README 108 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
wdenk's avatar
wdenk committed
2
# (C) Copyright 2000 - 2004
wdenk's avatar
wdenk committed
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
# See file CREDITS for list of people who contributed to this
# project.
#
# This program is free software; you can redistribute it and/or
# modify it under the terms of the GNU General Public License as
# published by the Free Software Foundation; either version 2 of
# the License, or (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
# MA 02111-1307 USA
#

Summary:
========

27 28 29 30
This directory contains the source code for U-Boot, a boot loader for
Embedded boards based on PowerPC and ARM processors, which can be
installed in a boot ROM and used to initialize and test the hardware
or to download and run application code.
wdenk's avatar
wdenk committed
31 32

The development of U-Boot is closely related to Linux: some parts of
33 34
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
35 36 37 38 39 40 41 42 43 44 45 46 47 48
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
49
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
50 51
"working". In fact, many of them are used in production systems.

52
In case of problems see the CHANGELOG and CREDITS files to find out
wdenk's avatar
wdenk committed
53 54 55 56 57 58
who contributed the specific port.


Where to get help:
==================

59 60 61 62
In case you have questions about, problems with or contributions for
U-Boot you should send a message to the U-Boot mailing list at
<u-boot-users@lists.sourceforge.net>. There is also an archive of
previous traffic on the mailing list - please search the archive
wdenk's avatar
wdenk committed
63 64 65 66 67 68 69 70
before asking FAQ's. Please see
http://lists.sourceforge.net/lists/listinfo/u-boot-users/


Where we come from:
===================

- start from 8xxrom sources
71
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
72 73 74 75 76 77 78 79
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
  * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
80
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
81
- add other CPU families (starting with ARM)
82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
- create U-Boot project (http://sourceforge.net/projects/u-boot)


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
105 106


wdenk's avatar
wdenk committed
107 108 109 110 111 112 113 114 115 116 117 118
Versioning:
===========

U-Boot uses a 3 level version number containing a version, a
sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
sub-version "34", and patchlevel "4".

The patchlevel is used to indicate certain stages of development
between released versions, i. e. officially released versions of
U-Boot will always have a patchlevel of "0".


wdenk's avatar
wdenk committed
119 120 121
Directory Hierarchy:
====================

wdenk's avatar
wdenk committed
122 123
- board		Board dependent files
- common	Misc architecture independent functions
wdenk's avatar
wdenk committed
124 125 126
- cpu		CPU specific files
- disk		Code for disk drive partition handling
- doc		Documentation (don't expect too much)
wdenk's avatar
wdenk committed
127
- drivers	Commonly used device drivers
wdenk's avatar
wdenk committed
128 129 130 131 132 133 134 135 136 137 138 139 140 141 142
- dtt		Digital Thermometer and Thermostat drivers
- examples	Example code for standalone applications, etc.
- include	Header Files
- disk		Harddisk interface code
- net		Networking code
- ppc		Files generic to PowerPC architecture
- post		Power On Self Test
- post/arch		Symlink to architecture specific Power On Self Test
- post/arch-ppc		PowerPC architecture specific Power On Self Test
- post/cpu/mpc8260	MPC8260 CPU specific Power On Self Test
- post/cpu/mpc8xx	MPC8xx CPU specific Power On Self Test
- rtc		Real Time Clock drivers
- tools		Tools to build S-Record or U-Boot images, etc.

- cpu/74xx_7xx	Files specific to Motorola MPC74xx and 7xx CPUs
wdenk's avatar
wdenk committed
143
- cpu/arm925t	Files specific to ARM	   925	   CPUs
144
- cpu/arm926ejs	Files specific to ARM	926	CPUs
145
- cpu/mpc5xx	Files specific to Motorola MPC5xx  CPUs
wdenk's avatar
wdenk committed
146 147 148
- cpu/mpc8xx	Files specific to Motorola MPC8xx  CPUs
- cpu/mpc824x	Files specific to Motorola MPC824x CPUs
- cpu/mpc8260	Files specific to Motorola MPC8260 CPU
149
- cpu/mpc85xx	Files specific to Motorola MPC85xx CPUs
wdenk's avatar
wdenk committed
150 151
- cpu/ppc4xx	Files specific to IBM	   4xx	   CPUs

wdenk's avatar
wdenk committed
152

wdenk's avatar
wdenk committed
153 154
- board/LEOX/   Files specific to boards manufactured by The LEOX team
- board/LEOX/elpt860	Files specific to ELPT860 boards
wdenk's avatar
wdenk committed
155 156 157
- board/RPXClassic
		Files specific to RPXClassic boards
- board/RPXlite	Files specific to RPXlite    boards
158
- board/at91rm9200dk Files specific to AT91RM9200DK boards
wdenk's avatar
wdenk committed
159
- board/c2mon	Files specific to c2mon	     boards
160
- board/cmi	Files specific to cmi        boards
wdenk's avatar
wdenk committed
161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187
- board/cogent	Files specific to Cogent     boards
		(need further configuration)
		Files specific to CPCIISER4  boards
- board/cpu86	Files specific to CPU86      boards
- board/cray/	Files specific to boards manufactured by Cray
- board/cray/L1		Files specific to L1         boards
- board/cu824	Files specific to CU824	     boards
- board/ebony   Files specific to IBM Ebony board
- board/eric	Files specific to ERIC	     boards
- board/esd/	Files specific to boards manufactured by ESD
- board/esd/adciop	Files specific to ADCIOP     boards
- board/esd/ar405	Files specific to AR405	     boards
- board/esd/canbt	Files specific to CANBT	     boards
- board/esd/cpci405	Files specific to CPCI405    boards
- board/esd/cpciiser4	Files specific to CPCIISER4  boards
- board/esd/common	Common files for ESD boards
- board/esd/dasa_sim	Files specific to DASA_SIM   boards
- board/esd/du405	Files specific to DU405      boards
- board/esd/ocrtc	Files specific to OCRTC      boards
- board/esd/pci405	Files specific to PCI405     boards
- board/esteem192e
		Files specific to ESTEEM192E boards
- board/etx094	Files specific to ETX_094    boards
- board/evb64260
		Files specific to EVB64260   boards
- board/fads	Files specific to FADS	     boards
- board/flagadm Files specific to FLAGADM    boards
wdenk's avatar
wdenk committed
188
- board/gen860t Files specific to GEN860T and GEN860T_SC    boards
wdenk's avatar
wdenk committed
189 190 191 192 193 194 195 196 197 198 199
- board/genietv Files specific to GENIETV    boards
- board/gth	Files specific to GTH	     boards
- board/hermes	Files specific to HERMES     boards
- board/hymod	Files specific to HYMOD	     boards
- board/icu862	Files specific to ICU862     boards
- board/ip860	Files specific to IP860	     boards
- board/iphase4539
		Files specific to Interphase4539 boards
- board/ivm	Files specific to IVMS8/IVML24 boards
- board/lantec	Files specific to LANTEC     boards
- board/lwmon	Files specific to LWMON	     boards
wdenk's avatar
wdenk committed
200 201 202
- board/Marvell Files specific to Marvell development boards
- board/Marvell/db64360 Files specific to db64360 board
- board/Marvell/db64460 Files specific to db64460 board
wdenk's avatar
wdenk committed
203 204
- board/mbx8xx	Files specific to MBX	     boards
- board/mpc8260ads
205
		Files specific to MPC826xADS and PQ2FADS-ZU/VR boards
206 207 208 209
- board/mpc8540ads
		Files specific to MPC8540ADS boards
- board/mpc8560ads
		Files specific to MPC8560ADS boards
wdenk's avatar
wdenk committed
210 211 212 213
- board/mpl/	Files specific to boards manufactured by MPL
- board/mpl/common	Common files for MPL boards
- board/mpl/pip405	Files specific to PIP405     boards
- board/mpl/mip405	Files specific to MIP405     boards
wdenk's avatar
wdenk committed
214
- board/mpl/vcma9	Files specific to VCMA9      boards
wdenk's avatar
wdenk committed
215 216 217 218
- board/musenki	Files specific to MUSEKNI    boards
- board/mvs1	Files specific to MVS1       boards
- board/nx823   Files specific to NX823      boards
- board/oxc	Files specific to OXC        boards
219
- board/omap1510inn
wdenk's avatar
wdenk committed
220
		Files specific to OMAP 1510 Innovator boards
221
- board/omap1610inn
222
		Files specific to OMAP 1610 Innovator boards
wdenk's avatar
wdenk committed
223 224 225 226
- board/pcippc2	Files specific to PCIPPC2/PCIPPC6 boards
- board/pm826	Files specific to PM826      boards
- board/ppmc8260
		Files specific to PPMC8260   boards
wdenk's avatar
wdenk committed
227 228
- board/snmc/qs850	Files specific to QS850/823  boards
- board/snmc/qs860t	Files specific to QS860T     boards
wdenk's avatar
wdenk committed
229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251
- board/rpxsuper
		Files specific to RPXsuper   boards
- board/rsdproto
		Files specific to RSDproto   boards
- board/sandpoint
		Files specific to Sandpoint  boards
- board/sbc8260	Files specific to SBC8260    boards
- board/sacsng	Files specific to SACSng     boards
- board/siemens Files specific to boards manufactured by Siemens AG
- board/siemens/CCM	Files specific to CCM	     boards
- board/siemens/IAD210	Files specific to IAD210     boards
- board/siemens/SCM	Files specific to SCM        boards
- board/siemens/pcu_e	Files specific to PCU_E	     boards
- board/sixnet	Files specific to SIXNET     boards
- board/spd8xx	Files specific to SPD8xxTS   boards
- board/tqm8260 Files specific to TQM8260    boards
- board/tqm8xx	Files specific to TQM8xxL    boards
- board/w7o	Files specific to W7O        boards
- board/walnut405
		Files specific to Walnut405  boards
- board/westel/	Files specific to boards manufactured by Westel Wireless
- board/westel/amx860	Files specific to AMX860     boards
- board/utx8245	Files specific to UTX8245   boards
wdenk's avatar
wdenk committed
252
- board/zpc1900	Files specific to Zephyr Engineering ZPC.1900 board
wdenk's avatar
wdenk committed
253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
  "CFG_".

Later we will add a configuration tool - probably similar to or even
identical to what's used for the Linux kernel. Right now, we have to
do the configuration by hand, which means creating some symbolic
links and editing some configuration files. We use the TQM8xxL boards
as an example here.


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
configurations available; just type "make <board_name>_config".

Example: For a TQM823L module type:

	cd u-boot
	make TQM823L_config

For the Cogent platform, you need to specify the cpu type as well;
e.g. "make cogent_mpc8xx_config". And also configure the cogent
directory according to the instructions in cogent/README.


Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
305 306 307 308 309
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.


wdenk's avatar
wdenk committed
310 311 312 313 314 315 316
The following options need to be configured:

- CPU Type:	Define exactly one of

		PowerPC based CPUs:
		-------------------
		CONFIG_MPC823,	CONFIG_MPC850,	CONFIG_MPC855,	CONFIG_MPC860
317
	or	CONFIG_MPC5xx
wdenk's avatar
wdenk committed
318
	or	CONFIG_MPC824X, CONFIG_MPC8260
319
	or	CONFIG_MPC85xx
wdenk's avatar
wdenk committed
320 321
	or	CONFIG_IOP480
	or	CONFIG_405GP
322
	or	CONFIG_405EP
wdenk's avatar
wdenk committed
323 324
	or	CONFIG_440
	or	CONFIG_MPC74xx
wdenk's avatar
wdenk committed
325
	or	CONFIG_750FX
wdenk's avatar
wdenk committed
326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367

		ARM based CPUs:
		---------------
		CONFIG_SA1110
		CONFIG_ARM7
		CONFIG_PXA250


- Board Type:	Define exactly one of

		PowerPC based boards:
		---------------------

		CONFIG_ADCIOP,     CONFIG_ICU862      CONFIG_RPXsuper,
		CONFIG_ADS860,     CONFIG_IP860,      CONFIG_SM850,
		CONFIG_AMX860,     CONFIG_IPHASE4539, CONFIG_SPD823TS,
		CONFIG_AR405,      CONFIG_IVML24,     CONFIG_SXNI855T,
		CONFIG_BAB7xx,     CONFIG_IVML24_128, CONFIG_Sandpoint8240,
		CONFIG_CANBT,      CONFIG_IVML24_256, CONFIG_Sandpoint8245,
		CONFIG_CCM,        CONFIG_IVMS8,      CONFIG_TQM823L,
		CONFIG_CPCI405,    CONFIG_IVMS8_128,  CONFIG_TQM850L,
		CONFIG_CPCI4052,   CONFIG_IVMS8_256,  CONFIG_TQM855L,
		CONFIG_CPCIISER4,  CONFIG_LANTEC,     CONFIG_TQM860L,
		CONFIG_CPU86,      CONFIG_MBX,        CONFIG_TQM8260,
		CONFIG_CRAYL1,     CONFIG_MBX860T,    CONFIG_TTTech,
		CONFIG_CU824,      CONFIG_MHPC,       CONFIG_UTX8245,
		CONFIG_DASA_SIM,   CONFIG_MIP405,     CONFIG_W7OLMC,
		CONFIG_DU405,      CONFIG_MOUSSE,     CONFIG_W7OLMG,
		CONFIG_ELPPC,      CONFIG_MPC8260ADS, CONFIG_WALNUT405,
		CONFIG_ERIC,       CONFIG_MUSENKI,    CONFIG_ZUMA,
		CONFIG_ESTEEM192E, CONFIG_MVS1,       CONFIG_c2mon,
		CONFIG_ETX094,     CONFIG_NX823,      CONFIG_cogent_mpc8260,
		CONFIG_EVB64260,   CONFIG_OCRTC,      CONFIG_cogent_mpc8xx,
		CONFIG_FADS823,    CONFIG_ORSG,       CONFIG_ep8260,
		CONFIG_FADS850SAR, CONFIG_OXC,        CONFIG_gw8260,
		CONFIG_FADS860T,   CONFIG_PCI405,     CONFIG_hermes,
		CONFIG_FLAGADM,    CONFIG_PCIPPC2,    CONFIG_hymod,
		CONFIG_FPS850L,    CONFIG_PCIPPC6,    CONFIG_lwmon,
		CONFIG_GEN860T,    CONFIG_PIP405,     CONFIG_pcu_e,
		CONFIG_GENIETV,    CONFIG_PM826,      CONFIG_ppmc8260,
		CONFIG_GTH,        CONFIG_RPXClassic, CONFIG_rsdproto,
		CONFIG_IAD210,     CONFIG_RPXlite,    CONFIG_sbc8260,
wdenk's avatar
wdenk committed
368
		CONFIG_EBONY,      CONFIG_sacsng,     CONFIG_FPS860L,
369
		CONFIG_V37,        CONFIG_ELPT860,    CONFIG_CMI,
370
		CONFIG_NETVIA,     CONFIG_RBC823,     CONFIG_ZPC1900,
wdenk's avatar
wdenk committed
371 372
		CONFIG_MPC8540ADS, CONFIG_MPC8560ADS, CONFIG_QS850,
		CONFIG_QS823,      CONFIG_QS860T,     CONFIG_DB64360,
373
		CONFIG_DB64460,	   CONFIG_DUET_ADS
wdenk's avatar
wdenk committed
374 375 376 377 378 379

		ARM based boards:
		-----------------

		CONFIG_HHP_CRADLE,  CONFIG_DNP1110,    CONFIG_EP7312,
		CONFIG_IMPA7,       CONFIG_LART,       CONFIG_LUBBOCK,
380
		CONFIG_INNOVATOROMAP1510,	CONFIG_INNOVATOROMAP1610
wdenk's avatar
wdenk committed
381
		CONFIG_SHANNON,     CONFIG_SMDK2400,   CONFIG_SMDK2410,
wdenk's avatar
wdenk committed
382
		CONFIG_TRAB,	    CONFIG_VCMA9,      CONFIG_AT91RM9200DK
wdenk's avatar
wdenk committed
383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405


- CPU Module Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA286_60_OLD
--- FIXME --- not tested yet:
		CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
		CONFIG_CMA287_23, CONFIG_CMA287_50

- Motherboard Type: (if CONFIG_COGENT is defined)
		Define exactly one of
		CONFIG_CMA101, CONFIG_CMA102

- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
		Define one or more of
		CONFIG_CMA302

- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
		Define one or more of
		CONFIG_LCD_HEARTBEAT	- update a character position on
					  the lcd display every second with
					  a "rotator" |\-/|\-/

wdenk's avatar
wdenk committed
406 407 408 409
- Board flavour: (if CONFIG_MPC8260ADS is defined)
		CONFIG_ADSTYPE
		Possible values are:
			CFG_8260ADS	- original MPC8260ADS
410
			CFG_8266ADS	- MPC8266ADS
wdenk's avatar
wdenk committed
411
			CFG_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
wdenk's avatar
wdenk committed
412 413


wdenk's avatar
wdenk committed
414
- MPC824X Family Member (if CONFIG_MPC824X is defined)
wdenk's avatar
wdenk committed
415 416
		Define exactly one of
		CONFIG_MPC8240, CONFIG_MPC8245
wdenk's avatar
wdenk committed
417 418 419

- 8xx CPU Options: (if using an 8xx cpu)
		Define one or more of
wdenk's avatar
wdenk committed
420 421 422
		CONFIG_8xx_GCLK_FREQ	- if get_gclk_freq() cannot work
					  e.g. if there is no 32KHz
					  reference PIT/RTC clock
wdenk's avatar
wdenk committed
423

wdenk's avatar
wdenk committed
424
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
425 426 427 428 429 430 431 432 433 434 435 436 437
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
		"clocks_in_mhz=1" is  automatically  included  in  the
		default environment.

wdenk's avatar
wdenk committed
438 439 440 441 442 443
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

		When transfering memsize parameter to linux, some versions
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

wdenk's avatar
wdenk committed
444
- Console Interface:
445 446 447 448
		Depending on board, define exactly one serial port
		(like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
		CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
		console by defining CONFIG_8xx_CONS_NONE
wdenk's avatar
wdenk committed
449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485

		Note: if CONFIG_8xx_CONS_NONE is defined, the serial
		port routines must be defined elsewhere
		(i.e. serial_init(), serial_getc(), ...)

		CONFIG_CFB_CONSOLE
		Enables console device for a color framebuffer. Needs following
		defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
			VIDEO_FB_LITTLE_ENDIAN	graphic memory organisation
						(default big endian)
			VIDEO_HW_RECTFILL	graphic chip supports
						rectangle fill
						(cf. smiLynxEM)
			VIDEO_HW_BITBLT		graphic chip supports
						bit-blit (cf. smiLynxEM)
			VIDEO_VISIBLE_COLS	visible pixel columns
						(cols=pitch)
			VIDEO_VISIBLE_ROWS      visible pixel rows
			VIDEO_PIXEL_SIZE        bytes per pixel
			VIDEO_DATA_FORMAT	graphic data format
						(0-5, cf. cfb_console.c)
			VIDEO_FB_ADRS           framebuffer address
			VIDEO_KBD_INIT_FCT	keyboard int fct
						(i.e. i8042_kbd_init())
			VIDEO_TSTC_FCT		test char fct
						(i.e. i8042_tstc)
			VIDEO_GETC_FCT		get char fct
						(i.e. i8042_getc)
			CONFIG_CONSOLE_CURSOR	cursor drawing on/off
						(requires blink timer
						cf. i8042.c)
			CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
			CONFIG_CONSOLE_TIME	display time/date info in
						upper right corner
						(requires CFG_CMD_DATE)
			CONFIG_VIDEO_LOGO	display Linux logo in
						upper left corner
486 487 488
			CONFIG_VIDEO_BMP_LOGO	use bmp_logo.h instead of
						linux_logo.h for logo.
						Requires CONFIG_VIDEO_LOGO
wdenk's avatar
wdenk committed
489 490 491 492
			CONFIG_CONSOLE_EXTRA_INFO
						addional board info beside
						the logo

493 494 495
		When CONFIG_CFB_CONSOLE is defined, video console is
		default i/o. Serial console can be forced with
		environment 'console=serial'.
wdenk's avatar
wdenk committed
496

wdenk's avatar
wdenk committed
497 498 499 500
		When CONFIG_SILENT_CONSOLE is defined, all console
		messages (by U-Boot and Linux!) can be silenced with
		the "silent" environment variable. See
		doc/README.silent for more information.
wdenk's avatar
wdenk committed
501

wdenk's avatar
wdenk committed
502 503 504 505
- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
		CFG_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
506
		CFG_BRGCLK_PRESCALE, baudrate prescale
wdenk's avatar
wdenk committed
507 508 509 510 511 512 513 514 515 516 517 518 519

- Interrupt driven serial port input:
		CONFIG_SERIAL_SOFTWARE_FIFO

		PPC405GP only.
		Use an interrupt handler for receiving data on the
		serial port. It also enables using hardware handshake
		(RTS/CTS) and UART's built-in FIFO. Set the number of
		bytes the interrupt driven input buffer should have.

		Set to 0 to disable this feature (this is the default).
		This will also disable hardware handshake.

stroese's avatar
stroese committed
520 521 522 523 524 525 526
- Console UART Number:
		CONFIG_UART1_CONSOLE

		IBM PPC4xx only.
		If defined internal UART1 (and not UART0) is used
		as default U-Boot console.

wdenk's avatar
wdenk committed
527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551
- Boot Delay:	CONFIG_BOOTDELAY - in seconds
		Delay before automatically booting the default image;
		set to -1 to disable autoboot.

		See doc/README.autoboot for these options that
		work with CONFIG_BOOTDELAY. None are required.
		CONFIG_BOOT_RETRY_TIME
		CONFIG_BOOT_RETRY_MIN
		CONFIG_AUTOBOOT_KEYED
		CONFIG_AUTOBOOT_PROMPT
		CONFIG_AUTOBOOT_DELAY_STR
		CONFIG_AUTOBOOT_STOP_STR
		CONFIG_AUTOBOOT_DELAY_STR2
		CONFIG_AUTOBOOT_STOP_STR2
		CONFIG_ZERO_BOOTDELAY_CHECK
		CONFIG_RESET_TO_RETRY

- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_BOOTARGS
552 553 554
		This can be used to pass arguments to the bootm
		command. The value of CONFIG_BOOTARGS goes into the
		environment value "bootargs".
wdenk's avatar
wdenk committed
555 556

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
557 558 559 560
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
		ram and nfs.
wdenk's avatar
wdenk committed
561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602

- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
		CFG_BAUDRATE_TABLE, see below.

- Monitor Functions:
		CONFIG_COMMANDS
		Most monitor functions can be selected (or
		de-selected) by adjusting the definition of
		CONFIG_COMMANDS; to select individual functions,
		#define CONFIG_COMMANDS by "OR"ing any of the
		following values:

		#define enables commands:
		-------------------------
		CFG_CMD_ASKENV	* ask for env variable
wdenk's avatar
wdenk committed
603
		CFG_CMD_AUTOSCRIPT Autoscript Support
wdenk's avatar
wdenk committed
604 605
		CFG_CMD_BDI	  bdinfo
		CFG_CMD_BEDBUG	  Include BedBug Debugger
wdenk's avatar
wdenk committed
606
		CFG_CMD_BMP     * BMP support
wdenk's avatar
wdenk committed
607 608 609 610 611
		CFG_CMD_BOOTD	  bootd
		CFG_CMD_CACHE	  icache, dcache
		CFG_CMD_CONSOLE	  coninfo
		CFG_CMD_DATE	* support for RTC, date/time...
		CFG_CMD_DHCP	  DHCP support
wdenk's avatar
wdenk committed
612 613
		CFG_CMD_DIAG    * Diagnostics
		CFG_CMD_DOC     * Disk-On-Chip Support
614
		CFG_CMD_DTT       Digital Therm and Thermostat
wdenk's avatar
wdenk committed
615 616 617 618 619
		CFG_CMD_ECHO	* echo arguments
		CFG_CMD_EEPROM	* EEPROM read/write support
		CFG_CMD_ELF	  bootelf, bootvx
		CFG_CMD_ENV	  saveenv
		CFG_CMD_FDC	* Floppy Disk Support
620
		CFG_CMD_FAT	  FAT partition support
621
		CFG_CMD_FDOS	* Dos diskette Support
wdenk's avatar
wdenk committed
622 623
		CFG_CMD_FLASH	  flinfo, erase, protect
		CFG_CMD_FPGA	  FPGA device initialization support
wdenk's avatar
wdenk committed
624
		CFG_CMD_HWFLOW  * RTS/CTS hw flow control
wdenk's avatar
wdenk committed
625 626 627
		CFG_CMD_I2C	* I2C serial bus support
		CFG_CMD_IDE	* IDE harddisk support
		CFG_CMD_IMI	  iminfo
wdenk's avatar
wdenk committed
628
		CFG_CMD_IMLS      List all found images
wdenk's avatar
wdenk committed
629 630
		CFG_CMD_IMMAP	* IMMR dump support
		CFG_CMD_IRQ	* irqinfo
wdenk's avatar
wdenk committed
631
		CFG_CMD_JFFS2   * JFFS2 Support
wdenk's avatar
wdenk committed
632 633 634 635 636
		CFG_CMD_KGDB	* kgdb
		CFG_CMD_LOADB	  loadb
		CFG_CMD_LOADS	  loads
		CFG_CMD_MEMORY	  md, mm, nm, mw, cp, cmp, crc, base,
				  loop, mtest
wdenk's avatar
wdenk committed
637
		CFG_CMD_MISC      Misc functions like sleep etc
638
		CFG_CMD_MMC	  MMC memory mapped support
wdenk's avatar
wdenk committed
639
		CFG_CMD_MII	  MII utility commands
wdenk's avatar
wdenk committed
640
		CFG_CMD_NAND    * NAND support
wdenk's avatar
wdenk committed
641 642 643
		CFG_CMD_NET	  bootp, tftpboot, rarpboot
		CFG_CMD_PCI	* pciinfo
		CFG_CMD_PCMCIA	* PCMCIA support
wdenk's avatar
wdenk committed
644
		CFG_CMD_PING    * send ICMP ECHO_REQUEST to network host
645
		CFG_CMD_PORTIO  * Port I/O
wdenk's avatar
wdenk committed
646 647
		CFG_CMD_REGINFO * Register dump
		CFG_CMD_RUN	  run command in env variable
wdenk's avatar
wdenk committed
648
		CFG_CMD_SAVES     save S record dump
wdenk's avatar
wdenk committed
649
		CFG_CMD_SCSI	* SCSI Support
wdenk's avatar
wdenk committed
650
		CFG_CMD_SDRAM   * print SDRAM configuration information
wdenk's avatar
wdenk committed
651 652 653
		CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
		CFG_CMD_SPI	* SPI serial bus support
		CFG_CMD_USB	* USB support
wdenk's avatar
wdenk committed
654
		CFG_CMD_VFD     * VFD support (TRAB)
wdenk's avatar
wdenk committed
655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675
		CFG_CMD_BSP	* Board SPecific functions
		-----------------------------------------------
		CFG_CMD_ALL	all

		CFG_CMD_DFL	Default configuration; at the moment
				this is includes all commands, except
				the ones marked with "*" in the list
				above.

		If you don't define CONFIG_COMMANDS it defaults to
		CFG_CMD_DFL in include/cmd_confdefs.h. A board can
		override the default settings in the respective
		include file.

		EXAMPLE: If you want all functions except of network
		support you can write:

		#define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)


	Note:	Don't enable the "icache" and "dcache" commands
676 677 678 679 680 681 682
		(configuration option CFG_CMD_CACHE) unless you know
		what you (and your U-Boot users) are doing. Data
		cache cannot be enabled on systems like the 8xx or
		8260 (where accesses to the IMMR region must be
		uncached), and it cannot be disabled on all other
		systems where we (mis-) use the data cache to hold an
		initial stack and some data.
wdenk's avatar
wdenk committed
683 684 685 686 687 688 689


		XXX - this list needs to get updated!

- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
wdenk's avatar
wdenk committed
690
		support. There must be support in the platform specific
wdenk's avatar
wdenk committed
691 692 693 694
		code for a watchdog. For the 8xx and 8260 CPUs, the
		SIU Watchdog feature is enabled in the SYPCR
		register.

695 696 697 698 699 700 701
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
		This variable is readonly.

wdenk's avatar
wdenk committed
702 703 704 705 706 707 708 709 710
- Real-Time Clock:

		When CFG_CMD_DATE is selected, the type of the RTC
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_MPC8xx	- use internal RTC of MPC8xx
		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
		CONFIG_RTC_MC146818	- use MC146818 RTC
wdenk's avatar
wdenk committed
711
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
712
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
713
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
wdenk's avatar
wdenk committed
714
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
wdenk's avatar
wdenk committed
715

wdenk's avatar
wdenk committed
716 717 718
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

wdenk's avatar
wdenk committed
719 720
- Timestamp Support:

721 722 723 724
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
		automatically enabled when you select CFG_CMD_DATE .
wdenk's avatar
wdenk committed
725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757

- Partition Support:
		CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
		and/or CONFIG_ISO_PARTITION

		If IDE or SCSI support	is  enabled  (CFG_CMD_IDE  or
		CFG_CMD_SCSI) you must configure support for at least
		one partition type as well.

- IDE Reset method:
		CONFIG_IDE_RESET_ROUTINE

		Set this to define that instead of a reset Pin, the
		routine ide_set_reset(int idereset) will be used.

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

- SCSI Support:
		At the moment only there is only support for the
		SYM53C8XX SCSI controller; define
		CONFIG_SCSI_SYM53C8XX to enable it.

		CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
		CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
		CFG_SCSI_MAX_LUN] can be adjusted to define the
		maximum numbers of LUNs, SCSI ID's and target
		devices.
		CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)

- NETWORK Support (PCI):
758 759
		CONFIG_E1000
		Support for Intel 8254x gigabit chips.
stroese's avatar
stroese committed
760

wdenk's avatar
wdenk committed
761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
		Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

wdenk's avatar
wdenk committed
777 778 779 780 781 782 783 784 785 786 787 788
- NETWORK Support (other):

		CONFIG_DRIVER_LAN91C96
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_BASE
			Define this to hold the physical address
			of the LAN91C96's I/O space

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

wdenk's avatar
wdenk committed
789 790 791 792 793 794 795 796 797 798 799
- USB Support:
		At the moment only the UHCI host controller is
		supported (PIP405, MIP405); define
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
		end define CONFIG_USB_STORAGE to enable the USB
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).

800
- MMC Support:
wdenk's avatar
wdenk committed
801 802 803
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
804 805
		to physical memory similar to flash. Command line is
		enabled with CFG_CMD_MMC. The MMC driver also works with
wdenk's avatar
wdenk committed
806
		the FAT fs. This is enabled with CFG_CMD_FAT.
807

wdenk's avatar
wdenk committed
808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835
- Keyboard Support:
		CONFIG_ISA_KEYBOARD

		Define this to enable standard (PC-Style) keyboard
		support

		CONFIG_I8042_KBD
		Standard PC keyboard driver with US (is default) and
		GERMAN key layout (switch via environment 'keymap=de') support.
		Export function i8042_kbd_init, i8042_tstc and i8042_getc
		for cfb_console. Supports cursor blinking.

- Video support:
		CONFIG_VIDEO

		Define this to enable video support (for output to
		video).

		CONFIG_VIDEO_CT69000

		Enable Chips & Technologies 69000 Video chip

		CONFIG_VIDEO_SMI_LYNXEM
		Enable Silicon Motion SMI 712/710/810 Video chip
		Videomode are selected via environment 'videomode' with
		standard LiLo mode numbers.
		Following modes are supported  (* is default):

836 837 838 839
			    800x600  1024x768  1280x1024
	      256  (8bit)     303*      305       307
	    65536 (16bit)     314       317       31a
	16,7 Mill (24bit)     315       318       31b
wdenk's avatar
wdenk committed
840 841
		(i.e. setenv videomode 317; saveenv; reset;)

842
		CONFIG_VIDEO_SED13806
843
		Enable Epson SED13806 driver. This driver supports 8bpp
844 845 846
		and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
		or CONFIG_VIDEO_SED13806_16BPP

847
- Keyboard Support:
wdenk's avatar
wdenk committed
848
		CONFIG_KEYBOARD
849

wdenk's avatar
wdenk committed
850 851 852 853
		Define this to enable a custom keyboard support.
		This simply calls drv_keyboard_init() which must be
		defined in your board-specific files.
		The only board using this so far is RBC823.
854

wdenk's avatar
wdenk committed
855 856 857 858 859 860
- LCD Support:	CONFIG_LCD

		Define this to enable LCD support (for output to LCD
		display); also select one of the supported displays
		by defining one of these:

wdenk's avatar
wdenk committed
861
		CONFIG_NEC_NL6448AC33:
wdenk's avatar
wdenk committed
862

wdenk's avatar
wdenk committed
863
			NEC NL6448AC33-18. Active, color, single scan.
wdenk's avatar
wdenk committed
864

wdenk's avatar
wdenk committed
865
		CONFIG_NEC_NL6448BC20
wdenk's avatar
wdenk committed
866

wdenk's avatar
wdenk committed
867 868 869 870 871 872
			NEC NL6448BC20-08. 6.5", 640x480.
			Active, color, single scan.

		CONFIG_NEC_NL6448BC33_54

			NEC NL6448BC33-54. 10.4", 640x480.
wdenk's avatar
wdenk committed
873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902
			Active, color, single scan.

		CONFIG_SHARP_16x9

			Sharp 320x240. Active, color, single scan.
			It isn't 16x9, and I am not sure what it is.

		CONFIG_SHARP_LQ64D341

			Sharp LQ64D341 display, 640x480.
			Active, color, single scan.

		CONFIG_HLD1045

			HLD1045 display, 640x480.
			Active, color, single scan.

		CONFIG_OPTREX_BW

			Optrex	 CBL50840-2 NF-FW 99 22 M5
			or
			Hitachi	 LMG6912RPFC-00T
			or
			Hitachi	 SP14Q002

			320x240. Black & white.

		Normally display is black on white background; define
		CFG_WHITE_ON_BLACK to get it inverted.

wdenk's avatar
wdenk committed
903
- Splash Screen Support: CONFIG_SPLASH_SCREEN
904

wdenk's avatar
wdenk committed
905 906 907 908 909 910 911 912
		If this option is set, the environment is checked for
		a variable "splashimage". If found, the usual display
		of logo, copyright and system information on the LCD
		is supressed and the BMP image at the address
		specified in "splashimage" is loaded instead. The
		console is redirected to the "nulldev", too. This
		allows for a "silent" boot where a splash screen is
		loaded very quickly after power-on.
913

wdenk's avatar
wdenk committed
914 915 916 917 918 919 920
- Compression support:
		CONFIG_BZIP2

		If this option is set, support for bzip2 compressed
		images is included. If not, only uncompressed and gzip
		compressed images are supported.

921 922 923
		NOTE: the bzip2 algorithm requires a lot of RAM, so
		the malloc area (as defined by CFG_MALLOC_LEN) should
		be at least 4MB.
924

wdenk's avatar
wdenk committed
925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965
- Ethernet address:
		CONFIG_ETHADDR
		CONFIG_ETH2ADDR
		CONFIG_ETH3ADDR

		Define a default value for ethernet address to use
		for the respective ethernet interface, in case this
		is not determined automatically.

- IP address:
		CONFIG_IPADDR

		Define a default value for the IP address to use for
		the default ethernet interface, in case this is not
		determined through e.g. bootp.

- Server IP address:
		CONFIG_SERVERIP

		Defines a default value for theIP address of a TFTP
		server to contact when using the "tftboot" command.

- BOOTP Recovery Mode:
		CONFIG_BOOTP_RANDOM_DELAY

		If you have many targets in a network that try to
		boot using BOOTP, you may want to avoid that all
		systems send out BOOTP requests at precisely the same
		moment (which would happen for instance at recovery
		from a power failure, when all systems will try to
		boot, thus flooding the BOOTP server. Defining
		CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
		inserted before sending out BOOTP requests. The
		following delays are insterted then:

		1st BOOTP request:	delay 0 ... 1 sec
		2nd BOOTP request:	delay 0 ... 2 sec
		3rd BOOTP request:	delay 0 ... 4 sec
		4th and following
		BOOTP requests:		delay 0 ... 8 sec

966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988
- DHCP Advanced Options:
		CONFIG_BOOTP_MASK

		You can fine tune the DHCP functionality by adding
		these flags to the CONFIG_BOOTP_MASK define:

		CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
		serverip from a DHCP server, it is possible that more
		than one DNS serverip is offered to the client.
		If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
		serverip will be stored in the additional environment
		variable "dnsip2". The first DNS serverip is always
		stored in the variable "dnsip", when CONFIG_BOOTP_DNS
		is added to the CONFIG_BOOTP_MASK.

		CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
		to do a dynamic update of a DNS server. To do this, they
		need the hostname of the DHCP requester.
		If CONFIG_BOOP_SEND_HOSTNAME is added to the
		CONFIG_BOOTP_MASK, the content of the "hostname"
		environment variable is passed as option 12 to
		the DHCP server.

wdenk's avatar
wdenk committed
989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007
- Status LED:	CONFIG_STATUS_LED

		Several configurations allow to display the current
		status using a LED. For instance, the LED will blink
		fast while running U-Boot code, stop blinking as
		soon as a reply to a BOOTP request was received, and
		start blinking slow once the Linux kernel is running
		(supported by a status LED driver in the Linux
		kernel). Defining CONFIG_STATUS_LED enables this
		feature in U-Boot.

- CAN Support:	CONFIG_CAN_DRIVER

		Defining CONFIG_CAN_DRIVER enables CAN driver support
		on those systems that support this (optional)
		feature, like the TQM8xxL modules.

- I2C Support:	CONFIG_HARD_I2C | CONFIG_SOFT_I2C

wdenk's avatar
wdenk committed
1008
		These enable I2C serial bus commands. Defining either of
1009 1010
		(but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
		include the appropriate I2C driver for the selected cpu.
wdenk's avatar
wdenk committed
1011

1012 1013
		This will allow you to use i2c commands at the u-boot
		command line (as long as you set CFG_CMD_I2C in
wdenk's avatar
wdenk committed
1014 1015
		CONFIG_COMMANDS) and communicate with i2c based realtime
		clock chips. See common/cmd_i2c.c for a description of the
1016
		command line interface.
wdenk's avatar
wdenk committed
1017

1018
		CONFIG_HARD_I2C	selects the CPM hardware driver for I2C.
wdenk's avatar
wdenk committed
1019

1020
		CONFIG_SOFT_I2C configures u-boot to use a software (aka
wdenk's avatar
wdenk committed
1021 1022
		bit-banging) driver instead of CPM or similar hardware
		support for I2C.
wdenk's avatar
wdenk committed
1023

1024
		There are several other quantities that must also be
wdenk's avatar
wdenk committed
1025
		defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
wdenk's avatar
wdenk committed
1026

wdenk's avatar
wdenk committed
1027
		In both cases you will need to define CFG_I2C_SPEED
1028 1029 1030 1031
		to be the frequency (in Hz) at which you wish your i2c bus
		to run and CFG_I2C_SLAVE to be the address of this node (ie
		the cpu's i2c node address).

wdenk's avatar
wdenk committed
1032 1033 1034
		Now, the u-boot i2c code for the mpc8xx (cpu/mpc8xx/i2c.c)
		sets the cpu up as a master node and so its address should
		therefore be cleared to 0 (See, eg, MPC823e User's Manual
1035
		p.16-473). So, set CFG_I2C_SLAVE to 0.
wdenk's avatar
wdenk committed
1036

1037
		That's all that's required for CONFIG_HARD_I2C.
wdenk's avatar
wdenk committed
1038

wdenk's avatar
wdenk committed
1039 1040 1041
		If you use the software i2c interface (CONFIG_SOFT_I2C)
		then the following macros need to be defined (examples are
		from include/configs/lwmon.h):
wdenk's avatar
wdenk committed
1042 1043 1044

		I2C_INIT

wdenk's avatar
wdenk committed
1045
		(Optional). Any commands necessary to enable the I2C
1046
		controller or configure ports.
wdenk's avatar
wdenk committed
1047

wdenk's avatar
wdenk committed
1048 1049
		eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |=  PB_SCL)

wdenk's avatar
wdenk committed
1050 1051
		I2C_PORT

1052 1053 1054
		(Only for MPC8260 CPU). The I/O port to use (the code
		assumes both bits are on the same port). Valid values
		are 0..3 for ports A..D.
wdenk's avatar
wdenk committed
1055 1056 1057 1058 1059 1060 1061

		I2C_ACTIVE

		The code necessary to make the I2C data line active
		(driven).  If the data line is open collector, this
		define can be null.

wdenk's avatar
wdenk committed
1062 1063
		eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |=  PB_SDA)

wdenk's avatar
wdenk committed
1064 1065 1066 1067 1068 1069
		I2C_TRISTATE

		The code necessary to make the I2C data line tri-stated
		(inactive).  If the data line is open collector, this
		define can be null.

wdenk's avatar
wdenk committed
1070 1071
		eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)

wdenk's avatar
wdenk committed
1072 1073 1074 1075 1076
		I2C_READ

		Code that returns TRUE if the I2C data line is high,
		FALSE if it is low.

wdenk's avatar
wdenk committed
1077 1078
		eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)

wdenk's avatar
wdenk committed
1079 1080 1081 1082 1083
		I2C_SDA(bit)

		If <bit> is TRUE, sets the I2C data line high. If it
		is FALSE, it clears it (low).

wdenk's avatar
wdenk committed
1084
		eg: #define I2C_SDA(bit) \
wdenk's avatar
wdenk committed
1085 1086
			if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
wdenk's avatar
wdenk committed
1087

wdenk's avatar
wdenk committed
1088 1089 1090 1091 1092
		I2C_SCL(bit)

		If <bit> is TRUE, sets the I2C clock line high. If it
		is FALSE, it clears it (low).

wdenk's avatar
wdenk committed
1093
		eg: #define I2C_SCL(bit) \
wdenk's avatar
wdenk committed
1094 1095
			if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
wdenk's avatar
wdenk committed
1096

wdenk's avatar
wdenk committed
1097 1098 1099 1100
		I2C_DELAY

		This delay is invoked four times per clock cycle so this
		controls the rate of data transfer.  The data rate thus
wdenk's avatar
wdenk committed
1101
		is 1 / (I2C_DELAY * 4). Often defined to be something
1102 1103
		like:

wdenk's avatar
wdenk committed
1104
		#define I2C_DELAY  udelay(2)
wdenk's avatar
wdenk committed
1105

1106 1107
		CFG_I2C_INIT_BOARD

wdenk's avatar
wdenk committed
1108 1109 1110 1111 1112 1113 1114 1115
		When a board is reset during an i2c bus transfer
		chips might think that the current transfer is still
		in progress. On some boards it is possible to access
		the i2c SCLK line directly, either by using the
		processor pin as a GPIO or by having a second pin
		connected to the bus. If this option is defined a
		custom i2c_init_board() routine in boards/xxx/board.c
		is run early in the boot sequence.
1116

wdenk's avatar
wdenk committed
1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129
- SPI Support:	CONFIG_SPI

		Enables SPI driver (so far only tested with
		SPI EEPROM, also an instance works with Crystal A/D and
		D/As on the SACSng board)

		CONFIG_SPI_X

		Enables extended (16-bit) SPI EEPROM addressing.
		(symmetrical to CONFIG_I2C_X)

		CONFIG_SOFT_SPI

1130 1131 1132 1133 1134 1135 1136
		Enables a software (bit-bang) SPI driver rather than
		using hardware support. This is a general purpose
		driver that only requires three general I/O port pins
		(two outputs, one input) to function. If this is
		defined, the board configuration must define several
		SPI configuration items (port pins to use, etc). For
		an example, see include/configs/sacsng.h.
wdenk's avatar
wdenk committed
1137 1138 1139

- FPGA Support: CONFIG_FPGA_COUNT

1140
		Specify the number of FPGA devices to support.
wdenk's avatar
wdenk committed
1141

1142
		CONFIG_FPGA
wdenk's avatar
wdenk committed
1143

1144
		Used to specify the types of FPGA devices. For
wdenk's avatar
wdenk committed
1145
		example,
wdenk's avatar
wdenk committed
1146
		#define CONFIG_FPGA  CFG_XILINX_VIRTEX2
wdenk's avatar
wdenk committed
1147

wdenk's avatar
wdenk committed
1148
		CFG_FPGA_PROG_FEEDBACK
wdenk's avatar
wdenk committed
1149

1150
		Enable printing of hash marks during FPGA
wdenk's avatar
wdenk committed
1151 1152 1153 1154
		configuration.

		CFG_FPGA_CHECK_BUSY

1155 1156 1157 1158
		Enable checks on FPGA configuration interface busy
		status by the configuration function. This option
		will require a board or device specific function to
		be written.
wdenk's avatar
wdenk committed
1159 1160 1161

		CONFIG_FPGA_DELAY

1162 1163
		If defined, a function that provides delays in the
		FPGA configuration driver.
wdenk's avatar
wdenk committed
1164 1165 1166 1167 1168 1169 1170

		CFG_FPGA_CHECK_CTRLC

		Allow Control-C to interrupt FPGA configuration

		CFG_FPGA_CHECK_ERROR

1171 1172 1173 1174
		Check for configuration errors during FPGA bitfile
		loading. For example, abort during Virtex II
		configuration if the INIT_B line goes low (which
		indicated a CRC error).
wdenk's avatar
wdenk committed
1175 1176 1177

		CFG_FPGA_WAIT_INIT

1178 1179 1180
		Maximum time to wait for the INIT_B line to deassert
		after PROB_B has been deasserted during a Virtex II
		FPGA configuration sequence. The default time is 500 mS.
wdenk's avatar
wdenk committed
1181 1182 1183

		CFG_FPGA_WAIT_BUSY

1184 1185
		Maximum time to wait for BUSY to deassert during
		Virtex II FPGA configuration. The default is 5 mS.
wdenk's avatar
wdenk committed
1186 1187 1188

		CFG_FPGA_WAIT_CONFIG

1189
		Time to wait after FPGA configuration. The default is
wdenk's avatar
wdenk committed
1190 1191 1192 1193
		200 mS.

- FPGA Support:	CONFIG_FPGA_COUNT

wdenk's avatar
wdenk committed
1194
		Specify the number of FPGA devices to support.
wdenk's avatar
wdenk committed
1195

wdenk's avatar
wdenk committed
1196
		CONFIG_FPGA
wdenk's avatar
wdenk committed
1197

wdenk's avatar
wdenk committed
1198 1199
		Used to specify the types of FPGA devices.  For example,
		#define CONFIG_FPGA  CFG_XILINX_VIRTEX2
wdenk's avatar
wdenk committed
1200

wdenk's avatar
wdenk committed
1201
		CFG_FPGA_PROG_FEEDBACK
wdenk's avatar
wdenk committed
1202

wdenk's avatar
wdenk committed
1203
		Enable printing of hash marks during FPGA configuration.
wdenk's avatar
wdenk committed
1204 1205 1206

		CFG_FPGA_CHECK_BUSY

1207 1208 1209 1210
		Enable checks on FPGA configuration interface busy
		status by the configuration function. This option
		will require a board or device specific function to
		be written.
wdenk's avatar
wdenk committed
1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221

		CONFIG_FPGA_DELAY

		If defined, a function that provides delays in the FPGA
		configuration driver.

		CFG_FPGA_CHECK_CTRLC
		Allow Control-C to interrupt FPGA configuration

		CFG_FPGA_CHECK_ERROR

1222 1223 1224 1225
		Check for configuration errors during FPGA bitfile
		loading. For example, abort during Virtex II
		configuration if the INIT_B line goes low (which
		indicated a CRC error).
wdenk's avatar
wdenk committed
1226 1227 1228

		CFG_FPGA_WAIT_INIT

1229 1230 1231 1232
		Maximum time to wait for the INIT_B line to deassert
		after PROB_B has been deasserted during a Virtex II
		FPGA configuration sequence. The default time is 500
		mS.
wdenk's avatar
wdenk committed
1233 1234 1235

		CFG_FPGA_WAIT_BUSY

1236 1237
		Maximum time to wait for BUSY to deassert during
		Virtex II FPGA configuration. The default is 5 mS.
wdenk's avatar
wdenk committed
1238 1239 1240

		CFG_FPGA_WAIT_CONFIG

1241 1242
		Time to wait after FPGA configuration. The default is
		200 mS.
wdenk's avatar
wdenk committed
1243 1244 1245 1246

- Configuration Management:
		CONFIG_IDENT_STRING

1247 1248
		If defined, this string will be added to the U-Boot
		version information (U_BOOT_VERSION)
wdenk's avatar
wdenk committed
1249 1250 1251

- Vendor Parameter Protection:

1252 1253
		U-Boot considers the values of the environment
		variables "serial#" (Board Serial Number) and
wdenk's avatar
wdenk committed
1254
		"ethaddr" (Ethernet Address) to be parameters that
1255 1256 1257 1258 1259
		are set once by the board vendor / manufacturer, and
		protects these variables from casual modification by
		the user. Once set, these variables are read-only,
		and write or delete attempts are rejected. You can
		change this behviour:
wdenk's avatar
wdenk committed
1260 1261 1262

		If CONFIG_ENV_OVERWRITE is #defined in your config
		file, the write protection for vendor parameters is
1263
		completely disabled. Anybody can change or delete
wdenk's avatar
wdenk committed
1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318
		these parameters.

		Alternatively, if you #define _both_ CONFIG_ETHADDR
		_and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
		ethernet address is installed in the environment,
		which can be changed exactly ONCE by the user. [The
		serial# is unaffected by this, i. e. it remains
		read-only.]

- Protected RAM:
		CONFIG_PRAM

		Define this variable to enable the reservation of
		"protected RAM", i. e. RAM which is not overwritten
		by U-Boot. Define CONFIG_PRAM to hold the number of
		kB you want to reserve for pRAM. You can overwrite
		this default value by defining an environment
		variable "pram" to the number of kB you want to
		reserve. Note that the board info structure will
		still show the full amount of RAM. If pRAM is
		reserved, a new environment variable "mem" will
		automatically be defined to hold the amount of
		remaining RAM in a form that can be passed as boot
		argument to Linux, for instance like that:

			setenv bootargs ... mem=\$(mem)
			saveenv

		This way you can tell Linux not to use this memory,
		either, which results in a memory region that will
		not be affected by reboots.

		*WARNING* If your board configuration uses automatic
		detection of the RAM size, you must make sure that
		this memory test is non-destructive. So far, the
		following board configurations are known to be
		"pRAM-clean":

			ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
			HERMES, IP860, RPXlite, LWMON, LANTEC,
			PCU_E, FLAGADM, TQM8260

- Error Recovery:
		CONFIG_PANIC_HANG

		Define this variable to stop the system in case of a
		fatal error, so that you have to reset it manually.
		This is probably NOT a good idea for an embedded
		system where you want to system to reboot
		automatically as fast as possible, but it may be
		useful during development since you can try to debug
		the conditions that lead to the situation.

		CONFIG_NET_RETRY_COUNT

1319 1320 1321 1322
		This variable defines the number of retries for
		network operations like ARP, RARP, TFTP, or BOOTP
		before giving up the operation. If not defined, a
		default value of 5 is used.
wdenk's avatar
wdenk committed
1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344

- Command Interpreter:
		CFG_HUSH_PARSER

		Define this variable to enable the "hush" shell (from
		Busybox) as command line interpreter, thus enabling
		powerful command line syntax like
		if...then...else...fi conditionals or `&&' and '||'
		constructs ("shell scripts").

		If undefined, you get the old, much simpler behaviour
		with a somewhat smaller memory footprint.


		CFG_PROMPT_HUSH_PS2

		This defines the secondary prompt string, which is
		printed when the command interpreter needs more input
		to complete a command. Usually "> ".

	Note:

wdenk's avatar
wdenk committed
1345 1346 1347 1348 1349 1350 1351
		In the current implementation, the local variables
		space and global environment variables space are
		separated. Local variables are those you define by
		simply typing `name=value'. To access a local
		variable later on, you have write `$name' or
		`${name}'; to execute the contents of a variable
		directly type `$name' at the command prompt.
wdenk's avatar
wdenk committed
1352

1353 1354 1355 1356
		Global environment variables are those you use
		setenv/printenv to work with. To run a command stored
		in such a variable, you need to use the run command,
		and you must not use the '$' sign to access them.
wdenk's avatar
wdenk committed
1357 1358 1359 1360 1361 1362 1363

		To store commands and special characters in a
		variable, please use double quotation marks
		surrounding the whole text of the variable, instead
		of the backslashes before semicolons and special
		symbols.

wdenk's avatar
wdenk committed
1364
- Default Environment:
wdenk's avatar
wdenk committed
1365 1366
		CONFIG_EXTRA_ENV_SETTINGS

1367 1368
		Define this to contain any number of null terminated
		strings (variable = value pairs) that will be part of
wdenk's avatar
wdenk committed
1369
		the default environment compiled into the boot image.
1370

1371 1372
		For example, place something like this in your
		board's config file:
wdenk's avatar
wdenk committed
1373 1374 1375 1376 1377

		#define CONFIG_EXTRA_ENV_SETTINGS \
			"myvar1=value1\0" \
			"myvar2=value2\0"

1378 1379 1380 1381
		Warning: This method is based on knowledge about the
		internal format how the environment is stored by the
		U-Boot code. This is NOT an official, exported
		interface! Although it is unlikely that this format
wdenk's avatar
wdenk committed
1382
		will change soon, there is no guarantee either.
wdenk's avatar
wdenk committed
1383 1384
		You better know what you are doing here.

1385 1386 1387 1388
		Note: overly (ab)use of the default environment is
		discouraged. Make sure to check other ways to preset
		the environment like the autoscript function or the
		boot command first.
wdenk's avatar
wdenk committed
1389

wdenk's avatar
wdenk committed
1390
- DataFlash Support:
1391 1392
		CONFIG_HAS_DATAFLASH

wdenk's avatar
wdenk committed
1393 1394 1395
		Defining this option enables DataFlash features and
		allows to read/write in Dataflash via the standard
		commands cp, md...
1396

wdenk's avatar
wdenk committed
1397
- Show boot progress:
wdenk's avatar
wdenk committed
1398 1399
		CONFIG_SHOW_BOOT_PROGRESS

1400 1401 1402 1403 1404 1405
		Defining this option allows to add some board-
		specific code (calling a user-provided function
		"show_boot_progress(int)") that enables you to show
		the system's boot progress on some display (for
		example, some LED's) on your board. At the moment,
		the following checkpoints are implemented:
wdenk's avatar
wdenk committed
1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450

  Arg	Where			When
    1	common/cmd_bootm.c	before attempting to boot an image
   -1	common/cmd_bootm.c	Image header has bad     magic number
    2	common/cmd_bootm.c	Image header has correct magic number
   -2	common/cmd_bootm.c	Image header has bad     checksum
    3	common/cmd_bootm.c	Image header has correct checksum
   -3	common/cmd_bootm.c	Image data   has bad     checksum
    4	common/cmd_bootm.c	Image data   has correct checksum
   -4	common/cmd_bootm.c	Image is for unsupported architecture
    5	common/cmd_bootm.c	Architecture check OK
   -5	common/cmd_bootm.c	Wrong Image Type (not kernel, multi, standalone)
    6	common/cmd_bootm.c	Image Type check OK
   -6	common/cmd_bootm.c	gunzip uncompression error
   -7	common/cmd_bootm.c	Unimplemented compression type
    7	common/cmd_bootm.c	Uncompression OK
   -8	common/cmd_bootm.c	Wrong Image Type (not kernel, multi, standalone)
    8	common/cmd_bootm.c	Image Type check OK
   -9	common/cmd_bootm.c	Unsupported OS (not Linux, BSD, VxWorks, QNX)
    9	common/cmd_bootm.c	Start initial ramdisk verification
  -10	common/cmd_bootm.c	Ramdisk header has bad     magic number
  -11	common/cmd_bootm.c	Ramdisk header has bad     checksum
   10	common/cmd_bootm.c	Ramdisk header is OK
  -12	common/cmd_bootm.c	Ramdisk data   has bad     checksum
   11	common/cmd_bootm.c	Ramdisk data   has correct checksum
   12	common/cmd_bootm.c	Ramdisk verification complete, start loading
  -13	common/cmd_bootm.c	Wrong Image Type (not PPC Linux Ramdisk)
   13	common/cmd_bootm.c	Start multifile image verification
   14	common/cmd_bootm.c	No initial ramdisk, no multifile, continue.
   15	common/cmd_bootm.c	All preparation done, transferring control to OS

   -1	common/cmd_doc.c	Bad usage of "doc" command
   -1	common/cmd_doc.c	No boot device
   -1	common/cmd_doc.c	Unknown Chip ID on boot device
   -1	common/cmd_doc.c	Read Error on boot device
   -1	common/cmd_doc.c	Image header has bad magic number

   -1	common/cmd_ide.c	Bad usage of "ide" command
   -1	common/cmd_ide.c	No boot device
   -1	common/cmd_ide.c	Unknown boot device
   -1	common/cmd_ide.c	Unknown partition table
   -1	common/cmd_ide.c	Invalid partition type
   -1	common/cmd_ide.c	Read Error on boot device
   -1	common/cmd_ide.c	Image header has bad magic number

wdenk's avatar
wdenk committed
1451 1452 1453 1454 1455 1456 1457
   -1	common/cmd_nand.c	Bad usage of "nand" command
   -1	common/cmd_nand.c	No boot device
   -1	common/cmd_nand.c	Unknown Chip ID on boot device
   -1	common/cmd_nand.c	Read Error on boot device
   -1	common/cmd_nand.c	Image header has bad magic number

   -1	common/env_common.c     Environment has a bad CRC, using default
wdenk's avatar
wdenk committed
1458 1459 1460 1461 1462


Modem Support:
--------------

1463
[so far only for SMDK2400 and TRAB boards]
wdenk's avatar
wdenk committed
1464 1465 1466 1467 1468 1469 1470 1471 1472 1473

- Modem support endable:
		CONFIG_MODEM_SUPPORT

- RTS/CTS Flow control enable:
		CONFIG_HWFLOW

- Modem debug support:
		CONFIG_MODEM_SUPPORT_DEBUG

1474 1475
		Enables debugging stuff (char screen[1024], dbg())
		for modem support. Useful only with BDI2000.
wdenk's avatar
wdenk committed
1476

wdenk's avatar
wdenk committed
1477 1478
- Interrupt support (PPC):

wdenk's avatar
wdenk committed
1479 1480 1481 1482 1483 1484 1485 1486 1487 1488
		There are common interrupt_init() and timer_interrupt()
		for all PPC archs. interrupt_init() calls interrupt_init_cpu()
		for cpu specific initialization. interrupt_init_cpu()
		should set decrementer_count to appropriate value. If
		cpu resets decrementer automatically after interrupt
		(ppc4xx) it should set decrementer_count to zero.
		timer_interrupt() calls timer_interrupt_cpu() for cpu
		specific handling. If board has watchdog / status_led
		/ other_activity_monitor it works automatically from
		general timer_interrupt().
wdenk's avatar
wdenk committed
1489

wdenk's avatar
wdenk committed
1490 1491
- General:

1492 1493 1494 1495 1496 1497 1498
		In the target system modem support is enabled when a
		specific key (key combination) is pressed during
		power-on. Otherwise U-Boot will boot normally
		(autoboot). The key_pressed() fuction is called from
		board_init(). Currently key_pressed() is a dummy
		function, returning 1 and thus enabling modem
		initialization.
wdenk's avatar
wdenk committed
1499

1500 1501 1502 1503
		If there are no modem init strings in the
		environment, U-Boot proceed to autoboot; the
		previous output (banner, info printfs) will be
		supressed, though.
wdenk's avatar
wdenk committed
1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530

		See also: doc/README.Modem


Configuration Settings:
-----------------------

- CFG_LONGHELP: Defined when you want long help messages included;
		undefine this when you're short of memory.

- CFG_PROMPT:	This is what U-Boot prints on the console to
		prompt for user input.

- CFG_CBSIZE:	Buffer size for input from the Console

- CFG_PBSIZE:	Buffer size for Console output

- CFG_MAXARGS:	max. Number of arguments accepted for monitor commands

- CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
		the application (usually a Linux kernel) when it is
		booted

- CFG_BAUDRATE_TABLE:
		List of legal baudrate settings for this board.

- CFG_CONSOLE_INFO_QUIET
wdenk's avatar
wdenk committed
1531
		Suppress display of console information at boot.
wdenk's avatar
wdenk committed
1532 1533

- CFG_CONSOLE_IS_IN_ENV
wdenk's avatar
wdenk committed
1534 1535 1536
		If the board specific function
			extern int overwrite_console (void);
		returns 1, the stdin, stderr and stdout are switched to the
wdenk's avatar
wdenk committed
1537 1538 1539
		serial port, else the settings in the environment are used.

- CFG_CONSOLE_OVERWRITE_ROUTINE
wdenk's avatar
wdenk committed
1540
		Enable the call to overwrite_console().
wdenk's avatar
wdenk committed
1541 1542 1543 1544 1545 1546 1547 1548 1549

- CFG_CONSOLE_ENV_OVERWRITE
		Enable overwrite of previous console environment settings.

- CFG_MEMTEST_START, CFG_MEMTEST_END:
		Begin and End addresses of the area used by the
		simple memory test.

- CFG_ALT_MEMTEST:
wdenk's avatar
wdenk committed
1550
		Enable an alternate, more extensive memory test.
wdenk's avatar
wdenk committed
1551

1552 1553 1554 1555
- CFG_MEMTEST_SCRATCH:
		Scratch address used by the alternate memory test
		You only need to set this if address zero isn't writeable

wdenk's avatar
wdenk committed
1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578
- CFG_TFTP_LOADADDR:
		Default load address for network file downloads

- CFG_LOADS_BAUD_CHANGE:
		Enable temporary baudrate change while serial download

- CFG_SDRAM_BASE:
		Physical start address of SDRAM. _Must_ be 0 here.

- CFG_MBIO_BASE:
		Physical start address of Motherboard I/O (if using a
		Cogent motherboard)

- CFG_FLASH_BASE:
		Physical start address of Flash memory.

- CFG_MONITOR_BASE:
		Physical start address of boot monitor code (set by
		make config files to be same as the text base address
		(TEXT_BASE) used when linking) - same as
		CFG_FLASH_BASE when booting from flash.

- CFG_MONITOR_LEN:
wdenk's avatar