README 209 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
2
# (C) Copyright 2000 - 2013
wdenk's avatar
wdenk committed
3 4
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
5
# SPDX-License-Identifier:	GPL-2.0+
wdenk's avatar
wdenk committed
6 7 8 9 10
#

Summary:
========

11
This directory contains the source code for U-Boot, a boot loader for
wdenk's avatar
wdenk committed
12 13 14 15
Embedded boards based on PowerPC, ARM, MIPS and several other
processors, which can be installed in a boot ROM and used to
initialize and test the hardware or to download and run application
code.
wdenk's avatar
wdenk committed
16 17

The development of U-Boot is closely related to Linux: some parts of
18 19
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
20 21 22 23 24 25 26 27 28 29 30 31 32 33
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
34
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
35 36
"working". In fact, many of them are used in production systems.

37
In case of problems see the CHANGELOG and CREDITS files to find out
38
who contributed the specific port. The boards.cfg file lists board
39
maintainers.
wdenk's avatar
wdenk committed
40

41 42 43 44 45
Note: There is no CHANGELOG file in the actual U-Boot source tree;
it can be created dynamically from the Git log using:

	make CHANGELOG

wdenk's avatar
wdenk committed
46 47 48 49

Where to get help:
==================

50 51
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
52 53 54 55
<u-boot@lists.denx.de>. There is also an archive of previous traffic
on the mailing list - please search the archive before asking FAQ's.
Please see http://lists.denx.de/pipermail/u-boot and
http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
wdenk's avatar
wdenk committed
56 57


58 59 60 61 62 63 64 65
Where to get source code:
=========================

The U-Boot source code is maintained in the git repository at
git://www.denx.de/git/u-boot.git ; you can browse it online at
http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary

The "snapshot" links on this page allow you to download tarballs of
66
any version you might be interested in. Official releases are also
67 68 69
available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
directory.

70
Pre-built (and tested) images are available from
71 72 73
ftp://ftp.denx.de/pub/u-boot/images/


wdenk's avatar
wdenk committed
74 75 76 77
Where we come from:
===================

- start from 8xxrom sources
78
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
79 80 81 82 83 84 85
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
86
  * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
87
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
88
- add other CPU families (starting with ARM)
89
- create U-Boot project (http://sourceforge.net/projects/u-boot)
Magnus Lilja's avatar
Magnus Lilja committed
90
- current project page: see http://www.denx.de/wiki/U-Boot
91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
113 114


wdenk's avatar
wdenk committed
115 116 117
Versioning:
===========

118 119 120 121 122 123 124 125
Starting with the release in October 2008, the names of the releases
were changed from numerical release numbers without deeper meaning
into a time stamp based numbering. Regular releases are identified by
names consisting of the calendar year and month of the release date.
Additional fields (if present) indicate release candidates or bug fix
releases in "stable" maintenance trees.

Examples:
Wolfgang Denk's avatar
Wolfgang Denk committed
126
	U-Boot v2009.11	    - Release November 2009
127 128
	U-Boot v2009.11.1   - Release 1 in version November 2009 stable tree
	U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
wdenk's avatar
wdenk committed
129 130


wdenk's avatar
wdenk committed
131 132 133
Directory Hierarchy:
====================

134 135 136 137 138
/arch			Architecture specific files
  /arm			Files generic to ARM architecture
    /cpu		CPU specific files
      /arm720t		Files specific to ARM 720 CPUs
      /arm920t		Files specific to ARM 920 CPUs
139
	/at91		Files specific to Atmel AT91RM9200 CPU
Wolfgang Denk's avatar
Wolfgang Denk committed
140 141
	/imx		Files specific to Freescale MC9328 i.MX CPUs
	/s3c24x0	Files specific to Samsung S3C24X0 CPUs
142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165
      /arm926ejs	Files specific to ARM 926 CPUs
      /arm1136		Files specific to ARM 1136 CPUs
      /pxa		Files specific to Intel XScale PXA CPUs
      /sa1100		Files specific to Intel StrongARM SA1100 CPUs
    /lib		Architecture specific library files
  /avr32		Files generic to AVR32 architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /blackfin		Files generic to Analog Devices Blackfin architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /m68k			Files generic to m68k architecture
    /cpu		CPU specific files
      /mcf52x2		Files specific to Freescale ColdFire MCF52x2 CPUs
      /mcf5227x		Files specific to Freescale ColdFire MCF5227x CPUs
      /mcf532x		Files specific to Freescale ColdFire MCF5329 CPUs
      /mcf5445x		Files specific to Freescale ColdFire MCF5445x CPUs
      /mcf547x_8x	Files specific to Freescale ColdFire MCF547x_8x CPUs
    /lib		Architecture specific library files
  /microblaze		Files generic to microblaze architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
  /mips			Files generic to MIPS architecture
    /cpu		CPU specific files
166
      /mips32		Files specific to MIPS32 CPUs
167
      /xburst		Files specific to Ingenic XBurst CPUs
168
    /lib		Architecture specific library files
169 170 171 172
  /nds32		Files generic to NDS32 architecture
    /cpu		CPU specific files
      /n1213		Files specific to Andes Technology N1213 CPUs
    /lib		Architecture specific library files
173 174 175
  /nios2		Files generic to Altera NIOS2 architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
176 177 178
  /openrisc		Files generic to OpenRISC architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
Stefan Roese's avatar
Stefan Roese committed
179
  /powerpc		Files generic to PowerPC architecture
180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200
    /cpu		CPU specific files
      /74xx_7xx		Files specific to Freescale MPC74xx and 7xx CPUs
      /mpc5xx		Files specific to Freescale MPC5xx CPUs
      /mpc5xxx		Files specific to Freescale MPC5xxx CPUs
      /mpc8xx		Files specific to Freescale MPC8xx CPUs
      /mpc824x		Files specific to Freescale MPC824x CPUs
      /mpc8260		Files specific to Freescale MPC8260 CPUs
      /mpc85xx		Files specific to Freescale MPC85xx CPUs
      /ppc4xx		Files specific to AMCC PowerPC 4xx CPUs
    /lib		Architecture specific library files
  /sh			Files generic to SH architecture
    /cpu		CPU specific files
      /sh2		Files specific to sh2 CPUs
      /sh3		Files specific to sh3 CPUs
      /sh4		Files specific to sh4 CPUs
    /lib		Architecture specific library files
  /sparc		Files generic to SPARC architecture
    /cpu		CPU specific files
      /leon2		Files specific to Gaisler LEON2 SPARC CPU
      /leon3		Files specific to Gaisler LEON3 SPARC CPU
    /lib		Architecture specific library files
201 202 203
  /x86			Files generic to x86 architecture
    /cpu		CPU specific files
    /lib		Architecture specific library files
204 205 206 207 208 209
/api			Machine/arch independent API for external apps
/board			Board dependent files
/common			Misc architecture independent functions
/disk			Code for disk drive partition handling
/doc			Documentation (don't expect too much)
/drivers		Commonly used device drivers
210
/dts			Contains Makefile for building internal U-Boot fdt.
211 212 213 214 215 216 217 218 219
/examples		Example code for standalone applications, etc.
/fs			Filesystem code (cramfs, ext2, jffs2, etc.)
/include		Header Files
/lib			Files generic to all architectures
  /libfdt		Library files to support flattened device trees
  /lzma			Library files to support LZMA decompression
  /lzo			Library files to support LZO decompression
/net			Networking code
/post			Power On Self Test
220
/spl			Secondary Program Loader framework
221
/tools			Tools to build S-Record or U-Boot images, etc.
wdenk's avatar
wdenk committed
222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
238
  "CONFIG_SYS_".
wdenk's avatar
wdenk committed
239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257

Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".

Example: For a TQM823L module type:

	cd u-boot
	make TQM823L_config

258
For the Cogent platform, you need to specify the CPU type as well;
wdenk's avatar
wdenk committed
259 260 261 262 263 264 265 266 267 268 269 270 271 272 273
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.


Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
274 275 276 277 278
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.


wdenk's avatar
wdenk committed
279 280
The following options need to be configured:

281 282 283
- CPU Type:	Define exactly one, e.g. CONFIG_MPC85XX.

- Board Type:	Define exactly one, e.g. CONFIG_MPC8540ADS.
284 285

- CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
286
		Define exactly one, e.g. CONFIG_ATSTK1002
wdenk's avatar
wdenk committed
287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305

- CPU Module Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
		CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
		CONFIG_CMA287_23, CONFIG_CMA287_50

- Motherboard Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA101, CONFIG_CMA102

- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
		Define one or more of
		CONFIG_CMA302

- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
		Define one or more of
		CONFIG_LCD_HEARTBEAT	- update a character position on
306
					  the LCD display every second with
wdenk's avatar
wdenk committed
307 308
					  a "rotator" |\-/|\-/

wdenk's avatar
wdenk committed
309 310 311
- Board flavour: (if CONFIG_MPC8260ADS is defined)
		CONFIG_ADSTYPE
		Possible values are:
312 313 314 315
			CONFIG_SYS_8260ADS	- original MPC8260ADS
			CONFIG_SYS_8266ADS	- MPC8266ADS
			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
			CONFIG_SYS_8272ADS	- MPC8272ADS
wdenk's avatar
wdenk committed
316

317 318 319 320 321
- Marvell Family Member
		CONFIG_SYS_MVFS		- define it if you want to enable
					  multiple fs option at one time
					  for marvell soc family

wdenk's avatar
wdenk committed
322
- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk's avatar
wdenk committed
323 324
		Define exactly one of
		CONFIG_MPC8240, CONFIG_MPC8245
wdenk's avatar
wdenk committed
325

326
- 8xx CPU Options: (if using an MPC8xx CPU)
wdenk's avatar
wdenk committed
327 328
		CONFIG_8xx_GCLK_FREQ	- deprecated: CPU clock if
					  get_gclk_freq() cannot work
wdenk's avatar
wdenk committed
329 330
					  e.g. if there is no 32KHz
					  reference PIT/RTC clock
wdenk's avatar
wdenk committed
331 332
		CONFIG_8xx_OSCLK	- PLL input clock (either EXTCLK
					  or XTAL/EXTAL)
wdenk's avatar
wdenk committed
333

wdenk's avatar
wdenk committed
334
- 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
335 336
		CONFIG_SYS_8xx_CPUCLK_MIN
		CONFIG_SYS_8xx_CPUCLK_MAX
wdenk's avatar
wdenk committed
337
		CONFIG_8xx_CPUCLK_DEFAULT
338 339
			See doc/README.MPC866

340
		CONFIG_SYS_MEASURE_CPUCLK
341

wdenk's avatar
wdenk committed
342 343 344 345 346
		Define this to measure the actual CPU clock instead
		of relying on the correctness of the configured
		values. Mostly useful for board bringup to make sure
		the PLL is locked at the intended frequency. Note
		that this requires a (stable) reference clock (32 kHz
347
		RTC clock or CONFIG_SYS_8XX_XIN)
348

349 350 351 352 353
		CONFIG_SYS_DELAYED_ICACHE

		Define this option if you want to enable the
		ICache only when Code runs from RAM.

354
- 85xx CPU Options:
355 356 357 358 359 360
		CONFIG_SYS_PPC64

		Specifies that the core is a 64-bit PowerPC implementation (implements
		the "64" category of the Power ISA). This is necessary for ePAPR
		compliance, among other possible reasons.

361 362 363 364 365 366
		CONFIG_SYS_FSL_TBCLK_DIV

		Defines the core time base clock divider ratio compared to the
		system clock.  On most PQ3 devices this is 8, on newer QorIQ
		devices it can be 16 or 32.  The ratio varies from SoC to Soc.

367 368 369 370 371
		CONFIG_SYS_FSL_PCIE_COMPAT

		Defines the string to utilize when trying to match PCIe device
		tree nodes for the given platform.

372 373 374 375 376 377 378 379 380
		CONFIG_SYS_PPC_E500_DEBUG_TLB

		Enables a temporary TLB entry to be used during boot to work
		around limitations in e500v1 and e500v2 external debugger
		support. This reduces the portions of the boot code where
		breakpoints and single stepping do not work.  The value of this
		symbol should be set to the TLB1 entry to be used for this
		purpose.

381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400
		CONFIG_SYS_FSL_ERRATUM_A004510

		Enables a workaround for erratum A004510.  If set,
		then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.

		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)

		Defines one or two SoC revisions (low 8 bits of SVR)
		for which the A004510 workaround should be applied.

		The rest of SVR is either not relevant to the decision
		of whether the erratum is present (e.g. p2040 versus
		p2041) or is implied by the build target, which controls
		whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.

		See Freescale App Note 4493 for more information about
		this erratum.

401 402 403 404
		CONFIG_A003399_NOR_WORKAROUND
		Enables a workaround for IFC erratum A003399. It is only
		requred during NOR boot.

405 406 407 408 409
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY

		This is the value to write into CCSR offset 0x18600
		according to the A004510 workaround.

410 411 412 413
		CONFIG_SYS_FSL_DSP_DDR_ADDR
		This value denotes start offset of DDR memory which is
		connected exclusively to the DSP cores.

414 415 416 417
		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
		This value denotes start offset of M2 memory
		which is directly connected to the DSP core.

418 419 420 421
		CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
		This value denotes start offset of M3 memory which is directly
		connected to the DSP core.

422 423 424
		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
		This value denotes start offset of DSP CCSR space.

425 426 427 428 429
		CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
		Single Source Clock is clocking mode present in some of FSL SoC's.
		In this mode, a single differential clock is used to supply
		clocks to the sysclock, ddrclock and usbclock.

430 431 432 433 434 435
- Generic CPU options:
		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN

		Defines the endianess of the CPU. Implementation of those
		values is arch specific.

436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456
		CONFIG_SYS_FSL_DDR
		Freescale DDR driver in use. This type of DDR controller is
		found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
		SoCs.

		CONFIG_SYS_FSL_DDR_ADDR
		Freescale DDR memory-mapped register base.

		CONFIG_SYS_FSL_DDR_EMU
		Specify emulator support for DDR. Some DDR features such as
		deskew training are not available.

		CONFIG_SYS_FSL_DDRC_GEN1
		Freescale DDR1 controller.

		CONFIG_SYS_FSL_DDRC_GEN2
		Freescale DDR2 controller.

		CONFIG_SYS_FSL_DDRC_GEN3
		Freescale DDR3 controller.

457 458 459
		CONFIG_SYS_FSL_DDRC_ARM_GEN3
		Freescale DDR3 controller for ARM-based SoCs.

460 461 462 463 464 465 466 467 468 469 470 471 472 473
		CONFIG_SYS_FSL_DDR1
		Board config to use DDR1. It can be enabled for SoCs with
		Freescale DDR1 or DDR2 controllers, depending on the board
		implemetation.

		CONFIG_SYS_FSL_DDR2
		Board config to use DDR2. It can be eanbeld for SoCs with
		Freescale DDR2 or DDR3 controllers, depending on the board
		implementation.

		CONFIG_SYS_FSL_DDR3
		Board config to use DDR3. It can be enabled for SoCs with
		Freescale DDR3 controllers.

474 475 476 477 478 479
		CONFIG_SYS_FSL_IFC_BE
		Defines the IFC controller register space as Big Endian

		CONFIG_SYS_FSL_IFC_LE
		Defines the IFC controller register space as Little Endian

480 481 482 483 484 485 486 487 488
		CONFIG_SYS_FSL_PBL_PBI
		It enables addition of RCW (Power on reset configuration) in built image.
		Please refer doc/README.pblimage for more details

		CONFIG_SYS_FSL_PBL_RCW
		It adds PBI(pre-boot instructions) commands in u-boot build image.
		PBI commands can be used to configure SoC before it starts the execution.
		Please refer doc/README.pblimage for more details

489 490 491 492 493 494
		CONFIG_SYS_FSL_DDR_BE
		Defines the DDR controller register space as Big Endian

		CONFIG_SYS_FSL_DDR_LE
		Defines the DDR controller register space as Little Endian

495
- Intel Monahans options:
496
		CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
497 498 499 500 501

		Defines the Monahans run mode to oscillator
		ratio. Valid values are 8, 16, 24, 31. The core
		frequency is this value multiplied by 13 MHz.

502
		CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
Wolfgang Denk's avatar
Wolfgang Denk committed
503

504 505
		Defines the Monahans turbo mode to oscillator
		ratio. Valid values are 1 (default if undefined) and
Wolfgang Denk's avatar
Wolfgang Denk committed
506
		2. The core frequency as calculated above is multiplied
507
		by this value.
Wolfgang Denk's avatar
Wolfgang Denk committed
508

509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540
- MIPS CPU options:
		CONFIG_SYS_INIT_SP_OFFSET

		Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
		pointer. This is needed for the temporary stack before
		relocation.

		CONFIG_SYS_MIPS_CACHE_MODE

		Cache operation mode for the MIPS CPU.
		See also arch/mips/include/asm/mipsregs.h.
		Possible values are:
			CONF_CM_CACHABLE_NO_WA
			CONF_CM_CACHABLE_WA
			CONF_CM_UNCACHED
			CONF_CM_CACHABLE_NONCOHERENT
			CONF_CM_CACHABLE_CE
			CONF_CM_CACHABLE_COW
			CONF_CM_CACHABLE_CUW
			CONF_CM_CACHABLE_ACCELERATED

		CONFIG_SYS_XWAY_EBU_BOOTCFG

		Special option for Lantiq XWAY SoCs for booting from NOR flash.
		See also arch/mips/cpu/mips32/start.S.

		CONFIG_XWAY_SWAP_BYTES

		Enable compilation of tools/xway-swap-bytes needed for Lantiq
		XWAY SoCs for booting from NOR flash. The U-Boot image needs to
		be swapped if a flash programmer is used.

541 542 543 544 545 546
- ARM options:
		CONFIG_SYS_EXCEPTION_VECTORS_HIGH

		Select high exception vectors of the ARM core, e.g., do not
		clear the V bit of the c1 register of CP15.

Aneesh V's avatar
Aneesh V committed
547 548 549 550 551 552 553 554
		CONFIG_SYS_THUMB_BUILD

		Use this flag to build U-Boot using the Thumb instruction
		set for ARM architectures. Thumb instruction set provides
		better code density. For ARM architectures that support
		Thumb2 this flag will result in Thumb2 code generated by
		GCC.

555
		CONFIG_ARM_ERRATA_716044
556 557 558 559 560 561 562 563 564 565
		CONFIG_ARM_ERRATA_742230
		CONFIG_ARM_ERRATA_743622
		CONFIG_ARM_ERRATA_751472

		If set, the workarounds for these ARM errata are applied early
		during U-Boot startup. Note that these options force the
		workarounds to be applied; no CPU-type/version detection
		exists, unlike the similar options in the Linux kernel. Do not
		set these options unless they apply!

566 567 568 569 570 571 572
- CPU timer options:
		CONFIG_SYS_HZ

		The frequency of the timer returned by get_timer().
		get_timer() must operate in milliseconds and this CONFIG
		option must be set to 1000.

wdenk's avatar
wdenk committed
573
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
574 575 576 577 578 579 580 581 582 583
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
584
		"clocks_in_mhz=1" is automatically included in the
wdenk's avatar
wdenk committed
585 586
		default environment.

wdenk's avatar
wdenk committed
587 588
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

589
		When transferring memsize parameter to linux, some versions
wdenk's avatar
wdenk committed
590 591 592
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

593
		CONFIG_OF_LIBFDT
594 595

		New kernel versions are expecting firmware settings to be
596 597 598 599 600 601
		passed using flattened device trees (based on open firmware
		concepts).

		CONFIG_OF_LIBFDT
		 * New libfdt-based support
		 * Adds the "fdt" command
602
		 * The bootm command automatically updates the fdt
603

604 605 606 607
		OF_CPU - The proper name of the cpus node (only required for
			MPC512X and MPC5xxx based boards).
		OF_SOC - The proper name of the soc node (only required for
			MPC512X and MPC5xxx based boards).
608
		OF_TBCLK - The timebase frequency.
Kumar Gala's avatar
Kumar Gala committed
609
		OF_STDOUT_PATH - The path to the console device
610

611 612
		boards with QUICC Engines require OF_QE to set UCC MAC
		addresses
613

614 615 616 617
		CONFIG_OF_BOARD_SETUP

		Board code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel
618

619 620
		CONFIG_OF_BOOT_CPU

621
		This define fills in the correct boot CPU in the boot
622 623
		param header, the default value is zero if undefined.

624 625 626 627 628 629 630 631 632
		CONFIG_OF_IDE_FIXUP

		U-Boot can detect if an IDE device is present or not.
		If not, and this new config option is activated, U-Boot
		removes the ATA node from the DTS before booting Linux,
		so the Linux IDE driver does not probe the device and
		crash. This is needed for buggy hardware (uc101) where
		no pull down resistor is connected to the signal IDE5V_DD7.

633 634 635 636 637 638 639 640 641 642
		CONFIG_MACH_TYPE	[relevant for ARM only][mandatory]

		This setting is mandatory for all boards that have only one
		machine type and must be used to specify the machine type
		number as it appears in the ARM machine registry
		(see http://www.arm.linux.org.uk/developer/machines/).
		Only boards that have multiple machine types supported
		in a single configuration file and the machine type is
		runtime discoverable, do not have to use this setting.

643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660
- vxWorks boot parameters:

		bootvx constructs a valid bootline using the following
		environments variables: bootfile, ipaddr, serverip, hostname.
		It loads the vxWorks image pointed bootfile.

		CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
		CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
		CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
		CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters

		CONFIG_SYS_VXWORKS_ADD_PARAMS

		Add it at the end of the bootline. E.g "u=username pw=secret"

		Note: If a "bootargs" environment is defined, it will overwride
		the defaults discussed just above.

661 662 663 664 665
- Cache Configuration:
		CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
		CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
		CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot

Aneesh V's avatar
Aneesh V committed
666 667 668 669 670 671
- Cache Configuration for ARM:
		CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
				      controller
		CONFIG_SYS_PL310_BASE - Physical base address of PL310
					controller register space

wdenk's avatar
wdenk committed
672
- Serial Ports:
673
		CONFIG_PL010_SERIAL
wdenk's avatar
wdenk committed
674 675 676

		Define this if you want support for Amba PrimeCell PL010 UARTs.

677
		CONFIG_PL011_SERIAL
wdenk's avatar
wdenk committed
678 679 680 681 682 683 684 685 686 687 688 689 690 691

		Define this if you want support for Amba PrimeCell PL011 UARTs.

		CONFIG_PL011_CLOCK

		If you have Amba PrimeCell PL011 UARTs, set this variable to
		the clock speed of the UARTs.

		CONFIG_PL01x_PORTS

		If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
		define this to a list of base addresses for each (supported)
		port. See e.g. include/configs/versatile.h

692 693 694 695 696 697 698 699 700 701 702 703
		CONFIG_PL011_SERIAL_RLCR

		Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
		have separate receive and transmit line control registers.  Set
		this variable to initialize the extra register.

		CONFIG_PL011_SERIAL_FLUSH_ON_INIT

		On some platforms (e.g. U8500) U-Boot is loaded by a second stage
		boot loader that has already initialized the UART.  Define this
		variable to flush the UART at init time.

wdenk's avatar
wdenk committed
704

wdenk's avatar
wdenk committed
705
- Console Interface:
706 707 708 709
		Depending on board, define exactly one serial port
		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
		CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
		console by defining CONFIG_8xx_CONS_NONE
wdenk's avatar
wdenk committed
710 711 712 713 714 715 716

		Note: if CONFIG_8xx_CONS_NONE is defined, the serial
		port routines must be defined elsewhere
		(i.e. serial_init(), serial_getc(), ...)

		CONFIG_CFB_CONSOLE
		Enables console device for a color framebuffer. Needs following
717
		defines (cf. smiLynxEM, i8042)
wdenk's avatar
wdenk committed
718 719 720 721 722 723 724 725 726
			VIDEO_FB_LITTLE_ENDIAN	graphic memory organisation
						(default big endian)
			VIDEO_HW_RECTFILL	graphic chip supports
						rectangle fill
						(cf. smiLynxEM)
			VIDEO_HW_BITBLT		graphic chip supports
						bit-blit (cf. smiLynxEM)
			VIDEO_VISIBLE_COLS	visible pixel columns
						(cols=pitch)
wdenk's avatar
wdenk committed
727 728
			VIDEO_VISIBLE_ROWS	visible pixel rows
			VIDEO_PIXEL_SIZE	bytes per pixel
wdenk's avatar
wdenk committed
729 730
			VIDEO_DATA_FORMAT	graphic data format
						(0-5, cf. cfb_console.c)
wdenk's avatar
wdenk committed
731
			VIDEO_FB_ADRS		framebuffer address
wdenk's avatar
wdenk committed
732 733 734 735 736 737 738 739 740
			VIDEO_KBD_INIT_FCT	keyboard int fct
						(i.e. i8042_kbd_init())
			VIDEO_TSTC_FCT		test char fct
						(i.e. i8042_tstc)
			VIDEO_GETC_FCT		get char fct
						(i.e. i8042_getc)
			CONFIG_CONSOLE_CURSOR	cursor drawing on/off
						(requires blink timer
						cf. i8042.c)
741
			CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
wdenk's avatar
wdenk committed
742 743
			CONFIG_CONSOLE_TIME	display time/date info in
						upper right corner
744
						(requires CONFIG_CMD_DATE)
wdenk's avatar
wdenk committed
745 746
			CONFIG_VIDEO_LOGO	display Linux logo in
						upper left corner
747 748 749
			CONFIG_VIDEO_BMP_LOGO	use bmp_logo.h instead of
						linux_logo.h for logo.
						Requires CONFIG_VIDEO_LOGO
wdenk's avatar
wdenk committed
750
			CONFIG_CONSOLE_EXTRA_INFO
751
						additional board info beside
wdenk's avatar
wdenk committed
752 753
						the logo

754 755 756 757
		When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
		a limited number of ANSI escape sequences (cursor control,
		erase functions and limited graphics rendition control).

758 759 760
		When CONFIG_CFB_CONSOLE is defined, video console is
		default i/o. Serial console can be forced with
		environment 'console=serial'.
wdenk's avatar
wdenk committed
761

wdenk's avatar
wdenk committed
762 763 764 765
		When CONFIG_SILENT_CONSOLE is defined, all console
		messages (by U-Boot and Linux!) can be silenced with
		the "silent" environment variable. See
		doc/README.silent for more information.
wdenk's avatar
wdenk committed
766

767 768 769 770 771
		CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
			is 0x00.
		CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
			is 0xa0.

wdenk's avatar
wdenk committed
772 773 774
- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
775 776
		CONFIG_SYS_BAUDRATE_TABLE, see below.
		CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
wdenk's avatar
wdenk committed
777

778 779 780
- Console Rx buffer length
		With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
		the maximum receive buffer length for the SMC.
781
		This option is actual only for 82xx and 8xx possible.
782 783 784 785
		If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
		must be defined, to setup the maximum idle timeout for
		the SMC.

786
- Pre-Console Buffer:
787 788 789 790 791 792 793
		Prior to the console being initialised (i.e. serial UART
		initialised etc) all console output is silently discarded.
		Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
		buffer any console messages prior to the console being
		initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
		bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
		a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
Wolfgang Denk's avatar
Wolfgang Denk committed
794
		bytes are output before the console is initialised, the
795 796 797 798
		earlier bytes are discarded.

		'Sane' compilers will generate smaller code if
		CONFIG_PRE_CON_BUF_SZ is a power of 2
799

800 801 802 803 804 805 806 807 808
- Safe printf() functions
		Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
		the printf() functions. These are defined in
		include/vsprintf.h and include snprintf(), vsnprintf() and
		so on. Code size increase is approximately 300-500 bytes.
		If this option is not given then these functions will
		silently discard their buffer size argument - this means
		you are not getting any overflow checking in this case.

wdenk's avatar
wdenk committed
809 810 811
- Boot Delay:	CONFIG_BOOTDELAY - in seconds
		Delay before automatically booting the default image;
		set to -1 to disable autoboot.
812 813
		set to -2 to autoboot with no delay and not check for abort
		(even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
wdenk's avatar
wdenk committed
814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835

		See doc/README.autoboot for these options that
		work with CONFIG_BOOTDELAY. None are required.
		CONFIG_BOOT_RETRY_TIME
		CONFIG_BOOT_RETRY_MIN
		CONFIG_AUTOBOOT_KEYED
		CONFIG_AUTOBOOT_PROMPT
		CONFIG_AUTOBOOT_DELAY_STR
		CONFIG_AUTOBOOT_STOP_STR
		CONFIG_AUTOBOOT_DELAY_STR2
		CONFIG_AUTOBOOT_STOP_STR2
		CONFIG_ZERO_BOOTDELAY_CHECK
		CONFIG_RESET_TO_RETRY

- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_BOOTARGS
836 837 838
		This can be used to pass arguments to the bootm
		command. The value of CONFIG_BOOTARGS goes into the
		environment value "bootargs".
wdenk's avatar
wdenk committed
839 840

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
841 842 843
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
844
		RAM and NFS.
wdenk's avatar
wdenk committed
845

846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861
- Bootcount:
		CONFIG_BOOTCOUNT_LIMIT
		Implements a mechanism for detecting a repeating reboot
		cycle, see:
		http://www.denx.de/wiki/view/DULG/UBootBootCountLimit

		CONFIG_BOOTCOUNT_ENV
		If no softreset save registers are found on the hardware
		"bootcount" is stored in the environment. To prevent a
		saveenv on all reboots, the environment variable
		"upgrade_available" is used. If "upgrade_available" is
		0, "bootcount" is always 0, if "upgrade_available" is
		1 "bootcount" is incremented in the environment.
		So the Userspace Applikation must set the "upgrade_available"
		and "bootcount" variable to 0, if a boot was successfully.

wdenk's avatar
wdenk committed
862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886
- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

887
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
wdenk's avatar
wdenk committed
888 889
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
890
		CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
891 892

- Monitor Functions:
893 894
		Monitor commands can be included or excluded
		from the build by using the #include files
895 896
		<config_cmd_all.h> and #undef'ing unwanted
		commands, or using <config_cmd_default.h>
897 898 899 900 901 902 903 904 905 906 907 908 909
		and augmenting with additional #define's
		for wanted commands.

		The default command configuration includes all commands
		except those marked below with a "*".

		CONFIG_CMD_ASKENV	* ask for env variable
		CONFIG_CMD_BDI		  bdinfo
		CONFIG_CMD_BEDBUG	* Include BedBug Debugger
		CONFIG_CMD_BMP		* BMP support
		CONFIG_CMD_BSP		* Board specific commands
		CONFIG_CMD_BOOTD	  bootd
		CONFIG_CMD_CACHE	* icache, dcache
Michal Simek's avatar
Michal Simek committed
910
		CONFIG_CMD_CLK   	* clock command support
911
		CONFIG_CMD_CONSOLE	  coninfo
Mike Frysinger's avatar
Mike Frysinger committed
912
		CONFIG_CMD_CRC32	* crc32
913 914 915
		CONFIG_CMD_DATE		* support for RTC, date/time...
		CONFIG_CMD_DHCP		* DHCP support
		CONFIG_CMD_DIAG		* Diagnostics
916 917 918 919
		CONFIG_CMD_DS4510	* ds4510 I2C gpio commands
		CONFIG_CMD_DS4510_INFO	* ds4510 I2C info command
		CONFIG_CMD_DS4510_MEM	* ds4510 I2C eeprom/sram commansd
		CONFIG_CMD_DS4510_RST	* ds4510 I2C rst command
920 921
		CONFIG_CMD_DTT		* Digital Therm and Thermostat
		CONFIG_CMD_ECHO		  echo arguments
Peter Tyser's avatar
Peter Tyser committed
922
		CONFIG_CMD_EDITENV	  edit env variable
923 924
		CONFIG_CMD_EEPROM	* EEPROM read/write support
		CONFIG_CMD_ELF		* bootelf, bootvx
925
		CONFIG_CMD_ENV_CALLBACK	* display details about env callbacks
926
		CONFIG_CMD_ENV_FLAGS	* display details about env flags
927
		CONFIG_CMD_ENV_EXISTS	* check existence of env variable
928
		CONFIG_CMD_EXPORTENV	* export the environment
929 930
		CONFIG_CMD_EXT2		* ext2 command support
		CONFIG_CMD_EXT4		* ext4 command support
931 932
		CONFIG_CMD_FS_GENERIC	* filesystem commands (e.g. load, ls)
					  that work for multiple fs types
933
		CONFIG_CMD_SAVEENV	  saveenv
934
		CONFIG_CMD_FDC		* Floppy Disk Support
935
		CONFIG_CMD_FAT		* FAT command support
936 937
		CONFIG_CMD_FLASH	  flinfo, erase, protect
		CONFIG_CMD_FPGA		  FPGA device initialization support
938
		CONFIG_CMD_FUSE		* Device fuse support
Anton Staaf's avatar
Anton Staaf committed
939
		CONFIG_CMD_GETTIME	* Get time since boot
Mike Frysinger's avatar
Mike Frysinger committed
940
		CONFIG_CMD_GO		* the 'go' command (exec code)
Kim Phillips's avatar
Kim Phillips committed
941
		CONFIG_CMD_GREPENV	* search environment
942
		CONFIG_CMD_HASH		* calculate hash / digest
943 944 945 946
		CONFIG_CMD_HWFLOW	* RTS/CTS hw flow control
		CONFIG_CMD_I2C		* I2C serial bus support
		CONFIG_CMD_IDE		* IDE harddisk support
		CONFIG_CMD_IMI		  iminfo
947
		CONFIG_CMD_IMLS		  List all images found in NOR flash
948
		CONFIG_CMD_IMLS_NAND	* List all images found in NAND flash
949
		CONFIG_CMD_IMMAP	* IMMR dump support
950
		CONFIG_CMD_IMPORTENV	* import an environment
Joe Hershberger's avatar
Joe Hershberger committed
951
		CONFIG_CMD_INI		* import data from an ini file into the env
952 953 954 955
		CONFIG_CMD_IRQ		* irqinfo
		CONFIG_CMD_ITEST	  Integer/string test of 2 values
		CONFIG_CMD_JFFS2	* JFFS2 Support
		CONFIG_CMD_KGDB		* kgdb
956
		CONFIG_CMD_LDRINFO	* ldrinfo (display Blackfin loader)
957 958
		CONFIG_CMD_LINK_LOCAL	* link-local IP address auto-configuration
					  (169.254.*.*)
959 960
		CONFIG_CMD_LOADB	  loadb
		CONFIG_CMD_LOADS	  loads
961
		CONFIG_CMD_MD5SUM	* print md5 message digest
Robin Getz's avatar
Robin Getz committed
962
					  (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
963
		CONFIG_CMD_MEMINFO	* Display detailed memory information
964
		CONFIG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
965
					  loop, loopw
966
		CONFIG_CMD_MEMTEST	* mtest
967 968 969
		CONFIG_CMD_MISC		  Misc functions like sleep etc
		CONFIG_CMD_MMC		* MMC memory mapped support
		CONFIG_CMD_MII		* MII utility commands
970
		CONFIG_CMD_MTDPARTS	* MTD partition support
971 972
		CONFIG_CMD_NAND		* NAND support
		CONFIG_CMD_NET		  bootp, tftpboot, rarpboot
973
		CONFIG_CMD_NFS		  NFS support
974
		CONFIG_CMD_PCA953X	* PCA953x I2C gpio commands
Wolfgang Denk's avatar
Wolfgang Denk committed
975
		CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
976 977 978 979 980
		CONFIG_CMD_PCI		* pciinfo
		CONFIG_CMD_PCMCIA		* PCMCIA support
		CONFIG_CMD_PING		* send ICMP ECHO_REQUEST to network
					  host
		CONFIG_CMD_PORTIO	* Port I/O
981
		CONFIG_CMD_READ		* Read raw data from partition
982 983
		CONFIG_CMD_REGINFO	* Register dump
		CONFIG_CMD_RUN		  run command in env variable
984
		CONFIG_CMD_SANDBOX	* sb command to access sandbox features
985 986 987 988 989 990
		CONFIG_CMD_SAVES	* save S record dump
		CONFIG_CMD_SCSI		* SCSI Support
		CONFIG_CMD_SDRAM	* print SDRAM configuration information
					  (requires CONFIG_CMD_I2C)
		CONFIG_CMD_SETGETDCR	  Support for DCR Register access
					  (4xx only)
991
		CONFIG_CMD_SF		* Read/write/erase SPI NOR flash
992
		CONFIG_CMD_SHA1SUM	* print sha1 memory digest
Robin Getz's avatar
Robin Getz committed
993
					  (requires CONFIG_CMD_MEMORY)
994
		CONFIG_CMD_SOFTSWITCH	* Soft switch setting command for BF60x
995
		CONFIG_CMD_SOURCE	  "source" command Support
996
		CONFIG_CMD_SPI		* SPI serial bus support
Luca Ceresoli's avatar
Luca Ceresoli committed
997
		CONFIG_CMD_TFTPSRV	* TFTP transfer in server mode
998
		CONFIG_CMD_TFTPPUT	* TFTP put command (upload)
999 1000
		CONFIG_CMD_TIME		* run command and report execution time (ARM specific)
		CONFIG_CMD_TIMER	* access to the system tick timer
1001 1002
		CONFIG_CMD_USB		* USB support
		CONFIG_CMD_CDP		* Cisco Discover Protocol support
1003
		CONFIG_CMD_MFSL		* Microblaze FSL support
1004
		CONFIG_CMD_XIMG		  Load part of Multi Image
1005

wdenk's avatar
wdenk committed
1006 1007 1008 1009

		EXAMPLE: If you want all functions except of network
		support you can write:

1010 1011
		#include "config_cmd_all.h"
		#undef CONFIG_CMD_NET
wdenk's avatar
wdenk committed
1012

1013 1014
	Other Commands:
		fdt (flattened device tree) command: CONFIG_OF_LIBFDT
wdenk's avatar
wdenk committed
1015 1016

	Note:	Don't enable the "icache" and "dcache" commands
1017
		(configuration option CONFIG_CMD_CACHE) unless you know
1018 1019 1020 1021 1022 1023
		what you (and your U-Boot users) are doing. Data
		cache cannot be enabled on systems like the 8xx or
		8260 (where accesses to the IMMR region must be
		uncached), and it cannot be disabled on all other
		systems where we (mis-) use the data cache to hold an
		initial stack and some data.
wdenk's avatar
wdenk committed
1024 1025 1026 1027


		XXX - this list needs to get updated!

1028 1029
- Regular expression support:
		CONFIG_REGEX
1030 1031 1032 1033
		If this variable is defined, U-Boot is linked against
		the SLRE (Super Light Regular Expression) library,
		which adds regex support to some commands, as for
		example "env grep" and "setexpr".
1034

1035 1036 1037 1038 1039 1040 1041 1042
- Device tree:
		CONFIG_OF_CONTROL
		If this variable is defined, U-Boot will use a device tree
		to configure its devices, instead of relying on statically
		compiled #defines in the board file. This option is
		experimental and only available on a few boards. The device
		tree is available in the global data as gd->fdt_blob.

1043 1044
		U-Boot needs to get its device tree from somewhere. This can
		be done using one of the two options below:
1045 1046 1047 1048 1049 1050 1051

		CONFIG_OF_EMBED
		If this variable is defined, U-Boot will embed a device tree
		binary in its image. This device tree file should be in the
		board directory and called <soc>-<board>.dts. The binary file
		is then picked up in board_init_f() and made available through
		the global data structure as gd->blob.
1052

1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064
		CONFIG_OF_SEPARATE
		If this variable is defined, U-Boot will build a device tree
		binary. It will be called u-boot.dtb. Architecture-specific
		code will locate it at run-time. Generally this works by:

			cat u-boot.bin u-boot.dtb >image.bin

		and in fact, U-Boot does this for you, creating a file called
		u-boot-dtb.bin which is useful in the common case. You can
		still use the individual files if you need something more
		exotic.

wdenk's avatar
wdenk committed
1065 1066 1067
- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078
		support for the SoC. There must be support in the SoC
		specific code for a watchdog. For the 8xx and 8260
		CPUs, the SIU Watchdog feature is enabled in the SYPCR
		register.  When supported for a specific SoC is
		available, then no further board specific code should
		be needed to use it.

		CONFIG_HW_WATCHDOG
		When using a watchdog circuitry external to the used
		SoC, then define this variable and provide board
		specific code for the "hw_watchdog_reset" function.
wdenk's avatar
wdenk committed
1079

1080 1081 1082 1083 1084
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
1085 1086
		Any change to this variable will be reverted at the
		next reset.
1087

wdenk's avatar
wdenk committed
1088 1089
- Real-Time Clock:

1090
		When CONFIG_CMD_DATE is selected, the type of the RTC
wdenk's avatar
wdenk committed
1091 1092 1093 1094 1095
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_MPC8xx	- use internal RTC of MPC8xx
		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
1096
		CONFIG_RTC_MC13XXX	- use MC13783 or MC13892 RTC
wdenk's avatar
wdenk committed
1097
		CONFIG_RTC_MC146818	- use MC146818 RTC
wdenk's avatar
wdenk committed
1098
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
1099
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
1100
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
wdenk's avatar
wdenk committed
1101
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
1102
		CONFIG_RTC_ISL1208	- use Intersil ISL1208 RTC
wdenk's avatar
wdenk committed
1103
		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
1104
		CONFIG_SYS_RTC_DS1337_NOOSC	- Turn off the OSC output for DS1337
1105 1106
		CONFIG_SYS_RV3029_TCR	- enable trickle charger on
					  RV3029 RTC.
wdenk's avatar
wdenk committed
1107

wdenk's avatar
wdenk committed
1108 1109 1110
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

1111 1112 1113
- GPIO Support:
		CONFIG_PCA953X		- use NXP's PCA953X series I2C GPIO

1114 1115 1116 1117
		The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
		chip-ngpio pairs that tell the PCA953X driver the number of
		pins supported by a particular chip.

1118 1119 1120
		Note that if the GPIO device uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

wdenk's avatar
wdenk committed
1121 1122
- Timestamp Support:

1123 1124 1125
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
1126
		automatically enabled when you select CONFIG_CMD_DATE .
wdenk's avatar
wdenk committed
1127

1128 1129 1130 1131 1132 1133 1134 1135 1136 1137
- Partition Labels (disklabels) Supported:
		Zero or more of the following:
		CONFIG_MAC_PARTITION   Apple's MacOS partition table.
		CONFIG_DOS_PARTITION   MS Dos partition table, traditional on the
				       Intel architecture, USB sticks, etc.
		CONFIG_ISO_PARTITION   ISO partition table, used on CDROM etc.
		CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
				       bootloader.  Note 2TB partition limit; see
				       disk/part_efi.c
		CONFIG_MTD_PARTITIONS  Memory Technology Device partition table.
wdenk's avatar
wdenk committed
1138

1139 1140
		If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
		CONFIG_CMD_SCSI) you must configure support for at
1141
		least one non-MTD partition type as well.
wdenk's avatar
wdenk committed
1142 1143

- IDE Reset method:
wdenk's avatar
wdenk committed
1144 1145
		CONFIG_IDE_RESET_ROUTINE - this is defined in several
		board configurations files but used nowhere!
wdenk's avatar
wdenk committed
1146

wdenk's avatar
wdenk committed
1147 1148 1149 1150
		CONFIG_IDE_RESET - is this is defined, IDE Reset will
		be performed by calling the function
			ide_set_reset(int reset)
		which has to be defined in a board specific file
wdenk's avatar
wdenk committed
1151 1152 1153 1154 1155 1156

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

1157 1158 1159 1160
- LBA48 Support
		CONFIG_LBA48

		Set this to enable support for disks larger than 137GB
1161
		Also look at CONFIG_SYS_64BIT_LBA.
1162 1163 1164
		Whithout these , LBA48 support uses 32bit variables and will 'only'
		support disks up to 2.1TB.

1165
		CONFIG_SYS_64BIT_LBA:
1166 1167 1168
			When enabled, makes the IDE subsystem use 64bit sector addresses.
			Default is 32bit.

wdenk's avatar
wdenk committed
1169 1170 1171 1172 1173
- SCSI Support:
		At the moment only there is only support for the
		SYM53C8XX SCSI controller; define
		CONFIG_SCSI_SYM53C8XX to enable it.

1174 1175 1176
		CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
		CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
		CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
wdenk's avatar
wdenk committed
1177 1178
		maximum numbers of LUNs, SCSI ID's and target
		devices.
1179
		CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
wdenk's avatar
wdenk committed
1180

1181 1182
		The environment variable 'scsidevs' is set to the number of
		SCSI devices found during the last scan.
1183

wdenk's avatar
wdenk committed
1184
- NETWORK Support (PCI):
1185
		CONFIG_E1000
1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199
		Support for Intel 8254x/8257x gigabit chips.

		CONFIG_E1000_SPI
		Utility code for direct access to the SPI bus on Intel 8257x.
		This does not do anything useful unless you set at least one
		of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.

		CONFIG_E1000_SPI_GENERIC
		Allow generic access to the SPI bus on the Intel 8257x, for
		example with the "sspi" command.

		CONFIG_CMD_E1000
		Management command for E1000 devices.  When used on devices
		with SPI support you can reprogram the EEPROM from U-Boot.
stroese's avatar
stroese committed
1200

Andre Schwarz's avatar
Andre Schwarz committed
1201
		CONFIG_E1000_FALLBACK_MAC
1202
		default MAC for empty EEPROM after production.
Andre Schwarz's avatar
Andre Schwarz committed
1203

wdenk's avatar
wdenk committed
1204 1205
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
1206
		Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
wdenk's avatar
wdenk committed
1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

wdenk's avatar
wdenk committed
1220 1221
- NETWORK Support (other):

1222 1223 1224 1225 1226 1227 1228 1229 1230 1231
		CONFIG_DRIVER_AT91EMAC
		Support for AT91RM9200 EMAC.

			CONFIG_RMII
			Define this to use reduced MII inteface

			CONFIG_DRIVER_AT91EMAC_QUIET
			If this defined, the driver is quiet.
			The driver doen't show link status messages.

Rob Herring's avatar
Rob Herring committed
1232 1233 1234
		CONFIG_CALXEDA_XGMAC
		Support for the Calxeda XGMAC device

1235
		CONFIG_LAN91C96
wdenk's avatar
wdenk committed
1236 1237 1238 1239 1240 1241 1242 1243 1244
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_BASE
			Define this to hold the physical address
			of the LAN91C96's I/O space

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

1245
		CONFIG_SMC91111
wdenk's avatar
wdenk committed
1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258
		Support for SMSC's LAN91C111 chip

			CONFIG_SMC91111_BASE
			Define this to hold the physical address
			of the device (I/O space)

			CONFIG_SMC_USE_32_BIT
			Define this if data bus is 32 bits

			CONFIG_SMC_USE_IOFUNCS
			Define this to use i/o functions instead of macros
			(some hardware wont work with macros)

1259 1260 1261 1262 1263 1264
		CONFIG_DRIVER_TI_EMAC
		Support for davinci emac

			CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
			Define this if you have more then 3 PHYs.

1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276
		CONFIG_FTGMAC100
		Support for Faraday's FTGMAC100 Gigabit SoC Ethernet

			CONFIG_FTGMAC100_EGIGA
			Define this to use GE link update with gigabit PHY.
			Define this if FTGMAC100 is connected to gigabit PHY.
			If your system has 10/100 PHY only, it might not occur
			wrong behavior. Because PHY usually return timeout or
			useless data when polling gigabit status and gigabit
			control registers. This behavior won't affect the
			correctnessof 10/100 link speed update.

1277
		CONFIG_SMC911X
Jens Gehrlein's avatar
Jens Gehrlein committed
1278 1279
		Support for SMSC's LAN911x and LAN921x chips

1280
			CONFIG_SMC911X_BASE
Jens Gehrlein's avatar
Jens Gehrlein committed
1281 1282 1283
			Define this to hold the physical address
			of the device (I/O space)

1284
			CONFIG_SMC911X_32_BIT
Jens Gehrlein's avatar
Jens Gehrlein committed
1285 1286
			Define this if data bus is 32 bits

1287
			CONFIG_SMC911X_16_BIT
Jens Gehrlein's avatar
Jens Gehrlein committed
1288 1289
			Define this if data bus is 16 bits. If your processor
			automatically converts one 32 bit word to two 16 bit
1290
			words you may also try CONFIG_SMC911X_32_BIT.
Jens Gehrlein's avatar
Jens Gehrlein committed
1291

1292 1293 1294 1295 1296 1297 1298 1299 1300
		CONFIG_SH_ETHER
		Support for Renesas on-chip Ethernet controller

			CONFIG_SH_ETHER_USE_PORT
			Define the number of ports to be used

			CONFIG_SH_ETHER_PHY_ADDR
			Define the ETH PHY's address

1301 1302 1303
			CONFIG_SH_ETHER_CACHE_WRITEBACK
			If this option is set, the driver enables cache flush.

1304
- TPM Support:
1305 1306 1307
		CONFIG_TPM
		Support TPM devices.

1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320
		CONFIG_TPM_TIS_I2C
		Support for i2c bus TPM devices. Only one device
		per system is supported at this time.

			CONFIG_TPM_TIS_I2C_BUS_NUMBER
			Define the the i2c bus number for the TPM device

			CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
			Define the TPM's address on the i2c bus

			CONFIG_TPM_TIS_I2C_BURST_LIMITATION
			Define the burst count bytes upper limit

Dirk Eibach's avatar
Dirk Eibach committed
1321 1322 1323
		CONFIG_TPM_ATMEL_TWI
		Support for Atmel TWI TPM device. Requires I2C support.

1324
		CONFIG_TPM_TIS_LPC
1325 1326 1327 1328 1329 1330 1331 1332
		Support for generic parallel port TPM devices. Only one device
		per system is supported at this time.

			CONFIG_TPM_TIS_BASE_ADDRESS
			Base address where the generic TPM device is mapped
			to. Contemporary x86 systems usually map it at
			0xfed40000.

1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346
		CONFIG_CMD_TPM
		Add tpm monitor functions.
		Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
		provides monitor access to authorized functions.

		CONFIG_TPM
		Define this to enable the TPM support library which provides
		functional interfaces to some TPM commands.
		Requires support for a TPM device.

		CONFIG_TPM_AUTH_SESSIONS
		Define this to enable authorized functions in the TPM library.
		Requires CONFIG_TPM and CONFIG_SHA1.

wdenk's avatar
wdenk committed
1347 1348
- USB Support:
		At the moment only the UHCI host controller is
wdenk's avatar
wdenk committed
1349
		supported (PIP405, MIP405, MPC5200); define
wdenk's avatar
wdenk committed
1350 1351
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
wdenk's avatar
wdenk committed
1352
		and define CONFIG_USB_STORAGE to enable the USB
wdenk's avatar
wdenk committed
1353 1354 1355 1356
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).
wdenk's avatar
wdenk committed
1357 1358 1359
		MPC5200 USB requires additional defines:
			CONFIG_USB_CLOCK
				for 528 MHz Clock: 0x0001bbbb
1360 1361
			CONFIG_PSC3_USB
				for USB on PSC3
wdenk's avatar
wdenk committed
1362 1363 1364
			CONFIG_USB_CONFIG
				for differential drivers: 0x00001000
				for single ended drivers: 0x00005000
1365 1366
				for differential drivers on PSC3: 0x00000100
				for single ended drivers on PSC3: 0x00004100
1367
			CONFIG_SYS_USB_EVENT_POLL
Zhang Wei's avatar
Zhang Wei committed
1368 1369
				May be defined to allow interrupt polling
				instead of using asynchronous interrupts
wdenk's avatar
wdenk committed
1370

1371 1372 1373
		CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
		txfilltuning field in the EHCI controller on reset.

1374 1375 1376
		CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
		interval for usb hub power-on delay.(minimum 100msec)

Wolfgang Denk's avatar
Wolfgang Denk committed
1377 1378 1379 1380
- USB Device:
		Define the below if you wish to use the USB console.
		Once firmware is rebuilt from a serial console issue the
		command "setenv stdin usbtty; setenv stdout usbtty" and
1381
		attach your USB cable. The Unix command "dmesg" should print
Wolfgang Denk's avatar
Wolfgang Denk committed
1382 1383
		it has found a new device. The environment variable usbtty
		can be set to gserial or cdc_acm to enable your device to
Wolfgang Denk's avatar
Wolfgang Denk committed
1384
		appear to a USB host as a Linux gserial device or a
Wolfgang Denk's avatar
Wolfgang Denk committed
1385 1386 1387 1388 1389 1390 1391
		Common Device Class Abstract Control Model serial device.
		If you select usbtty = gserial you should be able to enumerate
		a Linux host by
		# modprobe usbserial vendor=0xVendorID product=0xProductID
		else if using cdc_acm, simply setting the environment
		variable usbtty to be cdc_acm should suffice. The following
		might be defined in YourBoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1392

Wolfgang Denk's avatar
Wolfgang Denk committed
1393 1394 1395 1396 1397 1398
			CONFIG_USB_DEVICE
			Define this to build a UDC device

			CONFIG_USB_TTY
			Define this to have a tty type of device available to
			talk to the UDC device
Wolfgang Denk's avatar
Wolfgang Denk committed
1399

1400 1401 1402 1403 1404 1405 1406 1407
			CONFIG_USBD_HS
			Define this to enable the high speed support for usb
			device and usbtty. If this feature is enabled, a routine
			int is_usbd_high_speed(void)
			also needs to be defined by the driver to dynamically poll
			whether the enumeration has succeded at high speed or full
			speed.

1408
			CONFIG_SYS_CONSOLE_IS_IN_ENV
Wolfgang Denk's avatar
Wolfgang Denk committed
1409 1410 1411 1412
			Define this if you want stdin, stdout &/or stderr to
			be set to usbtty.

			mpc8xx:
1413
				CONFIG_SYS_USB_EXTC_CLK 0xBLAH
Wolfgang Denk's avatar
Wolfgang Denk committed
1414
				Derive USB clock from external clock "blah"
1415
				- CONFIG_SYS_USB_EXTC_CLK 0x02
Wolfgang Denk's avatar
Wolfgang Denk committed
1416

1417
				CONFIG_SYS_USB_BRG_CLK 0xBLAH
Wolfgang Denk's avatar
Wolfgang Denk committed
1418
				Derive USB clock from brgclk
1419
				- CONFIG_SYS_USB_BRG_CLK 0x04
Wolfgang Denk's avatar
Wolfgang Denk committed
1420

Wolfgang Denk's avatar
Wolfgang Denk committed
1421
		If you have a USB-IF assigned VendorID then you may wish to
Wolfgang Denk's avatar
Wolfgang Denk committed
1422
		define your own vendor specific values either in BoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1423
		or directly in usbd_vendor_info.h. If you don't define
Wolfgang Denk's avatar
Wolfgang Denk committed
1424 1425 1426 1427 1428 1429 1430
		CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
		CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
		should pretend to be a Linux device to it's target host.

			CONFIG_USBD_MANUFACTURER
			Define this string as the name of your company for
			- CONFIG_USBD_MANUFACTURER "my company"
Wolfgang Denk's avatar
Wolfgang Denk committed
1431

Wolfgang Denk's avatar
Wolfgang Denk committed
1432 1433 1434 1435 1436 1437 1438 1439 1440
			CONFIG_USBD_PRODUCT_NAME
			Define this string as the name of your product
			- CONFIG_USBD_PRODUCT_NAME "acme usb device"

			CONFIG_USBD_VENDORID
			Define this as your assigned Vendor ID from the USB
			Implementors Forum. This *must* be a genuine Vendor ID
			to avoid polluting the USB namespace.
			- CONFIG_USBD_VENDORID 0xFFFF
Wolfgang Denk's avatar
Wolfgang Denk committed
1441

Wolfgang Denk's avatar
Wolfgang Denk committed
1442 1443 1444 1445
			CONFIG_USBD_PRODUCTID
			Define this as the unique Product ID
			for your device
			- CONFIG_USBD_PRODUCTID 0xFFFF
wdenk's avatar
wdenk committed
1446

1447 1448 1449 1450 1451 1452 1453
		Some USB device drivers may need to check USB cable attachment.
		In this case you can enable following config in BoardName.h:
			CONFIG_USB_CABLE_CHECK
			This enables function definition:
			- usb_cable_connected() in include/usb.h
			Implementation of this function is board-specific.

1454 1455 1456 1457 1458 1459 1460 1461
- ULPI Layer Support:
		The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
		the generic ULPI layer. The generic layer accesses the ULPI PHY
		via the platform viewport, so you need both the genric layer and
		the viewport enabled. Currently only Chipidea/ARC based
		viewport is supported.
		To enable the ULPI layer support, define CONFIG_USB_ULPI and
		CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
Lucas Stach's avatar
Lucas Stach committed
1462 1463 1464
		If your ULPI phy needs a different reference clock than the
		standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
		the appropriate value in Hz.
wdenk's avatar
wdenk committed
1465

1466
- MMC Support:
wdenk's avatar
wdenk committed
1467 1468 1469
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
1470
		to physical memory similar to flash. Command line is
1471 1472
		enabled with CONFIG_CMD_MMC. The MMC driver also works with
		the FAT fs. This is enabled with CONFIG_CMD_FAT.
1473

1474 1475 1476 1477 1478 1479 1480 1481 1482
		CONFIG_SH_MMCIF
		Support for Renesas on-chip MMCIF controller

			CONFIG_SH_MMCIF_ADDR
			Define the base address of MMCIF registers

			CONFIG_SH_MMCIF_CLK
			Define the clock frequency for MMCIF

1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495
- USB Device Firmware Update (DFU) class support:
		CONFIG_DFU_FUNCTION
		This enables the USB portion of the DFU USB class

		CONFIG_CMD_DFU
		This enables the command "dfu" which is used to have
		U-Boot create a DFU class device via USB.  This command
		requires that the "dfu_alt_info" environment variable be
		set and define the alt settings to expose to the host.

		CONFIG_DFU_MMC
		This enables support for exposing (e)MMC devices via DFU.

1496 1497 1498
		CONFIG_DFU_NAND
		This enables support for exposing NAND devices via DFU.

Afzal Mohammed's avatar
Afzal Mohammed committed
1499 1500 1501 1502 1503 1504
		CONFIG_DFU_RAM
		This enables support for exposing RAM via DFU.
		Note: DFU spec refer to non-volatile memory usage, but
		allow usages beyond the scope of spec - here RAM usage,
		one that would help mostly the developer.

1505 1506 1507 1508 1509 1510
		CONFIG_SYS_DFU_DATA_BUF_SIZE
		Dfu transfer uses a buffer before writing data to the
		raw storage device. Make the size (in bytes) of this buffer
		configurable. The size of this buffer is also configurable
		through the "dfu_bufsiz" environment variable.

1511 1512 1513 1514 1515 1516 1517
		CONFIG_SYS_DFU_MAX_FILE_SIZE
		When updating files rather than the raw storage device,
		we use a static buffer to copy the file into and then write
		the buffer once we've been given the whole file.  Define
		this to the maximum filesize (in bytes) for the buffer.
		Default is 4 MiB if undefined.

wdenk's avatar
wdenk committed
1518 1519 1520 1521 1522
- Journaling Flash filesystem support:
		CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
		CONFIG_JFFS2_NAND_DEV
		Define these for a default partition on a NAND device

1523 1524
		CONFIG_SYS_JFFS2_FIRST_SECTOR,
		CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
wdenk's avatar
wdenk committed
1525 1526
		Define these for a default partition on a NOR device

1527
		CONFIG_SYS_JFFS_CUSTOM_PART
wdenk's avatar
wdenk committed
1528 1529 1530 1531
		Define this to create an own partition. You have to provide a
		function struct part_info* jffs2_part_info(int part_num)

		If you define only one JFFS2 partition you may also want to
1532
		#define CONFIG_SYS_JFFS_SINGLE_PART	1
wdenk's avatar
wdenk committed
1533 1534 1535
		to disable the command chpart. This is the default when you
		have not defined a custom partition

Donggeun Kim's avatar
Donggeun Kim committed
1536 1537
- FAT(File Allocation Table) filesystem write function support:
		CONFIG_FAT_WRITE
Donggeun Kim's avatar
Donggeun Kim committed
1538 1539 1540 1541 1542 1543

		Define this to enable support for saving memory data as a
		file in FAT formatted partition.

		This will also enable the command "fatwrite" enabling the
		user to write files to FAT.
Donggeun Kim's avatar
Donggeun Kim committed
1544

1545 1546 1547 1548 1549 1550