where to get source code:
=========================

The U-Boot source code is maintained in the git repository at
git://www.denx.de/git/u-boot.git ; you can browse it online at
http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary

The "snapshot" links on this page allow you to download tarballs of
77
any version you might be interested in. Official releases are also
78 79 80
available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
directory.

81
Pre-built (and tested) images are available from
82 83 84
ftp://ftp.denx.de/pub/u-boot/images/


wdenk's avatar
wdenk committed
85 86 87 88
Where we come from:
===================

- start from 8xxrom sources
89
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
90 91 92 93 94 95 96
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
97
  * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
98
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
99
- add other CPU families (starting with ARM)
100
- create U-Boot project (http://sourceforge.net/projects/u-boot)
Magnus Lilja's avatar
Magnus Lilja committed
101
- current project page: see http://www.denx.de/wiki/U-Boot
102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
124 125


wdenk's avatar
wdenk committed
126 127 128
Versioning:
===========

129 130 131 132 133 134 135 136 137 138 139
Starting with the release in October 2008, the names of the releases
were changed from numerical release numbers without deeper meaning
into a time stamp based numbering. Regular releases are identified by
names consisting of the calendar year and month of the release date.
Additional fields (if present) indicate release candidates or bug fix
releases in "stable" maintenance trees.

Examples:
	U-Boot v2009.11     - Release November 2009
	U-Boot v2009.11.1   - Release 1 in version November 2009 stable tree
	U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
wdenk's avatar
wdenk committed
140 141


wdenk's avatar
wdenk committed
142 143 144
Directory Hierarchy:
====================

145 146 147 148 149
/arch			Architecture specific files
  /arm			Files generic to ARM architecture
    /cpu		CPU specific files
      /arm720t		Files specific to ARM 720 CPUs
      /arm920t		Files specific to ARM 920 CPUs
Wolfgang Denk's avatar
Wolfgang Denk committed
150 151 152
	/at91rm9200	Files specific to Atmel AT91RM9200 CPU
	/imx		Files specific to Freescale MC9328 i.MX CPUs
	/s3c24x0	Files specific to Samsung S3C24X0 CPUs
153 154 155 156 157 158 159 160 161 162 163 164 165 166
      /arm925t		Files specific to ARM 925 CPUs
      /arm926ejs	Files specific to ARM 926 CPUs
      /arm1136		Files specific to ARM 1136 CPUs
      /ixp		Files specific to Intel XScale IXP CPUs
      /pxa		Files specific to Intel XScale PXA CPUs
      /s3c44b0		Files specific to Samsung S3C44B0 CPUs
      /sa1100		Files specific to Intel StrongARM SA1100 CPUs
    /lib		Architecture specific library files
  /avr32		Files generic to AVR32 architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /blackfin		Files generic to Analog Devices Blackfin architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
Graeme Russ's avatar
Graeme Russ committed
167
  /x86			Files generic to x86 architecture
168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /m68k			Files generic to m68k architecture
    /cpu		CPU specific files
      /mcf52x2		Files specific to Freescale ColdFire MCF52x2 CPUs
      /mcf5227x		Files specific to Freescale ColdFire MCF5227x CPUs
      /mcf532x		Files specific to Freescale ColdFire MCF5329 CPUs
      /mcf5445x		Files specific to Freescale ColdFire MCF5445x CPUs
      /mcf547x_8x	Files specific to Freescale ColdFire MCF547x_8x CPUs
    /lib		Architecture specific library files
  /microblaze		Files generic to microblaze architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /mips			Files generic to MIPS architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /nios2		Files generic to Altera NIOS2 architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
Stefan Roese's avatar
Stefan Roese committed
187
  /powerpc		Files generic to PowerPC architecture
188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226
    /cpu		CPU specific files
      /74xx_7xx		Files specific to Freescale MPC74xx and 7xx CPUs
      /mpc5xx		Files specific to Freescale MPC5xx CPUs
      /mpc5xxx		Files specific to Freescale MPC5xxx CPUs
      /mpc8xx		Files specific to Freescale MPC8xx CPUs
      /mpc8220		Files specific to Freescale MPC8220 CPUs
      /mpc824x		Files specific to Freescale MPC824x CPUs
      /mpc8260		Files specific to Freescale MPC8260 CPUs
      /mpc85xx		Files specific to Freescale MPC85xx CPUs
      /ppc4xx		Files specific to AMCC PowerPC 4xx CPUs
    /lib		Architecture specific library files
  /sh			Files generic to SH architecture
    /cpu		CPU specific files
      /sh2		Files specific to sh2 CPUs
      /sh3		Files specific to sh3 CPUs
      /sh4		Files specific to sh4 CPUs
    /lib		Architecture specific library files
  /sparc		Files generic to SPARC architecture
    /cpu		CPU specific files
      /leon2		Files specific to Gaisler LEON2 SPARC CPU
      /leon3		Files specific to Gaisler LEON3 SPARC CPU
    /lib		Architecture specific library files
/api			Machine/arch independent API for external apps
/board			Board dependent files
/common			Misc architecture independent functions
/disk			Code for disk drive partition handling
/doc			Documentation (don't expect too much)
/drivers		Commonly used device drivers
/examples		Example code for standalone applications, etc.
/fs			Filesystem code (cramfs, ext2, jffs2, etc.)
/include		Header Files
/lib			Files generic to all architectures
  /libfdt		Library files to support flattened device trees
  /lzma			Library files to support LZMA decompression
  /lzo			Library files to support LZO decompression
/net			Networking code
/post			Power On Self Test
/rtc			Real Time Clock drivers
/tools			Tools to build S-Record or U-Boot images, etc.
wdenk's avatar
wdenk committed
227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
243
  "CONFIG_SYS_".
wdenk's avatar
wdenk committed
244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262

Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".

Example: For a TQM823L module type:

	cd u-boot
	make TQM823L_config

263
For the Cogent platform, you need to specify the CPU type as well;
wdenk's avatar
wdenk committed
264 265 266 267 268 269 270 271 272 273 274 275 276 277 278
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.


Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
279 280 281 282 283
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.


wdenk's avatar
wdenk committed
284 285
The following options need to be configured:

286 287 288
- CPU Type:	Define exactly one, e.g. CONFIG_MPC85XX.

- Board Type:	Define exactly one, e.g. CONFIG_MPC8540ADS.
289 290

- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
291
		Define exactly one, e.g. CONFIG_ATSTK1002
wdenk's avatar
wdenk committed
292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310

- CPU Module Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
		CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
		CONFIG_CMA287_23, CONFIG_CMA287_50

- Motherboard Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA101, CONFIG_CMA102

- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
		Define one or more of
		CONFIG_CMA302

- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
		Define one or more of
		CONFIG_LCD_HEARTBEAT	- update a character position on
311
					  the LCD display every second with
wdenk's avatar
wdenk committed
312 313
					  a "rotator" |\-/|\-/

wdenk's avatar
wdenk committed
314 315 316
- Board flavour: (if CONFIG_MPC8260ADS is defined)
		CONFIG_ADSTYPE
		Possible values are:
317 318 319 320
			CONFIG_SYS_8260ADS	- original MPC8260ADS
			CONFIG_SYS_8266ADS	- MPC8266ADS
			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
			CONFIG_SYS_8272ADS	- MPC8272ADS
wdenk's avatar
wdenk committed
321

322 323 324 325 326
- Marvell Family Member
		CONFIG_SYS_MVFS		- define it if you want to enable
					  multiple fs option at one time
					  for marvell soc family

wdenk's avatar
wdenk committed
327
- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk's avatar
wdenk committed
328 329
		Define exactly one of
		CONFIG_MPC8240, CONFIG_MPC8245
wdenk's avatar
wdenk committed
330

331
- 8xx CPU Options: (if using an MPC8xx CPU)
wdenk's avatar
wdenk committed
332 333
		CONFIG_8xx_GCLK_FREQ	- deprecated: CPU clock if
					  get_gclk_freq() cannot work
wdenk's avatar
wdenk committed
334 335
					  e.g. if there is no 32KHz
					  reference PIT/RTC clock
wdenk's avatar
wdenk committed
336 337
		CONFIG_8xx_OSCLK	- PLL input clock (either EXTCLK
					  or XTAL/EXTAL)
wdenk's avatar
wdenk committed
338

wdenk's avatar
wdenk committed
339
- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
340 341
		CONFIG_SYS_8xx_CPUCLK_MIN
		CONFIG_SYS_8xx_CPUCLK_MAX
wdenk's avatar
wdenk committed
342
		CONFIG_8xx_CPUCLK_DEFAULT
343 344
			See doc/README.MPC866

345
		CONFIG_SYS_MEASURE_CPUCLK
346

wdenk's avatar
wdenk committed
347 348 349 350 351
		Define this to measure the actual CPU clock instead
		of relying on the correctness of the configured
		values. Mostly useful for board bringup to make sure
		the PLL is locked at the intended frequency. Note
		that this requires a (stable) reference clock (32 kHz
352
		RTC clock or CONFIG_SYS_8XX_XIN)
353

354 355 356 357 358
		CONFIG_SYS_DELAYED_ICACHE

		Define this option if you want to enable the
		ICache only when Code runs from RAM.

359 360 361 362 363 364 365
- 85xx CPU Options:
		CONFIG_SYS_FSL_TBCLK_DIV

		Defines the core time base clock divider ratio compared to the
		system clock.  On most PQ3 devices this is 8, on newer QorIQ
		devices it can be 16 or 32.  The ratio varies from SoC to Soc.

366
- Intel Monahans options:
367
		CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
368 369 370 371 372

		Defines the Monahans run mode to oscillator
		ratio. Valid values are 8, 16, 24, 31. The core
		frequency is this value multiplied by 13 MHz.

373
		CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
Wolfgang Denk's avatar
Wolfgang Denk committed
374

375 376
		Defines the Monahans turbo mode to oscillator
		ratio. Valid values are 1 (default if undefined) and
Wolfgang Denk's avatar
Wolfgang Denk committed
377
		2. The core frequency as calculated above is multiplied
378
		by this value.
Wolfgang Denk's avatar
Wolfgang Denk committed
379

wdenk's avatar
wdenk committed
380
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
381 382 383 384 385 386 387 388 389 390
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
391
		"clocks_in_mhz=1" is automatically included in the
wdenk's avatar
wdenk committed
392 393
		default environment.

wdenk's avatar
wdenk committed
394 395
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

396
		When transferring memsize parameter to linux, some versions
wdenk's avatar
wdenk committed
397 398 399
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

400
		CONFIG_OF_LIBFDT
401 402

		New kernel versions are expecting firmware settings to be
403 404 405 406 407 408
		passed using flattened device trees (based on open firmware
		concepts).

		CONFIG_OF_LIBFDT
		 * New libfdt-based support
		 * Adds the "fdt" command
409
		 * The bootm command automatically updates the fdt
410

411 412 413 414
		OF_CPU - The proper name of the cpus node (only required for
			MPC512X and MPC5xxx based boards).
		OF_SOC - The proper name of the soc node (only required for
			MPC512X and MPC5xxx based boards).
415
		OF_TBCLK - The timebase frequency.
Kumar Gala's avatar
Kumar Gala committed
416
		OF_STDOUT_PATH - The path to the console device
417

418 419
		boards with QUICC Engines require OF_QE to set UCC MAC
		addresses
420

421 422 423 424
		CONFIG_OF_BOARD_SETUP

		Board code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel
425

426 427
		CONFIG_OF_BOOT_CPU

428
		This define fills in the correct boot CPU in the boot
429 430
		param header, the default value is zero if undefined.

431 432 433 434 435 436 437 438 439
		CONFIG_OF_IDE_FIXUP

		U-Boot can detect if an IDE device is present or not.
		If not, and this new config option is activated, U-Boot
		removes the ATA node from the DTS before booting Linux,
		so the Linux IDE driver does not probe the device and
		crash. This is needed for buggy hardware (uc101) where
		no pull down resistor is connected to the signal IDE5V_DD7.

440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457
- vxWorks boot parameters:

		bootvx constructs a valid bootline using the following
		environments variables: bootfile, ipaddr, serverip, hostname.
		It loads the vxWorks image pointed bootfile.

		CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
		CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
		CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
		CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters

		CONFIG_SYS_VXWORKS_ADD_PARAMS

		Add it at the end of the bootline. E.g "u=username pw=secret"

		Note: If a "bootargs" environment is defined, it will overwride
		the defaults discussed just above.

wdenk's avatar
wdenk committed
458
- Serial Ports:
459
		CONFIG_PL010_SERIAL
wdenk's avatar
wdenk committed
460 461 462

		Define this if you want support for Amba PrimeCell PL010 UARTs.

463
		CONFIG_PL011_SERIAL
wdenk's avatar
wdenk committed
464 465 466 467 468 469 470 471 472 473 474 475 476 477 478

		Define this if you want support for Amba PrimeCell PL011 UARTs.

		CONFIG_PL011_CLOCK

		If you have Amba PrimeCell PL011 UARTs, set this variable to
		the clock speed of the UARTs.

		CONFIG_PL01x_PORTS

		If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
		define this to a list of base addresses for each (supported)
		port. See e.g. include/configs/versatile.h


wdenk's avatar
wdenk committed
479
- Console Interface:
480 481 482 483
		Depending on board, define exactly one serial port
		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
		CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
		console by defining CONFIG_8xx_CONS_NONE
wdenk's avatar
wdenk committed
484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500

		Note: if CONFIG_8xx_CONS_NONE is defined, the serial
		port routines must be defined elsewhere
		(i.e. serial_init(), serial_getc(), ...)

		CONFIG_CFB_CONSOLE
		Enables console device for a color framebuffer. Needs following
		defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
			VIDEO_FB_LITTLE_ENDIAN	graphic memory organisation
						(default big endian)
			VIDEO_HW_RECTFILL	graphic chip supports
						rectangle fill
						(cf. smiLynxEM)
			VIDEO_HW_BITBLT		graphic chip supports
						bit-blit (cf. smiLynxEM)
			VIDEO_VISIBLE_COLS	visible pixel columns
						(cols=pitch)
wdenk's avatar
wdenk committed
501 502
			VIDEO_VISIBLE_ROWS	visible pixel rows
			VIDEO_PIXEL_SIZE	bytes per pixel
wdenk's avatar
wdenk committed
503 504
			VIDEO_DATA_FORMAT	graphic data format
						(0-5, cf. cfb_console.c)
wdenk's avatar
wdenk committed
505
			VIDEO_FB_ADRS		framebuffer address
wdenk's avatar
wdenk committed
506 507 508 509 510 511 512 513 514
			VIDEO_KBD_INIT_FCT	keyboard int fct
						(i.e. i8042_kbd_init())
			VIDEO_TSTC_FCT		test char fct
						(i.e. i8042_tstc)
			VIDEO_GETC_FCT		get char fct
						(i.e. i8042_getc)
			CONFIG_CONSOLE_CURSOR	cursor drawing on/off
						(requires blink timer
						cf. i8042.c)
515
			CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
wdenk's avatar
wdenk committed
516 517
			CONFIG_CONSOLE_TIME	display time/date info in
						upper right corner
518
						(requires CONFIG_CMD_DATE)
wdenk's avatar
wdenk committed
519 520
			CONFIG_VIDEO_LOGO	display Linux logo in
						upper left corner
521 522 523
			CONFIG_VIDEO_BMP_LOGO	use bmp_logo.h instead of
						linux_logo.h for logo.
						Requires CONFIG_VIDEO_LOGO
wdenk's avatar
wdenk committed
524
			CONFIG_CONSOLE_EXTRA_INFO
525
						additional board info beside
wdenk's avatar
wdenk committed
526 527
						the logo

528 529 530
		When CONFIG_CFB_CONSOLE is defined, video console is
		default i/o. Serial console can be forced with
		environment 'console=serial'.
wdenk's avatar
wdenk committed
531

wdenk's avatar
wdenk committed
532 533 534 535
		When CONFIG_SILENT_CONSOLE is defined, all console
		messages (by U-Boot and Linux!) can be silenced with
		the "silent" environment variable. See
		doc/README.silent for more information.
wdenk's avatar
wdenk committed
536

wdenk's avatar
wdenk committed
537 538 539
- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
540 541
		CONFIG_SYS_BAUDRATE_TABLE, see below.
		CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
wdenk's avatar
wdenk committed
542

543 544 545
- Console Rx buffer length
		With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
		the maximum receive buffer length for the SMC.
546
		This option is actual only for 82xx and 8xx possible.
547 548 549 550
		If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
		must be defined, to setup the maximum idle timeout for
		the SMC.

wdenk's avatar
wdenk committed
551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575
- Boot Delay:	CONFIG_BOOTDELAY - in seconds
		Delay before automatically booting the default image;
		set to -1 to disable autoboot.

		See doc/README.autoboot for these options that
		work with CONFIG_BOOTDELAY. None are required.
		CONFIG_BOOT_RETRY_TIME
		CONFIG_BOOT_RETRY_MIN
		CONFIG_AUTOBOOT_KEYED
		CONFIG_AUTOBOOT_PROMPT
		CONFIG_AUTOBOOT_DELAY_STR
		CONFIG_AUTOBOOT_STOP_STR
		CONFIG_AUTOBOOT_DELAY_STR2
		CONFIG_AUTOBOOT_STOP_STR2
		CONFIG_ZERO_BOOTDELAY_CHECK
		CONFIG_RESET_TO_RETRY

- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_BOOTARGS
576 577 578
		This can be used to pass arguments to the bootm
		command. The value of CONFIG_BOOTARGS goes into the
		environment value "bootargs".
wdenk's avatar
wdenk committed
579 580

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
581 582 583
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
584
		RAM and NFS.
wdenk's avatar
wdenk committed
585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610

- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

611
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
wdenk's avatar
wdenk committed
612 613
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
614
		CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
615 616

- Monitor Functions:
617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634
		Monitor commands can be included or excluded
		from the build by using the #include files
		"config_cmd_all.h" and #undef'ing unwanted
		commands, or using "config_cmd_default.h"
		and augmenting with additional #define's
		for wanted commands.

		The default command configuration includes all commands
		except those marked below with a "*".

		CONFIG_CMD_ASKENV	* ask for env variable
		CONFIG_CMD_BDI		  bdinfo
		CONFIG_CMD_BEDBUG	* Include BedBug Debugger
		CONFIG_CMD_BMP		* BMP support
		CONFIG_CMD_BSP		* Board specific commands
		CONFIG_CMD_BOOTD	  bootd
		CONFIG_CMD_CACHE	* icache, dcache
		CONFIG_CMD_CONSOLE	  coninfo
Mike Frysinger's avatar
Mike Frysinger committed
635
		CONFIG_CMD_CRC32	* crc32
636 637 638
		CONFIG_CMD_DATE		* support for RTC, date/time...
		CONFIG_CMD_DHCP		* DHCP support
		CONFIG_CMD_DIAG		* Diagnostics
639 640 641 642
		CONFIG_CMD_DS4510	* ds4510 I2C gpio commands
		CONFIG_CMD_DS4510_INFO	* ds4510 I2C info command
		CONFIG_CMD_DS4510_MEM	* ds4510 I2C eeprom/sram commansd
		CONFIG_CMD_DS4510_RST	* ds4510 I2C rst command
643 644
		CONFIG_CMD_DTT		* Digital Therm and Thermostat
		CONFIG_CMD_ECHO		  echo arguments
Peter Tyser's avatar
Peter Tyser committed
645
		CONFIG_CMD_EDITENV	  edit env variable
646 647
		CONFIG_CMD_EEPROM	* EEPROM read/write support
		CONFIG_CMD_ELF		* bootelf, bootvx
648
		CONFIG_CMD_EXPORTENV	* export the environment
649
		CONFIG_CMD_SAVEENV	  saveenv
650 651 652 653 654
		CONFIG_CMD_FDC		* Floppy Disk Support
		CONFIG_CMD_FAT		* FAT partition support
		CONFIG_CMD_FDOS		* Dos diskette Support
		CONFIG_CMD_FLASH	  flinfo, erase, protect
		CONFIG_CMD_FPGA		  FPGA device initialization support
Mike Frysinger's avatar
Mike Frysinger committed
655
		CONFIG_CMD_GO		* the 'go' command (exec code)
Kim Phillips's avatar
Kim Phillips committed
656
		CONFIG_CMD_GREPENV	* search environment
657 658 659 660 661 662
		CONFIG_CMD_HWFLOW	* RTS/CTS hw flow control
		CONFIG_CMD_I2C		* I2C serial bus support
		CONFIG_CMD_IDE		* IDE harddisk support
		CONFIG_CMD_IMI		  iminfo
		CONFIG_CMD_IMLS		  List all found images
		CONFIG_CMD_IMMAP	* IMMR dump support
663
		CONFIG_CMD_IMPORTENV	* import an environment
664 665 666 667
		CONFIG_CMD_IRQ		* irqinfo
		CONFIG_CMD_ITEST	  Integer/string test of 2 values
		CONFIG_CMD_JFFS2	* JFFS2 Support
		CONFIG_CMD_KGDB		* kgdb
668
		CONFIG_CMD_LDRINFO	  ldrinfo (display Blackfin loader)
669 670
		CONFIG_CMD_LOADB	  loadb
		CONFIG_CMD_LOADS	  loads
Robin Getz's avatar
Robin Getz committed
671 672
		CONFIG_CMD_MD5SUM	  print md5 message digest
					  (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
673 674 675 676 677
		CONFIG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
					  loop, loopw, mtest
		CONFIG_CMD_MISC		  Misc functions like sleep etc
		CONFIG_CMD_MMC		* MMC memory mapped support
		CONFIG_CMD_MII		* MII utility commands
678
		CONFIG_CMD_MTDPARTS	* MTD partition support
679 680
		CONFIG_CMD_NAND		* NAND support
		CONFIG_CMD_NET		  bootp, tftpboot, rarpboot
681 682
		CONFIG_CMD_PCA953X	* PCA953x I2C gpio commands
		CONFIG_CMD_PCA953X_INFO	* PCA953x I2C gpio info command
683 684 685 686 687 688 689 690 691 692 693 694 695
		CONFIG_CMD_PCI		* pciinfo
		CONFIG_CMD_PCMCIA		* PCMCIA support
		CONFIG_CMD_PING		* send ICMP ECHO_REQUEST to network
					  host
		CONFIG_CMD_PORTIO	* Port I/O
		CONFIG_CMD_REGINFO	* Register dump
		CONFIG_CMD_RUN		  run command in env variable
		CONFIG_CMD_SAVES	* save S record dump
		CONFIG_CMD_SCSI		* SCSI Support
		CONFIG_CMD_SDRAM	* print SDRAM configuration information
					  (requires CONFIG_CMD_I2C)
		CONFIG_CMD_SETGETDCR	  Support for DCR Register access
					  (4xx only)
696
		CONFIG_CMD_SHA1SUM	  print sha1 memory digest
Robin Getz's avatar
Robin Getz committed
697
					  (requires CONFIG_CMD_MEMORY)
698
		CONFIG_CMD_SOURCE	  "source" command Support
699 700 701 702 703 704
		CONFIG_CMD_SPI		* SPI serial bus support
		CONFIG_CMD_USB		* USB support
		CONFIG_CMD_VFD		* VFD support (TRAB)
		CONFIG_CMD_CDP		* Cisco Discover Protocol support
		CONFIG_CMD_FSL		* Microblaze FSL support

wdenk's avatar
wdenk committed
705 706 707 708

		EXAMPLE: If you want all functions except of network
		support you can write:

709 710
		#include "config_cmd_all.h"
		#undef CONFIG_CMD_NET
wdenk's avatar
wdenk committed
711

712 713
	Other Commands:
		fdt (flattened device tree) command: CONFIG_OF_LIBFDT
wdenk's avatar
wdenk committed
714 715

	Note:	Don't enable the "icache" and "dcache" commands
716
		(configuration option CONFIG_CMD_CACHE) unless you know
717 718 719 720 721 722
		what you (and your U-Boot users) are doing. Data
		cache cannot be enabled on systems like the 8xx or
		8260 (where accesses to the IMMR region must be
		uncached), and it cannot be disabled on all other
		systems where we (mis-) use the data cache to hold an
		initial stack and some data.
wdenk's avatar
wdenk committed
723 724 725 726 727 728 729


		XXX - this list needs to get updated!

- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
wdenk's avatar
wdenk committed
730
		support. There must be support in the platform specific
wdenk's avatar
wdenk committed
731 732 733 734
		code for a watchdog. For the 8xx and 8260 CPUs, the
		SIU Watchdog feature is enabled in the SYPCR
		register.

735 736 737 738 739 740 741
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
		This variable is readonly.

wdenk's avatar
wdenk committed
742 743
- Real-Time Clock:

744
		When CONFIG_CMD_DATE is selected, the type of the RTC
wdenk's avatar
wdenk committed
745 746 747 748 749
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_MPC8xx	- use internal RTC of MPC8xx
		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
Guennadi Liakhovetski's avatar
Guennadi Liakhovetski committed
750
		CONFIG_RTC_MC13783	- use MC13783 RTC
wdenk's avatar
wdenk committed
751
		CONFIG_RTC_MC146818	- use MC146818 RTC
wdenk's avatar
wdenk committed
752
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
753
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
754
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
wdenk's avatar
wdenk committed
755
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
756
		CONFIG_RTC_ISL1208	- use Intersil ISL1208 RTC
wdenk's avatar
wdenk committed
757
		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
758
		CONFIG_SYS_RTC_DS1337_NOOSC	- Turn off the OSC output for DS1337
759 760
		CONFIG_SYS_RV3029_TCR	- enable trickle charger on
					  RV3029 RTC.
wdenk's avatar
wdenk committed
761

wdenk's avatar
wdenk committed
762 763 764
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

765 766 767 768
- GPIO Support:
		CONFIG_PCA953X		- use NXP's PCA953X series I2C GPIO
		CONFIG_PCA953X_INFO	- enable pca953x info command

769 770 771 772
		The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
		chip-ngpio pairs that tell the PCA953X driver the number of
		pins supported by a particular chip.

773 774 775
		Note that if the GPIO device uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

wdenk's avatar
wdenk committed
776 777
- Timestamp Support:

778 779 780
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
781
		automatically enabled when you select CONFIG_CMD_DATE .
wdenk's avatar
wdenk committed
782 783 784

- Partition Support:
		CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
785
		and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
wdenk's avatar
wdenk committed
786

787 788 789
		If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
		CONFIG_CMD_SCSI) you must configure support for at
		least one partition type as well.
wdenk's avatar
wdenk committed
790 791

- IDE Reset method:
wdenk's avatar
wdenk committed
792 793
		CONFIG_IDE_RESET_ROUTINE - this is defined in several
		board configurations files but used nowhere!
wdenk's avatar
wdenk committed
794

wdenk's avatar
wdenk committed
795 796 797 798
		CONFIG_IDE_RESET - is this is defined, IDE Reset will
		be performed by calling the function
			ide_set_reset(int reset)
		which has to be defined in a board specific file
wdenk's avatar
wdenk committed
799 800 801 802 803 804

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

805 806 807 808
- LBA48 Support
		CONFIG_LBA48

		Set this to enable support for disks larger than 137GB
809
		Also look at CONFIG_SYS_64BIT_LBA.
810 811 812
		Whithout these , LBA48 support uses 32bit variables and will 'only'
		support disks up to 2.1TB.

813
		CONFIG_SYS_64BIT_LBA:
814 815 816
			When enabled, makes the IDE subsystem use 64bit sector addresses.
			Default is 32bit.

wdenk's avatar
wdenk committed
817 818 819 820 821
- SCSI Support:
		At the moment only there is only support for the
		SYM53C8XX SCSI controller; define
		CONFIG_SCSI_SYM53C8XX to enable it.

822 823 824
		CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
		CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
		CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
wdenk's avatar
wdenk committed
825 826
		maximum numbers of LUNs, SCSI ID's and target
		devices.
827
		CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
wdenk's avatar
wdenk committed
828 829

- NETWORK Support (PCI):
830 831
		CONFIG_E1000
		Support for Intel 8254x gigabit chips.
stroese's avatar
stroese committed
832

Andre Schwarz's avatar
Andre Schwarz committed
833
		CONFIG_E1000_FALLBACK_MAC
834
		default MAC for empty EEPROM after production.
Andre Schwarz's avatar
Andre Schwarz committed
835

wdenk's avatar
wdenk committed
836 837
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
838
		Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
wdenk's avatar
wdenk committed
839 840 841 842 843 844 845 846 847 848 849 850 851
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

wdenk's avatar
wdenk committed
852 853
- NETWORK Support (other):

854 855 856 857 858 859 860 861 862 863
		CONFIG_DRIVER_AT91EMAC
		Support for AT91RM9200 EMAC.

			CONFIG_RMII
			Define this to use reduced MII inteface

			CONFIG_DRIVER_AT91EMAC_QUIET
			If this defined, the driver is quiet.
			The driver doen't show link status messages.

wdenk's avatar
wdenk committed
864 865 866 867 868 869 870 871 872 873
		CONFIG_DRIVER_LAN91C96
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_BASE
			Define this to hold the physical address
			of the LAN91C96's I/O space

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

wdenk's avatar
wdenk committed
874 875 876 877 878 879 880 881 882 883 884 885 886 887
		CONFIG_DRIVER_SMC91111
		Support for SMSC's LAN91C111 chip

			CONFIG_SMC91111_BASE
			Define this to hold the physical address
			of the device (I/O space)

			CONFIG_SMC_USE_32_BIT
			Define this if data bus is 32 bits

			CONFIG_SMC_USE_IOFUNCS
			Define this to use i/o functions instead of macros
			(some hardware wont work with macros)

888 889 890 891 892 893 894 895 896 897 898 899
		CONFIG_FTGMAC100
		Support for Faraday's FTGMAC100 Gigabit SoC Ethernet

			CONFIG_FTGMAC100_EGIGA
			Define this to use GE link update with gigabit PHY.
			Define this if FTGMAC100 is connected to gigabit PHY.
			If your system has 10/100 PHY only, it might not occur
			wrong behavior. Because PHY usually return timeout or
			useless data when polling gigabit status and gigabit
			control registers. This behavior won't affect the
			correctnessof 10/100 link speed update.

900
		CONFIG_SMC911X
Jens Gehrlein's avatar
Jens Gehrlein committed
901 902
		Support for SMSC's LAN911x and LAN921x chips

903
			CONFIG_SMC911X_BASE
Jens Gehrlein's avatar
Jens Gehrlein committed
904 905 906
			Define this to hold the physical address
			of the device (I/O space)

907
			CONFIG_SMC911X_32_BIT
Jens Gehrlein's avatar
Jens Gehrlein committed
908 909
			Define this if data bus is 32 bits

910
			CONFIG_SMC911X_16_BIT
Jens Gehrlein's avatar
Jens Gehrlein committed
911 912
			Define this if data bus is 16 bits. If your processor
			automatically converts one 32 bit word to two 16 bit
913
			words you may also try CONFIG_SMC911X_32_BIT.
Jens Gehrlein's avatar
Jens Gehrlein committed
914

915 916 917 918 919 920 921 922 923
		CONFIG_SH_ETHER
		Support for Renesas on-chip Ethernet controller

			CONFIG_SH_ETHER_USE_PORT
			Define the number of ports to be used

			CONFIG_SH_ETHER_PHY_ADDR
			Define the ETH PHY's address

924 925 926
			CONFIG_SH_ETHER_CACHE_WRITEBACK
			If this option is set, the driver enables cache flush.

wdenk's avatar
wdenk committed
927 928
- USB Support:
		At the moment only the UHCI host controller is
wdenk's avatar
wdenk committed
929
		supported (PIP405, MIP405, MPC5200); define
wdenk's avatar
wdenk committed
930 931
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
wdenk's avatar
wdenk committed
932
		and define CONFIG_USB_STORAGE to enable the USB
wdenk's avatar
wdenk committed
933 934 935 936
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).
wdenk's avatar
wdenk committed
937 938 939
		MPC5200 USB requires additional defines:
			CONFIG_USB_CLOCK
				for 528 MHz Clock: 0x0001bbbb
940 941
			CONFIG_PSC3_USB
				for USB on PSC3
wdenk's avatar
wdenk committed
942 943 944
			CONFIG_USB_CONFIG
				for differential drivers: 0x00001000
				for single ended drivers: 0x00005000
945 946
				for differential drivers on PSC3: 0x00000100
				for single ended drivers on PSC3: 0x00004100
947
			CONFIG_SYS_USB_EVENT_POLL
Zhang Wei's avatar
Zhang Wei committed
948 949
				May be defined to allow interrupt polling
				instead of using asynchronous interrupts
wdenk's avatar
wdenk committed
950

Wolfgang Denk's avatar
Wolfgang Denk committed
951 952 953 954
- USB Device:
		Define the below if you wish to use the USB console.
		Once firmware is rebuilt from a serial console issue the
		command "setenv stdin usbtty; setenv stdout usbtty" and
955
		attach your USB cable. The Unix command "dmesg" should print
Wolfgang Denk's avatar
Wolfgang Denk committed
956 957
		it has found a new device. The environment variable usbtty
		can be set to gserial or cdc_acm to enable your device to
Wolfgang Denk's avatar
Wolfgang Denk committed
958
		appear to a USB host as a Linux gserial device or a
Wolfgang Denk's avatar
Wolfgang Denk committed
959 960 961 962 963 964 965
		Common Device Class Abstract Control Model serial device.
		If you select usbtty = gserial you should be able to enumerate
		a Linux host by
		# modprobe usbserial vendor=0xVendorID product=0xProductID
		else if using cdc_acm, simply setting the environment
		variable usbtty to be cdc_acm should suffice. The following
		might be defined in YourBoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
966

Wolfgang Denk's avatar
Wolfgang Denk committed
967 968 969 970 971 972
			CONFIG_USB_DEVICE
			Define this to build a UDC device

			CONFIG_USB_TTY
			Define this to have a tty type of device available to
			talk to the UDC device
Wolfgang Denk's avatar
Wolfgang Denk committed
973

974
			CONFIG_SYS_CONSOLE_IS_IN_ENV
Wolfgang Denk's avatar
Wolfgang Denk committed
975 976 977 978
			Define this if you want stdin, stdout &/or stderr to
			be set to usbtty.

			mpc8xx:
979
				CONFIG_SYS_USB_EXTC_CLK 0xBLAH
Wolfgang Denk's avatar
Wolfgang Denk committed
980
				Derive USB clock from external clock "blah"
981
				- CONFIG_SYS_USB_EXTC_CLK 0x02
Wolfgang Denk's avatar
Wolfgang Denk committed
982

983
				CONFIG_SYS_USB_BRG_CLK 0xBLAH
Wolfgang Denk's avatar
Wolfgang Denk committed
984
				Derive USB clock from brgclk
985
				- CONFIG_SYS_USB_BRG_CLK 0x04
Wolfgang Denk's avatar
Wolfgang Denk committed
986

Wolfgang Denk's avatar
Wolfgang Denk committed
987
		If you have a USB-IF assigned VendorID then you may wish to
Wolfgang Denk's avatar
Wolfgang Denk committed
988
		define your own vendor specific values either in BoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
989
		or directly in usbd_vendor_info.h. If you don't define
Wolfgang Denk's avatar
Wolfgang Denk committed
990 991 992 993 994 995 996
		CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
		CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
		should pretend to be a Linux device to it's target host.

			CONFIG_USBD_MANUFACTURER
			Define this string as the name of your company for
			- CONFIG_USBD_MANUFACTURER "my company"
Wolfgang Denk's avatar
Wolfgang Denk committed
997

Wolfgang Denk's avatar
Wolfgang Denk committed
998 999 1000 1001 1002 1003 1004 1005 1006
			CONFIG_USBD_PRODUCT_NAME
			Define this string as the name of your product
			- CONFIG_USBD_PRODUCT_NAME "acme usb device"

			CONFIG_USBD_VENDORID
			Define this as your assigned Vendor ID from the USB
			Implementors Forum. This *must* be a genuine Vendor ID
			to avoid polluting the USB namespace.
			- CONFIG_USBD_VENDORID 0xFFFF
Wolfgang Denk's avatar
Wolfgang Denk committed
1007

Wolfgang Denk's avatar
Wolfgang Denk committed
1008 1009 1010 1011
			CONFIG_USBD_PRODUCTID
			Define this as the unique Product ID
			for your device
			- CONFIG_USBD_PRODUCTID 0xFFFF
wdenk's avatar
wdenk committed
1012

wdenk's avatar
wdenk committed
1013

1014
- MMC Support:
wdenk's avatar
wdenk committed
1015 1016 1017
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
1018
		to physical memory similar to flash. Command line is
1019 1020
		enabled with CONFIG_CMD_MMC. The MMC driver also works with
		the FAT fs. This is enabled with CONFIG_CMD_FAT.
1021

wdenk's avatar
wdenk committed
1022 1023 1024 1025 1026
- Journaling Flash filesystem support:
		CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
		CONFIG_JFFS2_NAND_DEV
		Define these for a default partition on a NAND device

1027 1028
		CONFIG_SYS_JFFS2_FIRST_SECTOR,
		CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
wdenk's avatar
wdenk committed
1029 1030
		Define these for a default partition on a NOR device

1031
		CONFIG_SYS_JFFS_CUSTOM_PART
wdenk's avatar
wdenk committed
1032 1033 1034 1035
		Define this to create an own partition. You have to provide a
		function struct part_info* jffs2_part_info(int part_num)

		If you define only one JFFS2 partition you may also want to
1036
		#define CONFIG_SYS_JFFS_SINGLE_PART	1
wdenk's avatar
wdenk committed
1037 1038 1039
		to disable the command chpart. This is the default when you
		have not defined a custom partition

wdenk's avatar
wdenk committed
1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062
- Keyboard Support:
		CONFIG_ISA_KEYBOARD

		Define this to enable standard (PC-Style) keyboard
		support

		CONFIG_I8042_KBD
		Standard PC keyboard driver with US (is default) and
		GERMAN key layout (switch via environment 'keymap=de') support.
		Export function i8042_kbd_init, i8042_tstc and i8042_getc
		for cfb_console. Supports cursor blinking.

- Video support:
		CONFIG_VIDEO

		Define this to enable video support (for output to
		video).

		CONFIG_VIDEO_CT69000

		Enable Chips & Technologies 69000 Video chip

		CONFIG_VIDEO_SMI_LYNXEM
wdenk's avatar
wdenk committed
1063
		Enable Silicon Motion SMI 712/710/810 Video chip. The
wdenk's avatar
wdenk committed
1064 1065 1066 1067
		video output is selected via environment 'videoout'
		(1 = LCD and 2 = CRT). If videoout is undefined, CRT is
		assumed.

wdenk's avatar
wdenk committed
1068
		For the CT69000 and SMI_LYNXEM drivers, videomode is
1069
		selected via environment 'videomode'. Two different ways
wdenk's avatar
wdenk committed
1070 1071
		are possible:
		- "videomode=num"   'num' is a standard LiLo mode numbers.
wdenk's avatar
wdenk committed
1072
		Following standard modes are supported	(* is default):
wdenk's avatar
wdenk committed
1073 1074 1075 1076 1077 1078 1079 1080

		      Colors	640x480 800x600 1024x768 1152x864 1280x1024
		-------------+---------------------------------------------
		      8 bits |	0x301*	0x303	 0x305	  0x161	    0x307
		     15 bits |	0x310	0x313	 0x316	  0x162	    0x319
		     16 bits |	0x311	0x314	 0x317	  0x163	    0x31A
		     24 bits |	0x312	0x315	 0x318	    ?	    0x31B
		-------------+---------------------------------------------
wdenk's avatar
wdenk committed
1081 1082
		(i.e. setenv videomode 317; saveenv; reset;)

wdenk's avatar
wdenk committed
1083
		- "videomode=bootargs" all the video parameters are parsed
1084
		from the bootargs. (See drivers/video/videomodes.c)
wdenk's avatar
wdenk committed
1085 1086


1087
		CONFIG_VIDEO_SED13806
1088
		Enable Epson SED13806 driver. This driver supports 8bpp
1089 1090 1091
		and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
		or CONFIG_VIDEO_SED13806_16BPP

1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105
		CONFIG_FSL_DIU_FB
		Enable the Freescale DIU video driver.  Reference boards for
		SOCs that have a DIU should define this macro to enable DIU
		support, and should also define these other macros:

			CONFIG_SYS_DIU_ADDR
			CONFIG_VIDEO
			CONFIG_CMD_BMP
			CONFIG_CFB_CONSOLE
			CONFIG_VIDEO_SW_CURSOR
			CONFIG_VGA_AS_SINGLE_DEVICE
			CONFIG_VIDEO_LOGO
			CONFIG_VIDEO_BMP_LOGO

1106 1107 1108 1109
		The DIU driver will look for the 'video-mode' environment
		variable, and if defined, enable the DIU as a console during
		boot.  See the documentation file README.video for a
		description of this variable.
1110

1111
- Keyboard Support:
wdenk's avatar
wdenk committed
1112
		CONFIG_KEYBOARD
1113

wdenk's avatar
wdenk committed
1114 1115 1116 1117
		Define this to enable a custom keyboard support.
		This simply calls drv_keyboard_init() which must be
		defined in your board-specific files.
		The only board using this so far is RBC823.
1118

wdenk's avatar
wdenk committed
1119 1120 1121 1122 1123 1124
- LCD Support:	CONFIG_LCD

		Define this to enable LCD support (for output to LCD
		display); also select one of the supported displays
		by defining one of these:

Stelian Pop's avatar
Stelian Pop committed
1125 1126 1127 1128
		CONFIG_ATMEL_LCD:

			HITACHI TX09D70VM1CCA, 3.5", 240x320.

wdenk's avatar
wdenk committed
1129
		CONFIG_NEC_NL6448AC33:
wdenk's avatar
wdenk committed
1130

wdenk's avatar
wdenk committed
1131
			NEC NL6448AC33-18. Active, color, single scan.
wdenk's avatar
wdenk committed
1132

wdenk's avatar
wdenk committed
1133
		CONFIG_NEC_NL6448BC20
wdenk's avatar
wdenk committed
1134

wdenk's avatar
wdenk committed
1135 1136 1137 1138 1139 1140
			NEC NL6448BC20-08. 6.5", 640x480.
			Active, color, single scan.

		CONFIG_NEC_NL6448BC33_54

			NEC NL6448BC33-54. 10.4", 640x480.
wdenk's avatar
wdenk committed
1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168
			Active, color, single scan.

		CONFIG_SHARP_16x9

			Sharp 320x240. Active, color, single scan.
			It isn't 16x9, and I am not sure what it is.

		CONFIG_SHARP_LQ64D341

			Sharp LQ64D341 display, 640x480.
			Active, color, single scan.

		CONFIG_HLD1045

			HLD1045 display, 640x480.
			Active, color, single scan.

		CONFIG_OPTREX_BW

			Optrex	 CBL50840-2 NF-FW 99 22 M5
			or
			Hitachi	 LMG6912RPFC-00T
			or
			Hitachi	 SP14Q002

			320x240. Black & white.

		Normally display is black on white background; define
1169
		CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
wdenk's avatar
wdenk committed
1170

wdenk's avatar
wdenk committed
1171
- Splash Screen Support: CONFIG_SPLASH_SCREEN
1172

wdenk's avatar
wdenk committed
1173 1174 1175
		If this option is set, the environment is checked for
		a variable "splashimage". If found, the usual display
		of logo, copyright and system information on the LCD
1176
		is suppressed and the BMP image at the address
wdenk's avatar
wdenk committed
1177 1178 1179 1180
		specified in "splashimage" is loaded instead. The
		console is redirected to the "nulldev", too. This
		allows for a "silent" boot where a splash screen is
		loaded very quickly after power-on.
1181

1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201
		CONFIG_SPLASH_SCREEN_ALIGN

		If this option is set the splash image can be freely positioned
		on the screen. Environment variable "splashpos" specifies the
		position as "x,y". If a positive number is given it is used as
		number of pixel from left/top. If a negative number is given it
		is used as number of pixel from right/bottom. You can also
		specify 'm' for centering the image.

		Example:
		setenv splashpos m,m
			=> image at center of screen

		setenv splashpos 30,20
			=> image at x = 30 and y = 20

		setenv splashpos -10,m
			=> vertically centered image
			   at x = dspWidth - bmpWidth - 9

1202 1203 1204 1205 1206 1207
- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP

		If this option is set, additionally to standard BMP
		images, gzipped BMP images can be displayed via the
		splashscreen support or the bmp command.

1208 1209 1210 1211 1212 1213
- Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8

		If this option is set, 8-bit RLE compressed BMP images
		can be displayed via the splashscreen support or the
		bmp command.

wdenk's avatar
wdenk committed
1214 1215 1216 1217 1218 1219 1220
- Compression support:
		CONFIG_BZIP2

		If this option is set, support for bzip2 compressed
		images is included. If not, only uncompressed and gzip
		compressed images are supported.

1221
		NOTE: the bzip2 algorithm requires a lot of RAM, so
1222
		the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1223
		be at least 4MB.
1224

1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245
		CONFIG_LZMA

		If this option is set, support for lzma compressed
		images is included.

		Note: The LZMA algorithm adds between 2 and 4KB of code and it
		requires an amount of dynamic memory that is given by the
		formula:

			(1846 + 768 << (lc + lp)) * sizeof(uint16)

		Where lc and lp stand for, respectively, Literal context bits
		and Literal pos bits.

		This value is upper-bounded by 14MB in the worst case. Anyway,
		for a ~4MB large kernel image, we have lc=3 and lp=0 for a
		total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
		a very small buffer.

		Use the lzmainfo tool to determinate the lc and lp values and
		then calculate the amount of needed dynamic memory (ensuring
1246
		the appropriate CONFIG_SYS_MALLOC_LEN value).
1247

wdenk's avatar
wdenk committed
1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259
- MII/PHY support:
		CONFIG_PHY_ADDR

		The address of PHY on MII bus.

		CONFIG_PHY_CLOCK_FREQ (ppc4xx)

		The clock frequency of the MII bus

		CONFIG_PHY_GIGE

		If this option is set, support for speed/duplex
1260
		detection of gigabit PHY is included.
wdenk's avatar
wdenk committed
1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273

		CONFIG_PHY_RESET_DELAY

		Some PHY like Intel LXT971A need extra delay after
		reset before any MII register access is possible.
		For such PHY, set this option to the usec delay
		required. (minimum 300usec for LXT971A)

		CONFIG_PHY_CMD_DELAY (ppc4xx)

		Some PHY like Intel LXT971A need extra delay after
		command issued before MII status register can be read

wdenk's avatar
wdenk committed
1274 1275
- Ethernet address:
		CONFIG_ETHADDR
1276
		CONFIG_ETH1ADDR
wdenk's avatar
wdenk committed
1277 1278
		CONFIG_ETH2ADDR
		CONFIG_ETH3ADDR
1279 1280
		CONFIG_ETH4ADDR
		CONFIG_ETH5ADDR
wdenk's avatar
wdenk committed
1281

1282 1283
		Define a default value for Ethernet address to use
		for the respective Ethernet interface, in case this
wdenk's avatar
wdenk committed
1284 1285 1286 1287 1288 1289
		is not determined automatically.

- IP address:
		CONFIG_IPADDR

		Define a default value for the IP address to use for
1290
		the default Ethernet interface, in case this is not
wdenk's avatar
wdenk committed
1291 1292 1293 1294 1295
		determined through e.g. bootp.

- Server IP address:
		CONFIG_SERVERIP

1296
		Defines a default value for the IP address of a TFTP
wdenk's avatar
wdenk committed
1297 1298
		server to contact when using the "tftboot" command.

1299 1300 1301 1302 1303
		CONFIG_KEEP_SERVERADDR

		Keeps the server's MAC address, in the env 'serveraddr'
		for passing to bootargs (like Linux's netconsole option)

David Updegraff's avatar
David Updegraff committed
1304 1305 1306 1307 1308
- Multicast TFTP Mode:
		CONFIG_MCAST_TFTP

		Defines whether you want to support multicast TFTP as per
		rfc-2090; for example to work with atftp.  Lets lots of targets
1309
		tftp down the same boot image concurrently.  Note: the Ethernet
David Updegraff's avatar
David Updegraff committed
1310 1311 1312 1313
		driver in use must provide a function: mcast() to join/leave a
		multicast group.

		CONFIG_BOOTP_RANDOM_DELAY
wdenk's avatar
wdenk committed
1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324
- BOOTP Recovery Mode:
		CONFIG_BOOTP_RANDOM_DELAY

		If you have many targets in a network that try to
		boot using BOOTP, you may want to avoid that all
		systems send out BOOTP requests at precisely the same
		moment (which would happen for instance at recovery
		from a power failure, when all systems will try to
		boot, thus flooding the BOOTP server. Defining
		CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
		inserted before sending out BOOTP requests. The
1325
		following delays are inserted then:
wdenk's avatar
wdenk committed
1326 1327 1328 1329 1330 1331 1332

		1st BOOTP request:	delay 0 ... 1 sec
		2nd BOOTP request:	delay 0 ... 2 sec
		3rd BOOTP request:	delay 0 ... 4 sec
		4th and following
		BOOTP requests:		delay 0 ... 8 sec

1333
- DHCP Advanced Options:
1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348
		You can fine tune the DHCP functionality by defining
		CONFIG_BOOTP_* symbols:

		CONFIG_BOOTP_SUBNETMASK
		CONFIG_BOOTP_GATEWAY
		CONFIG_BOOTP_HOSTNAME
		CONFIG_BOOTP_NISDOMAIN
		CONFIG_BOOTP_BOOTPATH
		CONFIG_BOOTP_BOOTFILESIZE
		CONFIG_BOOTP_DNS
		CONFIG_BOOTP_DNS2
		CONFIG_BOOTP_SEND_HOSTNAME
		CONFIG_BOOTP_NTPSERVER
		CONFIG_BOOTP_TIMEOFFSET
		CONFIG_BOOTP_VENDOREX
1349

1350 1351
		CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
		environment variable, not the BOOTP server.
1352 1353 1354 1355 1356 1357 1358 1359

		CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
		serverip from a DHCP server, it is possible that more
		than one DNS serverip is offered to the client.
		If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
		serverip will be stored in the additional environment
		variable "dnsip2". The first DNS serverip is always
		stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1360
		is defined.
1361 1362 1363 1364

		CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
		to do a dynamic update of a DNS server. To do this, they
		need the hostname of the DHCP requester.