README 179 KB
Newer Older
wdenk's avatar
wdenk committed
1
#
2
# (C) Copyright 2000 - 2013
wdenk's avatar
wdenk committed
3 4
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
5
# SPDX-License-Identifier:	GPL-2.0+
wdenk's avatar
wdenk committed
6 7 8 9 10
#

Summary:
========

11
This directory contains the source code for U-Boot, a boot loader for
wdenk's avatar
wdenk committed
12 13 14 15
Embedded boards based on PowerPC, ARM, MIPS and several other
processors, which can be installed in a boot ROM and used to
initialize and test the hardware or to download and run application
code.
wdenk's avatar
wdenk committed
16 17

The development of U-Boot is closely related to Linux: some parts of
18 19
the source code originate in the Linux source tree, we have some
header files in common, and special provision has been made to
wdenk's avatar
wdenk committed
20 21 22 23 24 25 26 27 28 29 30 31 32 33
support booting of Linux images.

Some attention has been paid to make this software easily
configurable and extendable. For instance, all monitor commands are
implemented with the same call interface, so that it's very easy to
add new commands. Also, instead of permanently adding rarely used
code (for instance hardware test utilities) to the monitor, you can
load and run it dynamically.


Status:
=======

In general, all boards for which a configuration option exists in the
34
Makefile have been tested to some extent and can be considered
wdenk's avatar
wdenk committed
35 36
"working". In fact, many of them are used in production systems.

37 38 39 40
In case of problems see the CHANGELOG file to find out who contributed
the specific port. In addition, there are various MAINTAINERS files
scattered throughout the U-Boot source identifying the people or
companies responsible for various boards and subsystems.
wdenk's avatar
wdenk committed
41

42 43 44
Note: As of August, 2010, there is no longer a CHANGELOG file in the
actual U-Boot source tree; however, it can be created dynamically
from the Git log using:
45 46 47

	make CHANGELOG

wdenk's avatar
wdenk committed
48 49 50 51

Where to get help:
==================

52
In case you have questions about, problems with or contributions for
53
U-Boot, you should send a message to the U-Boot mailing list at
54 55 56 57
<u-boot@lists.denx.de>. There is also an archive of previous traffic
on the mailing list - please search the archive before asking FAQ's.
Please see http://lists.denx.de/pipermail/u-boot and
http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
wdenk's avatar
wdenk committed
58 59


60 61 62
Where to get source code:
=========================

63
The U-Boot source code is maintained in the Git repository at
64 65 66 67
git://www.denx.de/git/u-boot.git ; you can browse it online at
http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary

The "snapshot" links on this page allow you to download tarballs of
68
any version you might be interested in. Official releases are also
69 70 71
available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
directory.

72
Pre-built (and tested) images are available from
73 74 75
ftp://ftp.denx.de/pub/u-boot/images/


wdenk's avatar
wdenk committed
76 77 78 79
Where we come from:
===================

- start from 8xxrom sources
80
- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenk's avatar
wdenk committed
81 82 83 84 85 86 87
- clean up code
- make it easier to add custom boards
- make it possible to add other [PowerPC] CPUs
- extend functions, especially:
  * Provide extended interface to Linux boot loader
  * S-Record download
  * network boot
88
  * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
89
- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenk's avatar
wdenk committed
90
- add other CPU families (starting with ARM)
91
- create U-Boot project (http://sourceforge.net/projects/u-boot)
Magnus Lilja's avatar
Magnus Lilja committed
92
- current project page: see http://www.denx.de/wiki/U-Boot
93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114


Names and Spelling:
===================

The "official" name of this project is "Das U-Boot". The spelling
"U-Boot" shall be used in all written text (documentation, comments
in source files etc.). Example:

	This is the README file for the U-Boot project.

File names etc. shall be based on the string "u-boot". Examples:

	include/asm-ppc/u-boot.h

	#include <asm/u-boot.h>

Variable names, preprocessor constants etc. shall be either based on
the string "u_boot" or on "U_BOOT". Example:

	U_BOOT_VERSION		u_boot_logo
	IH_OS_U_BOOT		u_boot_hush_start
wdenk's avatar
wdenk committed
115 116


wdenk's avatar
wdenk committed
117 118 119
Versioning:
===========

120 121 122 123 124 125 126 127
Starting with the release in October 2008, the names of the releases
were changed from numerical release numbers without deeper meaning
into a time stamp based numbering. Regular releases are identified by
names consisting of the calendar year and month of the release date.
Additional fields (if present) indicate release candidates or bug fix
releases in "stable" maintenance trees.

Examples:
Wolfgang Denk's avatar
Wolfgang Denk committed
128
	U-Boot v2009.11	    - Release November 2009
129
	U-Boot v2009.11.1   - Release 1 in version November 2009 stable tree
130
	U-Boot v2010.09-rc1 - Release candidate 1 for September 2010 release
wdenk's avatar
wdenk committed
131 132


wdenk's avatar
wdenk committed
133 134 135
Directory Hierarchy:
====================

136
/arch			Architecture specific files
137
  /arc			Files generic to ARC architecture
138 139 140 141
  /arm			Files generic to ARM architecture
  /m68k			Files generic to m68k architecture
  /microblaze		Files generic to microblaze architecture
  /mips			Files generic to MIPS architecture
142
  /nds32		Files generic to NDS32 architecture
143
  /nios2		Files generic to Altera NIOS2 architecture
144
  /openrisc		Files generic to OpenRISC architecture
Stefan Roese's avatar
Stefan Roese committed
145
  /powerpc		Files generic to PowerPC architecture
146
  /riscv		Files generic to RISC-V architecture
147
  /sandbox		Files generic to HW-independent "sandbox"
148
  /sh			Files generic to SH architecture
149
  /x86			Files generic to x86 architecture
150 151
/api			Machine/arch independent API for external apps
/board			Board dependent files
152
/cmd			U-Boot commands functions
153
/common			Misc architecture independent functions
154
/configs		Board default configuration files
155 156 157
/disk			Code for disk drive partition handling
/doc			Documentation (don't expect too much)
/drivers		Commonly used device drivers
158
/dts			Contains Makefile for building internal U-Boot fdt.
159 160 161
/examples		Example code for standalone applications, etc.
/fs			Filesystem code (cramfs, ext2, jffs2, etc.)
/include		Header Files
162 163
/lib			Library routines generic to all architectures
/Licenses		Various license files
164 165
/net			Networking code
/post			Power On Self Test
166 167
/scripts		Various build scripts and Makefiles
/test			Various unit test files
168
/tools			Tools to build S-Record or U-Boot images, etc.
wdenk's avatar
wdenk committed
169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184

Software Configuration:
=======================

Configuration is usually done using C preprocessor defines; the
rationale behind that is to avoid dead code whenever possible.

There are two classes of configuration variables:

* Configuration _OPTIONS_:
  These are selectable by the user and have names beginning with
  "CONFIG_".

* Configuration _SETTINGS_:
  These depend on the hardware etc. and should not be meddled with if
  you don't know what you're doing; they have names beginning with
185
  "CONFIG_SYS_".
wdenk's avatar
wdenk committed
186

187 188 189 190 191
Previously, all configuration was done by hand, which involved creating
symbolic links and editing configuration files manually. More recently,
U-Boot has added the Kbuild infrastructure used by the Linux kernel,
allowing you to use the "make menuconfig" command to configure your
build.
wdenk's avatar
wdenk committed
192 193 194 195 196 197


Selection of Processor Architecture and Board Type:
---------------------------------------------------

For all supported boards there are ready-to-use default
198
configurations available; just type "make <board_name>_defconfig".
wdenk's avatar
wdenk committed
199 200 201 202

Example: For a TQM823L module type:

	cd u-boot
203
	make TQM823L_defconfig
wdenk's avatar
wdenk committed
204

205 206 207
Note: If you're looking for the default configuration file for a board
you're sure used to be there but is now missing, check the file
doc/README.scrapyard for a list of no longer supported boards.
wdenk's avatar
wdenk committed
208

209 210 211 212 213 214 215 216
Sandbox Environment:
--------------------

U-Boot can be built natively to run on a Linux host using the 'sandbox'
board. This allows feature development which is not board- or architecture-
specific to be undertaken on a native platform. The sandbox is also used to
run some of U-Boot's tests.

217
See board/sandbox/README.sandbox for more details.
218 219


220 221 222 223
Board Initialisation Flow:
--------------------------

This is the intended start-up flow for boards. This should apply for both
224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239
SPL and U-Boot proper (i.e. they both follow the same rules).

Note: "SPL" stands for "Secondary Program Loader," which is explained in
more detail later in this file.

At present, SPL mostly uses a separate code path, but the function names
and roles of each function are the same. Some boards or architectures
may not conform to this.  At least most ARM boards which use
CONFIG_SPL_FRAMEWORK conform to this.

Execution typically starts with an architecture-specific (and possibly
CPU-specific) start.S file, such as:

	- arch/arm/cpu/armv7/start.S
	- arch/powerpc/cpu/mpc83xx/start.S
	- arch/mips/cpu/start.S
240

241 242
and so on. From there, three functions are called; the purpose and
limitations of each of these functions are described below.
243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294

lowlevel_init():
	- purpose: essential init to permit execution to reach board_init_f()
	- no global_data or BSS
	- there is no stack (ARMv7 may have one but it will soon be removed)
	- must not set up SDRAM or use console
	- must only do the bare minimum to allow execution to continue to
		board_init_f()
	- this is almost never needed
	- return normally from this function

board_init_f():
	- purpose: set up the machine ready for running board_init_r():
		i.e. SDRAM and serial UART
	- global_data is available
	- stack is in SRAM
	- BSS is not available, so you cannot use global/static variables,
		only stack variables and global_data

	Non-SPL-specific notes:
	- dram_init() is called to set up DRAM. If already done in SPL this
		can do nothing

	SPL-specific notes:
	- you can override the entire board_init_f() function with your own
		version as needed.
	- preloader_console_init() can be called here in extremis
	- should set up SDRAM, and anything needed to make the UART work
	- these is no need to clear BSS, it will be done by crt0.S
	- must return normally from this function (don't call board_init_r()
		directly)

Here the BSS is cleared. For SPL, if CONFIG_SPL_STACK_R is defined, then at
this point the stack and global_data are relocated to below
CONFIG_SPL_STACK_R_ADDR. For non-SPL, U-Boot is relocated to run at the top of
memory.

board_init_r():
	- purpose: main execution, common code
	- global_data is available
	- SDRAM is available
	- BSS is available, all static/global variables can be used
	- execution eventually continues to main_loop()

	Non-SPL-specific notes:
	- U-Boot is relocated to the top of memory and is now running from
		there.

	SPL-specific notes:
	- stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
		CONFIG_SPL_STACK_R_ADDR points into SDRAM
	- preloader_console_init() can be called here - typically this is
295
		done by selecting CONFIG_SPL_BOARD_INIT and then supplying a
296 297 298 299 300
		spl_board_init() function containing this call
	- loads U-Boot or (in falcon mode) Linux



wdenk's avatar
wdenk committed
301 302 303 304 305 306 307 308 309 310 311
Configuration Options:
----------------------

Configuration depends on the combination of board and CPU type; all
such information is kept in a configuration file
"include/configs/<board_name>.h".

Example: For a TQM823L module, all configuration settings are in
"include/configs/TQM823L.h".


wdenk's avatar
wdenk committed
312 313 314 315
Many of the options are named exactly as the corresponding Linux
kernel configuration options. The intention is to make it easier to
build a config tool - later.

316 317 318 319 320 321 322 323 324
- ARM Platform Bus Type(CCI):
		CoreLink Cache Coherent Interconnect (CCI) is ARM BUS which
		provides full cache coherency between two clusters of multi-core
		CPUs and I/O coherency for devices and I/O masters

		CONFIG_SYS_FSL_HAS_CCI400

		Defined For SoC that has cache coherent interconnect
		CCN-400
wdenk's avatar
wdenk committed
325

326 327 328 329
		CONFIG_SYS_FSL_HAS_CCN504

		Defined for SoC that has cache coherent interconnect CCN-504

wdenk's avatar
wdenk committed
330 331
The following options need to be configured:

332 333 334
- CPU Type:	Define exactly one, e.g. CONFIG_MPC85XX.

- Board Type:	Define exactly one, e.g. CONFIG_MPC8540ADS.
335

336 337 338 339 340
- Marvell Family Member
		CONFIG_SYS_MVFS		- define it if you want to enable
					  multiple fs option at one time
					  for marvell soc family

341
- 85xx CPU Options:
342 343 344 345 346 347
		CONFIG_SYS_PPC64

		Specifies that the core is a 64-bit PowerPC implementation (implements
		the "64" category of the Power ISA). This is necessary for ePAPR
		compliance, among other possible reasons.

348 349 350 351 352 353
		CONFIG_SYS_FSL_TBCLK_DIV

		Defines the core time base clock divider ratio compared to the
		system clock.  On most PQ3 devices this is 8, on newer QorIQ
		devices it can be 16 or 32.  The ratio varies from SoC to Soc.

354 355 356 357 358
		CONFIG_SYS_FSL_PCIE_COMPAT

		Defines the string to utilize when trying to match PCIe device
		tree nodes for the given platform.

359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378
		CONFIG_SYS_FSL_ERRATUM_A004510

		Enables a workaround for erratum A004510.  If set,
		then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.

		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
		CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)

		Defines one or two SoC revisions (low 8 bits of SVR)
		for which the A004510 workaround should be applied.

		The rest of SVR is either not relevant to the decision
		of whether the erratum is present (e.g. p2040 versus
		p2041) or is implied by the build target, which controls
		whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.

		See Freescale App Note 4493 for more information about
		this erratum.

379 380
		CONFIG_A003399_NOR_WORKAROUND
		Enables a workaround for IFC erratum A003399. It is only
381
		required during NOR boot.
382

383 384
		CONFIG_A008044_WORKAROUND
		Enables a workaround for T1040/T1042 erratum A008044. It is only
385
		required during NAND boot and valid for Rev 1.0 SoC revision
386

387 388 389 390 391
		CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY

		This is the value to write into CCSR offset 0x18600
		according to the A004510 workaround.

392 393 394 395
		CONFIG_SYS_FSL_DSP_DDR_ADDR
		This value denotes start offset of DDR memory which is
		connected exclusively to the DSP cores.

396 397 398 399
		CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
		This value denotes start offset of M2 memory
		which is directly connected to the DSP core.

400 401 402 403
		CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
		This value denotes start offset of M3 memory which is directly
		connected to the DSP core.

404 405 406
		CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
		This value denotes start offset of DSP CCSR space.

407 408 409 410 411
		CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
		Single Source Clock is clocking mode present in some of FSL SoC's.
		In this mode, a single differential clock is used to supply
		clocks to the sysclock, ddrclock and usbclock.

412 413
		CONFIG_SYS_CPC_REINIT_F
		This CONFIG is defined when the CPC is configured as SRAM at the
Bin Meng's avatar
Bin Meng committed
414
		time of U-Boot entry and is required to be re-initialized.
415

416
		CONFIG_DEEP_SLEEP
417
		Indicates this SoC supports deep sleep feature. If deep sleep is
418 419
		supported, core will start to execute uboot when wakes up.

420 421 422 423 424 425
- Generic CPU options:
		CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN

		Defines the endianess of the CPU. Implementation of those
		values is arch specific.

426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446
		CONFIG_SYS_FSL_DDR
		Freescale DDR driver in use. This type of DDR controller is
		found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
		SoCs.

		CONFIG_SYS_FSL_DDR_ADDR
		Freescale DDR memory-mapped register base.

		CONFIG_SYS_FSL_DDR_EMU
		Specify emulator support for DDR. Some DDR features such as
		deskew training are not available.

		CONFIG_SYS_FSL_DDRC_GEN1
		Freescale DDR1 controller.

		CONFIG_SYS_FSL_DDRC_GEN2
		Freescale DDR2 controller.

		CONFIG_SYS_FSL_DDRC_GEN3
		Freescale DDR3 controller.

447 448 449
		CONFIG_SYS_FSL_DDRC_GEN4
		Freescale DDR4 controller.

450 451 452
		CONFIG_SYS_FSL_DDRC_ARM_GEN3
		Freescale DDR3 controller for ARM-based SoCs.

453 454 455 456 457 458
		CONFIG_SYS_FSL_DDR1
		Board config to use DDR1. It can be enabled for SoCs with
		Freescale DDR1 or DDR2 controllers, depending on the board
		implemetation.

		CONFIG_SYS_FSL_DDR2
459
		Board config to use DDR2. It can be enabled for SoCs with
460 461 462 463 464
		Freescale DDR2 or DDR3 controllers, depending on the board
		implementation.

		CONFIG_SYS_FSL_DDR3
		Board config to use DDR3. It can be enabled for SoCs with
465 466 467 468 469 470 471 472 473
		Freescale DDR3 or DDR3L controllers.

		CONFIG_SYS_FSL_DDR3L
		Board config to use DDR3L. It can be enabled for SoCs with
		DDR3L controllers.

		CONFIG_SYS_FSL_DDR4
		Board config to use DDR4. It can be enabled for SoCs with
		DDR4 controllers.
474

475 476 477 478 479 480
		CONFIG_SYS_FSL_IFC_BE
		Defines the IFC controller register space as Big Endian

		CONFIG_SYS_FSL_IFC_LE
		Defines the IFC controller register space as Little Endian

481 482 483
		CONFIG_SYS_FSL_IFC_CLK_DIV
		Defines divider of platform clock(clock input to IFC controller).

484 485 486
		CONFIG_SYS_FSL_LBC_CLK_DIV
		Defines divider of platform clock(clock input to eLBC controller).

487 488 489 490 491 492 493 494 495
		CONFIG_SYS_FSL_PBL_PBI
		It enables addition of RCW (Power on reset configuration) in built image.
		Please refer doc/README.pblimage for more details

		CONFIG_SYS_FSL_PBL_RCW
		It adds PBI(pre-boot instructions) commands in u-boot build image.
		PBI commands can be used to configure SoC before it starts the execution.
		Please refer doc/README.pblimage for more details

496 497 498 499
		CONFIG_SPL_FSL_PBL
		It adds a target to create boot binary having SPL binary in PBI format
		concatenated with u-boot binary.

500 501 502 503 504 505
		CONFIG_SYS_FSL_DDR_BE
		Defines the DDR controller register space as Big Endian

		CONFIG_SYS_FSL_DDR_LE
		Defines the DDR controller register space as Little Endian

506 507 508 509 510
		CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
		Physical address from the view of DDR controllers. It is the
		same as CONFIG_SYS_DDR_SDRAM_BASE for  all Power SoCs. But
		it could be different for ARM SoCs.

511 512 513 514 515
		CONFIG_SYS_FSL_DDR_INTLV_256B
		DDR controller interleaving on 256-byte. This is a special
		interleaving mode, handled by Dickens for Freescale layerscape
		SoCs with ARM core.

516 517 518 519 520 521
		CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
		Number of controllers used as main memory.

		CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
		Number of controllers used for other than main memory.

522 523 524
		CONFIG_SYS_FSL_HAS_DP_DDR
		Defines the SoC has DP-DDR used for DPAA.

525 526 527 528 529 530
		CONFIG_SYS_FSL_SEC_BE
		Defines the SEC controller register space as Big Endian

		CONFIG_SYS_FSL_SEC_LE
		Defines the SEC controller register space as Little Endian

531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562
- MIPS CPU options:
		CONFIG_SYS_INIT_SP_OFFSET

		Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
		pointer. This is needed for the temporary stack before
		relocation.

		CONFIG_SYS_MIPS_CACHE_MODE

		Cache operation mode for the MIPS CPU.
		See also arch/mips/include/asm/mipsregs.h.
		Possible values are:
			CONF_CM_CACHABLE_NO_WA
			CONF_CM_CACHABLE_WA
			CONF_CM_UNCACHED
			CONF_CM_CACHABLE_NONCOHERENT
			CONF_CM_CACHABLE_CE
			CONF_CM_CACHABLE_COW
			CONF_CM_CACHABLE_CUW
			CONF_CM_CACHABLE_ACCELERATED

		CONFIG_SYS_XWAY_EBU_BOOTCFG

		Special option for Lantiq XWAY SoCs for booting from NOR flash.
		See also arch/mips/cpu/mips32/start.S.

		CONFIG_XWAY_SWAP_BYTES

		Enable compilation of tools/xway-swap-bytes needed for Lantiq
		XWAY SoCs for booting from NOR flash. The U-Boot image needs to
		be swapped if a flash programmer is used.

563 564 565 566 567 568
- ARM options:
		CONFIG_SYS_EXCEPTION_VECTORS_HIGH

		Select high exception vectors of the ARM core, e.g., do not
		clear the V bit of the c1 register of CP15.

569 570 571 572 573 574 575 576
		COUNTER_FREQUENCY
		Generic timer clock source frequency.

		COUNTER_FREQUENCY_REAL
		Generic timer clock source frequency if the real clock is
		different from COUNTER_FREQUENCY, and can only be determined
		at run time.

577 578 579 580 581 582 583
- Tegra SoC options:
		CONFIG_TEGRA_SUPPORT_NON_SECURE

		Support executing U-Boot in non-secure (NS) mode. Certain
		impossible actions will be skipped if the CPU is in NS mode,
		such as ARM architectural timer initialization.

584
- Linux Kernel Interface:
wdenk's avatar
wdenk committed
585 586 587 588 589 590 591 592 593 594
		CONFIG_CLOCKS_IN_MHZ

		U-Boot stores all clock information in Hz
		internally. For binary compatibility with older Linux
		kernels (which expect the clocks passed in the
		bd_info data to be in MHz) the environment variable
		"clocks_in_mhz" can be defined so that U-Boot
		converts clock data to MHZ before passing it to the
		Linux kernel.
		When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
595
		"clocks_in_mhz=1" is automatically included in the
wdenk's avatar
wdenk committed
596 597
		default environment.

598 599
		CONFIG_MEMSIZE_IN_BYTES		[relevant for MIPS only]

600
		When transferring memsize parameter to Linux, some versions
601 602 603
		expect it to be in bytes, others in MB.
		Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.

604
		CONFIG_OF_LIBFDT
605 606

		New kernel versions are expecting firmware settings to be
607 608 609 610 611 612
		passed using flattened device trees (based on open firmware
		concepts).

		CONFIG_OF_LIBFDT
		 * New libfdt-based support
		 * Adds the "fdt" command
613
		 * The bootm command automatically updates the fdt
614

615
		OF_TBCLK - The timebase frequency.
Kumar Gala's avatar
Kumar Gala committed
616
		OF_STDOUT_PATH - The path to the console device
617

618 619
		boards with QUICC Engines require OF_QE to set UCC MAC
		addresses
620

621 622 623 624
		CONFIG_OF_BOARD_SETUP

		Board code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel
625

626 627 628 629 630 631 632
		CONFIG_OF_SYSTEM_SETUP

		Other code has addition modification that it wants to make
		to the flat device tree before handing it off to the kernel.
		This causes ft_system_setup() to be called before booting
		the kernel.

633 634 635 636 637 638 639 640 641
		CONFIG_OF_IDE_FIXUP

		U-Boot can detect if an IDE device is present or not.
		If not, and this new config option is activated, U-Boot
		removes the ATA node from the DTS before booting Linux,
		so the Linux IDE driver does not probe the device and
		crash. This is needed for buggy hardware (uc101) where
		no pull down resistor is connected to the signal IDE5V_DD7.

642 643 644 645 646 647 648 649 650 651
		CONFIG_MACH_TYPE	[relevant for ARM only][mandatory]

		This setting is mandatory for all boards that have only one
		machine type and must be used to specify the machine type
		number as it appears in the ARM machine registry
		(see http://www.arm.linux.org.uk/developer/machines/).
		Only boards that have multiple machine types supported
		in a single configuration file and the machine type is
		runtime discoverable, do not have to use this setting.

652 653 654
- vxWorks boot parameters:

		bootvx constructs a valid bootline using the following
655 656
		environments variables: bootdev, bootfile, ipaddr, netmask,
		serverip, gatewayip, hostname, othbootargs.
657 658 659 660 661
		It loads the vxWorks image pointed bootfile.

		Note: If a "bootargs" environment is defined, it will overwride
		the defaults discussed just above.

662 663 664 665 666
- Cache Configuration:
		CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
		CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
		CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot

667 668 669 670 671 672
- Cache Configuration for ARM:
		CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
				      controller
		CONFIG_SYS_PL310_BASE - Physical base address of PL310
					controller register space

673
- Serial Ports:
674
		CONFIG_PL010_SERIAL
675 676 677

		Define this if you want support for Amba PrimeCell PL010 UARTs.

678
		CONFIG_PL011_SERIAL
679 680 681 682 683 684 685 686 687 688 689 690 691 692

		Define this if you want support for Amba PrimeCell PL011 UARTs.

		CONFIG_PL011_CLOCK

		If you have Amba PrimeCell PL011 UARTs, set this variable to
		the clock speed of the UARTs.

		CONFIG_PL01x_PORTS

		If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
		define this to a list of base addresses for each (supported)
		port. See e.g. include/configs/versatile.h

693 694 695 696
		CONFIG_SERIAL_HW_FLOW_CONTROL

		Define this variable to enable hw flow control in serial driver.
		Current user of this option is drivers/serial/nsl16550.c driver
697

wdenk's avatar
wdenk committed
698 699 700
- Console Baudrate:
		CONFIG_BAUDRATE - in bps
		Select one of the baudrates listed in
701
		CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
702 703 704 705 706 707 708 709 710

- Autoboot Command:
		CONFIG_BOOTCOMMAND
		Only needed when CONFIG_BOOTDELAY is enabled;
		define a command string that is automatically executed
		when no character is read on the console interface
		within "Boot Delay" after reset.

		CONFIG_RAMBOOT and CONFIG_NFSBOOT
711 712 713
		The value of these goes into the environment as
		"ramboot" and "nfsboot" respectively, and can be used
		as a convenience, when switching between booting from
714
		RAM and NFS.
wdenk's avatar
wdenk committed
715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740

- Pre-Boot Commands:
		CONFIG_PREBOOT

		When this option is #defined, the existence of the
		environment variable "preboot" will be checked
		immediately before starting the CONFIG_BOOTDELAY
		countdown and/or running the auto-boot command resp.
		entering interactive mode.

		This feature is especially useful when "preboot" is
		automatically generated or modified. For an example
		see the LWMON board specific code: here "preboot" is
		modified when the user holds down a certain
		combination of keys on the (special) keyboard when
		booting the systems

- Serial Download Echo Mode:
		CONFIG_LOADS_ECHO
		If defined to 1, all characters received during a
		serial download (using the "loads" command) are
		echoed back. This might be needed by some terminal
		emulations (like "cu"), but may as well just take
		time on others. This setting #define's the initial
		value of the "loads_echo" environment variable.

741
- Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
wdenk's avatar
wdenk committed
742 743
		CONFIG_KGDB_BAUDRATE
		Select one of the baudrates listed in
744
		CONFIG_SYS_BAUDRATE_TABLE, see below.
wdenk's avatar
wdenk committed
745

746 747 748 749 750 751 752 753
- Removal of commands
		If no commands are needed to boot, you can disable
		CONFIG_CMDLINE to remove them. In this case, the command line
		will not be available, and when U-Boot wants to execute the
		boot command (on start-up) it will call board_run_command()
		instead. This can reduce image size significantly for very
		simple boot procedures.

754 755
- Regular expression support:
		CONFIG_REGEX
756 757 758 759
		If this variable is defined, U-Boot is linked against
		the SLRE (Super Light Regular Expression) library,
		which adds regex support to some commands, as for
		example "env grep" and "setexpr".
760

761 762 763 764 765 766 767 768
- Device tree:
		CONFIG_OF_CONTROL
		If this variable is defined, U-Boot will use a device tree
		to configure its devices, instead of relying on statically
		compiled #defines in the board file. This option is
		experimental and only available on a few boards. The device
		tree is available in the global data as gd->fdt_blob.

769
		U-Boot needs to get its device tree from somewhere. This can
770
		be done using one of the three options below:
771 772 773 774 775 776

		CONFIG_OF_EMBED
		If this variable is defined, U-Boot will embed a device tree
		binary in its image. This device tree file should be in the
		board directory and called <soc>-<board>.dts. The binary file
		is then picked up in board_init_f() and made available through
777
		the global data structure as gd->fdt_blob.
778

779 780 781 782 783 784 785 786 787 788 789 790
		CONFIG_OF_SEPARATE
		If this variable is defined, U-Boot will build a device tree
		binary. It will be called u-boot.dtb. Architecture-specific
		code will locate it at run-time. Generally this works by:

			cat u-boot.bin u-boot.dtb >image.bin

		and in fact, U-Boot does this for you, creating a file called
		u-boot-dtb.bin which is useful in the common case. You can
		still use the individual files if you need something more
		exotic.

791 792 793 794 795 796
		CONFIG_OF_BOARD
		If this variable is defined, U-Boot will use the device tree
		provided by the board at runtime instead of embedding one with
		the image. Only boards defining board_fdt_blob_setup() support
		this option (see include/fdtdec.h file).

wdenk's avatar
wdenk committed
797 798 799
- Watchdog:
		CONFIG_WATCHDOG
		If this variable is defined, it enables watchdog
800
		support for the SoC. There must be support in the SoC
801 802 803 804 805
		specific code for a watchdog. For the 8xx
		CPUs, the SIU Watchdog feature is enabled in the SYPCR
		register.  When supported for a specific SoC is
		available, then no further board specific code should
		be needed to use it.
806 807 808 809 810

		CONFIG_HW_WATCHDOG
		When using a watchdog circuitry external to the used
		SoC, then define this variable and provide board
		specific code for the "hw_watchdog_reset" function.
wdenk's avatar
wdenk committed
811

812 813 814
		CONFIG_AT91_HW_WDT_TIMEOUT
		specify the timeout in seconds. default 2 seconds.

815 816 817 818 819
- U-Boot Version:
		CONFIG_VERSION_VARIABLE
		If this variable is defined, an environment variable
		named "ver" is created by U-Boot showing the U-Boot
		version as printed by the "version" command.
820 821
		Any change to this variable will be reverted at the
		next reset.
822

wdenk's avatar
wdenk committed
823 824
- Real-Time Clock:

825
		When CONFIG_CMD_DATE is selected, the type of the RTC
wdenk's avatar
wdenk committed
826 827 828 829
		has to be selected, too. Define exactly one of the
		following options:

		CONFIG_RTC_PCF8563	- use Philips PCF8563 RTC
830
		CONFIG_RTC_MC13XXX	- use MC13783 or MC13892 RTC
wdenk's avatar
wdenk committed
831
		CONFIG_RTC_MC146818	- use MC146818 RTC
832
		CONFIG_RTC_DS1307	- use Maxim, Inc. DS1307 RTC
wdenk's avatar
wdenk committed
833
		CONFIG_RTC_DS1337	- use Maxim, Inc. DS1337 RTC
834
		CONFIG_RTC_DS1338	- use Maxim, Inc. DS1338 RTC
835
		CONFIG_RTC_DS1339	- use Maxim, Inc. DS1339 RTC
836
		CONFIG_RTC_DS164x	- use Dallas DS164x RTC
837
		CONFIG_RTC_ISL1208	- use Intersil ISL1208 RTC
838
		CONFIG_RTC_MAX6900	- use Maxim, Inc. MAX6900 RTC
839
		CONFIG_RTC_DS1337_NOOSC	- Turn off the OSC output for DS1337
840 841
		CONFIG_SYS_RV3029_TCR	- enable trickle charger on
					  RV3029 RTC.
wdenk's avatar
wdenk committed
842

wdenk's avatar
wdenk committed
843 844 845
		Note that if the RTC uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

846 847 848
- GPIO Support:
		CONFIG_PCA953X		- use NXP's PCA953X series I2C GPIO

849 850 851 852
		The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
		chip-ngpio pairs that tell the PCA953X driver the number of
		pins supported by a particular chip.

853 854 855
		Note that if the GPIO device uses I2C, then the I2C interface
		must also be configured. See I2C Support, below.

Simon Glass's avatar
Simon Glass committed
856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877
- I/O tracing:
		When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
		accesses and can checksum them or write a list of them out
		to memory. See the 'iotrace' command for details. This is
		useful for testing device drivers since it can confirm that
		the driver behaves the same way before and after a code
		change. Currently this is supported on sandbox and arm. To
		add support for your architecture, add '#include <iotrace.h>'
		to the bottom of arch/<arch>/include/asm/io.h and test.

		Example output from the 'iotrace stats' command is below.
		Note that if the trace buffer is exhausted, the checksum will
		still continue to operate.

			iotrace is enabled
			Start:  10000000	(buffer start address)
			Size:   00010000	(buffer size)
			Offset: 00000120	(current buffer offset)
			Output: 10000120	(start + offset)
			Count:  00000018	(number of trace records)
			CRC32:  9526fb66	(CRC32 of all trace records)

wdenk's avatar
wdenk committed
878 879
- Timestamp Support:

880 881 882
		When CONFIG_TIMESTAMP is selected, the timestamp
		(date and time) of an image is printed by image
		commands like bootm or iminfo. This option is
883
		automatically enabled when you select CONFIG_CMD_DATE .
wdenk's avatar
wdenk committed
884

885 886 887 888 889 890 891 892
- Partition Labels (disklabels) Supported:
		Zero or more of the following:
		CONFIG_MAC_PARTITION   Apple's MacOS partition table.
		CONFIG_ISO_PARTITION   ISO partition table, used on CDROM etc.
		CONFIG_EFI_PARTITION   GPT partition table, common when EFI is the
				       bootloader.  Note 2TB partition limit; see
				       disk/part_efi.c
		CONFIG_MTD_PARTITIONS  Memory Technology Device partition table.
wdenk's avatar
wdenk committed
893

894
		If IDE or SCSI support is enabled (CONFIG_IDE or
895
		CONFIG_SCSI) you must configure support for at
896
		least one non-MTD partition type as well.
wdenk's avatar
wdenk committed
897 898

- IDE Reset method:
899 900
		CONFIG_IDE_RESET_ROUTINE - this is defined in several
		board configurations files but used nowhere!
wdenk's avatar
wdenk committed
901

902 903 904 905
		CONFIG_IDE_RESET - is this is defined, IDE Reset will
		be performed by calling the function
			ide_set_reset(int reset)
		which has to be defined in a board specific file
wdenk's avatar
wdenk committed
906 907 908 909 910 911

- ATAPI Support:
		CONFIG_ATAPI

		Set this to enable ATAPI support.

912 913 914 915
- LBA48 Support
		CONFIG_LBA48

		Set this to enable support for disks larger than 137GB
916
		Also look at CONFIG_SYS_64BIT_LBA.
917 918 919
		Whithout these , LBA48 support uses 32bit variables and will 'only'
		support disks up to 2.1TB.

920
		CONFIG_SYS_64BIT_LBA:
921 922 923
			When enabled, makes the IDE subsystem use 64bit sector addresses.
			Default is 32bit.

wdenk's avatar
wdenk committed
924
- SCSI Support:
925 926 927
		CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
		CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
		CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
wdenk's avatar
wdenk committed
928 929 930
		maximum numbers of LUNs, SCSI ID's and target
		devices.

931 932
		The environment variable 'scsidevs' is set to the number of
		SCSI devices found during the last scan.
933

wdenk's avatar
wdenk committed
934
- NETWORK Support (PCI):
935
		CONFIG_E1000
936 937 938 939 940 941 942 943 944 945 946
		Support for Intel 8254x/8257x gigabit chips.

		CONFIG_E1000_SPI
		Utility code for direct access to the SPI bus on Intel 8257x.
		This does not do anything useful unless you set at least one
		of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.

		CONFIG_E1000_SPI_GENERIC
		Allow generic access to the SPI bus on the Intel 8257x, for
		example with the "sspi" command.

wdenk's avatar
wdenk committed
947 948
		CONFIG_EEPRO100
		Support for Intel 82557/82559/82559ER chips.
949
		Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
wdenk's avatar
wdenk committed
950 951 952 953 954 955 956 957 958 959 960 961 962
		write routine for first time initialisation.

		CONFIG_TULIP
		Support for Digital 2114x chips.
		Optional CONFIG_TULIP_SELECT_MEDIA for board specific
		modem chip initialisation (KS8761/QS6611).

		CONFIG_NATSEMI
		Support for National dp83815 chips.

		CONFIG_NS8382X
		Support for National dp8382[01] gigabit chips.

963 964
- NETWORK Support (other):

965 966 967 968 969 970 971 972 973 974
		CONFIG_DRIVER_AT91EMAC
		Support for AT91RM9200 EMAC.

			CONFIG_RMII
			Define this to use reduced MII inteface

			CONFIG_DRIVER_AT91EMAC_QUIET
			If this defined, the driver is quiet.
			The driver doen't show link status messages.

Rob Herring's avatar
Rob Herring committed
975 976 977
		CONFIG_CALXEDA_XGMAC
		Support for the Calxeda XGMAC device

978
		CONFIG_LAN91C96
979 980 981 982 983
		Support for SMSC's LAN91C96 chips.

			CONFIG_LAN91C96_USE_32_BIT
			Define this to enable 32 bit addressing

984
		CONFIG_SMC91111
985 986 987 988 989 990 991 992 993 994 995 996 997
		Support for SMSC's LAN91C111 chip

			CONFIG_SMC91111_BASE
			Define this to hold the physical address
			of the device (I/O space)

			CONFIG_SMC_USE_32_BIT
			Define this if data bus is 32 bits

			CONFIG_SMC_USE_IOFUNCS
			Define this to use i/o functions instead of macros
			(some hardware wont work with macros)

998 999 1000 1001 1002 1003
		CONFIG_DRIVER_TI_EMAC
		Support for davinci emac

			CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
			Define this if you have more then 3 PHYs.

1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015
		CONFIG_FTGMAC100
		Support for Faraday's FTGMAC100 Gigabit SoC Ethernet

			CONFIG_FTGMAC100_EGIGA
			Define this to use GE link update with gigabit PHY.
			Define this if FTGMAC100 is connected to gigabit PHY.
			If your system has 10/100 PHY only, it might not occur
			wrong behavior. Because PHY usually return timeout or
			useless data when polling gigabit status and gigabit
			control registers. This behavior won't affect the
			correctnessof 10/100 link speed update.

1016 1017 1018 1019 1020 1021 1022 1023 1024
		CONFIG_SH_ETHER
		Support for Renesas on-chip Ethernet controller

			CONFIG_SH_ETHER_USE_PORT
			Define the number of ports to be used

			CONFIG_SH_ETHER_PHY_ADDR
			Define the ETH PHY's address

1025 1026 1027
			CONFIG_SH_ETHER_CACHE_WRITEBACK
			If this option is set, the driver enables cache flush.

1028 1029
- PWM Support:
		CONFIG_PWM_IMX
1030
		Support for PWM module on the imx6.
1031

1032
- TPM Support:
1033 1034 1035
		CONFIG_TPM
		Support TPM devices.

1036 1037
		CONFIG_TPM_TIS_INFINEON
		Support for Infineon i2c bus TPM devices. Only one device
1038 1039 1040 1041 1042
		per system is supported at this time.

			CONFIG_TPM_TIS_I2C_BURST_LIMITATION
			Define the burst count bytes upper limit

1043 1044 1045 1046 1047 1048 1049
		CONFIG_TPM_ST33ZP24
		Support for STMicroelectronics TPM devices. Requires DM_TPM support.

			CONFIG_TPM_ST33ZP24_I2C
			Support for STMicroelectronics ST33ZP24 I2C devices.
			Requires TPM_ST33ZP24 and I2C.

1050 1051 1052 1053
			CONFIG_TPM_ST33ZP24_SPI
			Support for STMicroelectronics ST33ZP24 SPI devices.
			Requires TPM_ST33ZP24 and SPI.

Dirk Eibach's avatar
Dirk Eibach committed
1054 1055 1056
		CONFIG_TPM_ATMEL_TWI
		Support for Atmel TWI TPM device. Requires I2C support.

1057
		CONFIG_TPM_TIS_LPC
1058 1059 1060 1061 1062 1063 1064 1065
		Support for generic parallel port TPM devices. Only one device
		per system is supported at this time.

			CONFIG_TPM_TIS_BASE_ADDRESS
			Base address where the generic TPM device is mapped
			to. Contemporary x86 systems usually map it at
			0xfed40000.

1066 1067 1068 1069 1070 1071 1072 1073 1074
		CONFIG_TPM
		Define this to enable the TPM support library which provides
		functional interfaces to some TPM commands.
		Requires support for a TPM device.

		CONFIG_TPM_AUTH_SESSIONS
		Define this to enable authorized functions in the TPM library.
		Requires CONFIG_TPM and CONFIG_SHA1.

wdenk's avatar
wdenk committed
1075 1076
- USB Support:
		At the moment only the UHCI host controller is
1077
		supported (PIP405, MIP405); define
wdenk's avatar
wdenk committed
1078 1079
		CONFIG_USB_UHCI to enable it.
		define CONFIG_USB_KEYBOARD to enable the USB Keyboard
wdenk's avatar
wdenk committed
1080
		and define CONFIG_USB_STORAGE to enable the USB
wdenk's avatar
wdenk committed
1081 1082 1083 1084
		storage devices.
		Note:
		Supported are USB Keyboards and USB Floppy drives
		(TEAC FD-05PUB).
1085

1086 1087 1088
		CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
		txfilltuning field in the EHCI controller on reset.

1089 1090 1091
		CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
		HW module registers.

Wolfgang Denk's avatar
Wolfgang Denk committed
1092 1093 1094 1095
- USB Device:
		Define the below if you wish to use the USB console.
		Once firmware is rebuilt from a serial console issue the
		command "setenv stdin usbtty; setenv stdout usbtty" and
1096
		attach your USB cable. The Unix command "dmesg" should print
Wolfgang Denk's avatar
Wolfgang Denk committed
1097 1098
		it has found a new device. The environment variable usbtty
		can be set to gserial or cdc_acm to enable your device to
Wolfgang Denk's avatar
Wolfgang Denk committed
1099
		appear to a USB host as a Linux gserial device or a
Wolfgang Denk's avatar
Wolfgang Denk committed
1100 1101 1102 1103 1104 1105 1106
		Common Device Class Abstract Control Model serial device.
		If you select usbtty = gserial you should be able to enumerate
		a Linux host by
		# modprobe usbserial vendor=0xVendorID product=0xProductID
		else if using cdc_acm, simply setting the environment
		variable usbtty to be cdc_acm should suffice. The following
		might be defined in YourBoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1107

Wolfgang Denk's avatar
Wolfgang Denk committed
1108 1109 1110 1111 1112 1113
			CONFIG_USB_DEVICE
			Define this to build a UDC device

			CONFIG_USB_TTY
			Define this to have a tty type of device available to
			talk to the UDC device
Wolfgang Denk's avatar
Wolfgang Denk committed
1114

1115 1116 1117 1118 1119 1120 1121 1122
			CONFIG_USBD_HS
			Define this to enable the high speed support for usb
			device and usbtty. If this feature is enabled, a routine
			int is_usbd_high_speed(void)
			also needs to be defined by the driver to dynamically poll
			whether the enumeration has succeded at high speed or full
			speed.

1123
			CONFIG_SYS_CONSOLE_IS_IN_ENV
Wolfgang Denk's avatar
Wolfgang Denk committed
1124 1125 1126
			Define this if you want stdin, stdout &/or stderr to
			be set to usbtty.

Wolfgang Denk's avatar
Wolfgang Denk committed
1127
		If you have a USB-IF assigned VendorID then you may wish to
Wolfgang Denk's avatar
Wolfgang Denk committed
1128
		define your own vendor specific values either in BoardName.h
Wolfgang Denk's avatar
Wolfgang Denk committed
1129
		or directly in usbd_vendor_info.h. If you don't define
Wolfgang Denk's avatar
Wolfgang Denk committed
1130 1131 1132 1133 1134 1135 1136
		CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
		CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
		should pretend to be a Linux device to it's target host.

			CONFIG_USBD_MANUFACTURER
			Define this string as the name of your company for
			- CONFIG_USBD_MANUFACTURER "my company"
Wolfgang Denk's avatar
Wolfgang Denk committed
1137

Wolfgang Denk's avatar
Wolfgang Denk committed
1138 1139 1140 1141 1142 1143 1144 1145 1146
			CONFIG_USBD_PRODUCT_NAME
			Define this string as the name of your product
			- CONFIG_USBD_PRODUCT_NAME "acme usb device"

			CONFIG_USBD_VENDORID
			Define this as your assigned Vendor ID from the USB
			Implementors Forum. This *must* be a genuine Vendor ID
			to avoid polluting the USB namespace.
			- CONFIG_USBD_VENDORID 0xFFFF
Wolfgang Denk's avatar
Wolfgang Denk committed
1147

Wolfgang Denk's avatar
Wolfgang Denk committed
1148 1149 1150 1151
			CONFIG_USBD_PRODUCTID
			Define this as the unique Product ID
			for your device
			- CONFIG_USBD_PRODUCTID 0xFFFF
1152

1153 1154 1155 1156 1157 1158 1159 1160
- ULPI Layer Support:
		The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
		the generic ULPI layer. The generic layer accesses the ULPI PHY
		via the platform viewport, so you need both the genric layer and
		the viewport enabled. Currently only Chipidea/ARC based
		viewport is supported.
		To enable the ULPI layer support, define CONFIG_USB_ULPI and
		CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1161 1162 1163
		If your ULPI phy needs a different reference clock than the
		standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
		the appropriate value in Hz.
wdenk's avatar
wdenk committed
1164

1165
- MMC Support:
wdenk's avatar
wdenk committed
1166 1167 1168
		The MMC controller on the Intel PXA is supported. To
		enable this define CONFIG_MMC. The MMC can be
		accessed from the boot prompt by mapping the device
1169
		to physical memory similar to flash. Command line is
1170 1171
		enabled with CONFIG_CMD_MMC. The MMC driver also works with
		the FAT fs. This is enabled with CONFIG_CMD_FAT.
1172

1173 1174 1175 1176 1177 1178 1179 1180 1181
		CONFIG_SH_MMCIF
		Support for Renesas on-chip MMCIF controller

			CONFIG_SH_MMCIF_ADDR
			Define the base address of MMCIF registers

			CONFIG_SH_MMCIF_CLK
			Define the clock frequency for MMCIF

1182 1183 1184 1185 1186 1187 1188
		CONFIG_SUPPORT_EMMC_BOOT
		Enable some additional features of the eMMC boot partitions.

		CONFIG_SUPPORT_EMMC_RPMB
		Enable the commands for reading, writing and programming the
		key for the Replay Protection Memory Block partition in eMMC.

1189
- USB Device Firmware Update (DFU) class support:
1190
		CONFIG_DFU_OVER_USB
1191 1192 1193 1194 1195
		This enables the USB portion of the DFU USB class

		CONFIG_DFU_MMC
		This enables support for exposing (e)MMC devices via DFU.

1196 1197 1198
		CONFIG_DFU_NAND
		This enables support for exposing NAND devices via DFU.

Afzal Mohammed's avatar
Afzal Mohammed committed
1199 1200 1201 1202 1203 1204
		CONFIG_DFU_RAM
		This enables support for exposing RAM via DFU.
		Note: DFU spec refer to non-volatile memory usage, but
		allow usages beyond the scope of spec - here RAM usage,
		one that would help mostly the developer.

1205 1206 1207 1208 1209 1210
		CONFIG_SYS_DFU_DATA_BUF_SIZE
		Dfu transfer uses a buffer before writing data to the
		raw storage device. Make the size (in bytes) of this buffer
		configurable. The size of this buffer is also configurable
		through the "dfu_bufsiz" environment variable.

1211 1212 1213 1214 1215 1216 1217
		CONFIG_SYS_DFU_MAX_FILE_SIZE
		When updating files rather than the raw storage device,
		we use a static buffer to copy the file into and then write
		the buffer once we've been given the whole file.  Define
		this to the maximum filesize (in bytes) for the buffer.
		Default is 4 MiB if undefined.

1218 1219 1220 1221 1222 1223 1224 1225 1226 1227
		DFU_DEFAULT_POLL_TIMEOUT
		Poll timeout [ms], is the timeout a device can send to the
		host. The host must wait for this timeout before sending
		a subsequent DFU_GET_STATUS request to the device.

		DFU_MANIFEST_POLL_TIMEOUT
		Poll timeout [ms], which the device sends to the host when
		entering dfuMANIFEST state. Host waits this timeout, before
		sending again an USB request to the device.

1228
- Journaling Flash filesystem support:
1229
		CONFIG_JFFS2_NAND
1230 1231
		Define these for a default partition on a NAND device

1232 1233
		CONFIG_SYS_JFFS2_FIRST_SECTOR,
		CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1234 1235
		Define these for a default partition on a NOR device

wdenk's avatar
wdenk committed
1236
- Keyboard Support:
1237 1238 1239 1240 1241 1242 1243 1244 1245
		See Kconfig help for available keyboard drivers.

		CONFIG_KEYBOARD

		Define this to enable a custom keyboard support.
		This simply calls drv_keyboard_init() which must be
		defined in your board-specific files. This option is deprecated
		and is only used by novena. For new boards, use driver model
		instead.
wdenk's avatar
wdenk committed
1246 1247

- Video support:
1248
		CONFIG_FSL_DIU_FB
Wolfgang Denk's avatar
Wolfgang Denk committed
1249
		Enable the Freescale DIU video driver.	Reference boards for
1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260
		SOCs that have a DIU should define this macro to enable DIU
		support, and should also define these other macros:

			CONFIG_SYS_DIU_ADDR
			CONFIG_VIDEO
			CONFIG_CFB_CONSOLE
			CONFIG_VIDEO_SW_CURSOR
			CONFIG_VGA_AS_SINGLE_DEVICE
			CONFIG_VIDEO_LOGO
			CONFIG_VIDEO_BMP_LOGO

1261 1262
		The DIU driver will look for the 'video-mode' environment
		variable, and if defined, enable the DIU as a console during
1263
		boot.  See the documentation file doc/README.video for a
1264
		description of this variable.
1265

wdenk's avatar
wdenk committed
1266 1267 1268 1269 1270 1271
- LCD Support:	CONFIG_LCD

		Define this to enable LCD support (for output to LCD
		display); also select one of the supported displays
		by defining one of these:

Stelian Pop's avatar
Stelian Pop committed
1272 1273 1274 1275
		CONFIG_ATMEL_LCD:

			HITACHI TX09D70VM1CCA, 3.5", 240x320.

wdenk's avatar
wdenk committed
1276
		CONFIG_NEC_NL6448AC33:
wdenk's avatar
wdenk committed
1277

wdenk's avatar
wdenk committed
1278
			NEC NL6448AC33-18. Active, color, single scan.
wdenk's avatar
wdenk committed
1279

wdenk's avatar
wdenk committed
1280
		CONFIG_NEC_NL6448BC20
wdenk's avatar
wdenk committed
1281

wdenk's avatar
wdenk committed
1282 1283 1284 1285 1286 1287
			NEC NL6448BC20-08. 6.5", 640x480.
			Active, color, single scan.

		CONFIG_NEC_NL6448BC33_54

			NEC NL6448BC33-54. 10.4", 640x480.
wdenk's avatar
wdenk committed
1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314
			Active, color, single scan.

		CONFIG_SHARP_16x9

			Sharp 320x240. Active, color, single scan.
			It isn't 16x9, and I am not sure what it is.

		CONFIG_SHARP_LQ64D341

			Sharp LQ64D341 display, 640x480.
			Active, color, single scan.

		CONFIG_HLD1045

			HLD1045 display, 640x480.
			Active, color, single scan.

		CONFIG_OPTREX_BW

			Optrex	 CBL50840-2 NF-FW 99 22 M5
			or
			Hitachi	 LMG6912RPFC-00T
			or
			Hitachi	 SP14Q002

			320x240. Black & white.

1315 1316
		CONFIG_LCD_ALIGNMENT

1317
		Normally the LCD is page-aligned (typically 4KB). If this is
1318 1319 1320 1321 1322 1323
		defined then the LCD will be aligned to this value instead.
		For ARM it is sometimes useful to use MMU_SECTION_SIZE
		here, since it is cheaper to change data cache settings on
		a per-section basis.


1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343
		CONFIG_LCD_ROTATION

		Sometimes, for example if the display is mounted in portrait
		mode or even if it's mounted landscape but rotated by 180degree,
		we need to rotate our content of the display relative to the
		framebuffer, so that user can read the messages which are
		printed out.
		Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
		initialized with a given rotation from "vl_rot" out of
		"vidinfo_t" which is provided by the board specific code.
		The value for vl_rot is coded as following (matching to
		fbcon=rotate:<n> linux-kernel commandline):
		0 = no rotation respectively 0 degree
		1 = 90 degree rotation
		2 = 180 degree rotation
		3 = 270 degree rotation

		If CONFIG_LCD_ROTATION is not defined, the console will be
		initialized with 0degree rotation.

1344 1345 1346 1347
		CONFIG_LCD_BMP_RLE8

		Support drawing of RLE8-compressed bitmaps on the LCD.

1348 1349 1350 1351 1352
		CONFIG_I2C_EDID

		Enables an 'i2c edid' command which can read EDID
		information over I2C from an attached LCD display.

wdenk's avatar
wdenk committed
1353
- Splash Screen Support: CONFIG_SPLASH_SCREEN
1354

wdenk's avatar
wdenk committed
1355 1356 1357
		If this option is set, the environment is checked for
		a variable "splashimage". If found, the usual display
		of logo, copyright and system information on the LCD
1358
		is suppressed and the BMP image at the address
wdenk's avatar
wdenk committed
1359 1360 1361 1362
		specified in "splashimage" is loaded instead. The
		console is redirected to the "nulldev", too. This
		allows for a "silent" boot where a splash screen is
		loaded very quickly after power-on.
1363

1364 1365 1366 1367
		CONFIG_SPLASHIMAGE_GUARD

		If this option is set, then U-Boot will prevent the environment
		variable "splashimage" from being set to a problematic address
1368
		(see doc/README.displaying-bmps).
1369 1370 1371 1372 1373 1374
		This option is useful for targets where, due to alignment
		restrictions, an improperly aligned BMP image will cause a data
		abort. If you think you will not have problems with unaligned
		accesses (for example because your toolchain prevents them)
		there is no need to set this option.

1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394
		CONFIG_SPLASH_SCREEN_ALIGN

		If this option is set the splash image can be freely positioned
		on the screen. Environment variable "splashpos" specifies the
		position as "x,y". If a positive number is given it is used as
		number of pixel from left/top. If a negative number is given it
		is used as number of pixel from right/bottom. You can also
		specify 'm' for centering the image.

		Example:
		setenv splashpos m,m
			=> image at center of screen

		setenv splashpos 30,20
			=> image at x = 30 and y = 20

		setenv splashpos -10,m
			=> vertically centered image
			   at x = dspWidth - bmpWidth - 9

1395 1396 1397 1398 1399 1400
- Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP

		If this option is set, additionally to standard BMP
		images, gzipped BMP images can be displayed via the
		splashscreen support or the bmp command.

1401 1402 1403 1404 1405 1406
- Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8

		If this option is set, 8-bit RLE compressed BMP images
		can be displayed via the splashscreen support or the
		bmp command.

wdenk's avatar
wdenk committed
1407
- Compression support:
1408 1409 1410 1411
		CONFIG_GZIP

		Enabled by default to support gzip compressed images.

wdenk's avatar
wdenk committed
1412 1413 1414 1415 1416 1417
		CONFIG_BZIP2

		If this option is set, support for bzip2 compressed
		images is included. If not, only uncompressed and gzip
		compressed images are supported.

1418
		NOTE: the bzip2 algorithm requires a lot of RAM, so
1419
		the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1420
		be at least 4MB.
1421

wdenk's avatar
wdenk committed
1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438
- MII/PHY support:
		CONFIG_PHY_CLOCK_FREQ (ppc4xx)

		The clock frequency of the MII bus

		CONFIG_PHY_RESET_DELAY

		Some PHY like Intel LXT971A need extra delay after
		reset before any MII register access is possible.
		For such PHY, set this option to the usec delay
		required. (minimum 300usec for LXT971A)

		CONFIG_PHY_CMD_DELAY (ppc4xx)

		Some PHY like Intel LXT971A need extra delay after
		command issued before MII status register can be read

wdenk's avatar
wdenk committed
1439 1440 1441 1442
- IP address:
		CONFIG_IPADDR

		Define a default value for the IP address to use for
1443
		the default Ethernet interface, in case this is not
wdenk's avatar
wdenk committed
1444
		determined through e.g. bootp.
1445
		(Environment variable "ipaddr")
wdenk's avatar
wdenk committed
1446 1447 1448 1449

- Server IP address:
		CONFIG_SERVERIP

1450
		Defines a default value for the IP address of a TFTP
wdenk's avatar
wdenk committed
1451
		server to contact when using the "tftboot" command.
1452
		(Environment variable "serverip")
wdenk's avatar
wdenk committed
1453

1454 1455 1456 1457 1458
		CONFIG_KEEP_SERVERADDR

		Keeps the server's MAC address, in the env 'serveraddr'
		for passing to bootargs (like Linux's netconsole option)

1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475
- Gateway IP address:
		CONFIG_GATEWAYIP

		Defines a default value for the IP address of the
		default router where packets to other networks are
		sent to.
		(Environment variable "gatewayip")

- Subnet mask:
		CONFIG_NETMASK

		Defines a default value for the subnet mask (or
		routing prefix) which is used to determine if an IP
		address belongs to the local subnet or needs to be
		forwarded through a router.
		(Environment variable "netmask")

David Updegraff's avatar
David Updegraff committed
1476 1477 1478 1479 1480
- Multicast TFTP Mode:
		CONFIG_MCAST_TFTP

		Defines whether you want to support multicast TFTP as per
		rfc-2090; for example to work with atftp.  Lets lots of targets
1481
		tftp down the same boot image concurrently.  Note: the Ethernet
David Updegraff's avatar
David Updegraff committed
1482 1483 1484
		driver in use must provide a function: mcast() to join/leave a
		multicast group.

wdenk's avatar
wdenk committed
1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495
- BOOTP Recovery Mode:
		CONFIG_BOOTP_RANDOM_DELAY

		If you have many targets in a network that try to
		boot using BOOTP, you may want to avoid that all
		systems send out BOOTP requests at precisely the same
		moment (which would happen for instance at recovery
		from a power failure, when all systems will try to
		boot, thus flooding the BOOTP server. Defining
		CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
		inserted before sending out BOOTP requests. The
1496
		following delays are inserted then:
wdenk's avatar
wdenk committed
1497 1498 1499 1500 1501 1502 1503

		1st BOOTP request:	delay 0 ... 1 sec
		2nd BOOTP request:	delay 0 ... 2 sec
		3rd BOOTP request:	delay 0 ... 4 sec
		4th and following
		BOOTP requests:		delay 0 ... 8 sec

1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521
		CONFIG_BOOTP_ID_CACHE_SIZE

		BOOTP packets are uniquely identified using a 32-bit ID. The
		server will copy the ID from client requests to responses and
		U-Boot will use this to determine if it is the destination of
		an incoming response. Some servers will check that addresses
		aren't in use before handing them out (usually using an ARP
		ping) and therefore take up to a few hundred milliseconds to
		respond. Network congestion may also influence the time it
		takes for a response to make it back to the client. If that
		time is too long, U-Boot will retransmit requests. In order
		to allow earlier responses to still be accepted after these
		retransmissions, U-Boot's BOOTP client keeps a small cache of
		IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
		cache. The default is to keep IDs for up to four outstanding
		requests. Increasing this will allow U-Boot to accept offers
		from a BOOTP client in networks with unusually high latency.

1522
- DHCP Advanced Options:
1523 1524 1525 1526 1527 1528 1529 1530 1531
		You can fine tune the DHCP functionality by defining
		CONFIG_BOOTP_* symbols:

		CONFIG_BOOTP_NISDOMAIN
		CONFIG_BOOTP_BOOTFILESIZE
		CONFIG_BOOTP_SEND_HOSTNAME
		CONFIG_BOOTP_NTPSERVER
		CONFIG_BOOTP_TIMEOFFSET
		CONFIG_BOOTP_VENDOREX
1532
		CONFIG_BOOTP_MAY_FAIL
1533

1534 1535
		CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
		environment variable, not the BOOTP server.
1536

1537 1538 1539 1540 1541 1542
		CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
		after the configured retry count, the call will fail
		instead of starting over.  This can be used to fail over
		to Link-local IP address configuration if the DHCP server
		is not available.

1543 1544 1545
		CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
		to do a dynamic update of a DNS server. To do this, they
		need the hostname of the DHCP requester.
1546
		If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1547 1548
		of the "hostname" environment variable is passed as
		option 12 to the DHCP server.
1549

1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563
		CONFIG_BOOTP_DHCP_REQUEST_DELAY

		A 32bit value in microseconds for a delay between
		receiving a "DHCP Offer" and sending the "DHCP Request".
		This fixes a problem with certain DHCP servers that don't
		respond 100% of the time to a "DHCP request". E.g. On an
		AT91RM9200 processor running at 180MHz, this delay needed
		to be *at least* 15,000 usec before a Windows Server 2003
		DHCP server would reply 100% of the time. I recommend at
		least 50,000 usec to be safe. The alternative is to hope
		that one of the retries will be successful but note that
		the DHCP timeout and retry process takes a longer than
		this delay.

1564 1565 1566 1567 1568 1569 1570 1571
 - Link-local IP address negotiation:
		Negotiate with other link-local clients on the local network
		for an address that doesn't require explicit configuration.
		This is especially useful if a DHCP server cannot be guaranteed
		to exist in all environments that the device must operate.

		See doc/README.link-local for more information.

1572 1573 1574 1575 1576 1577 1578 1579 1580
 - MAC address from environment variables

		FDT_SEQ_MACADDR_FROM_ENV

		Fix-up device tree with MAC addresses fetched sequentially from
		environment variables. This config work on assumption that
		non-usable ethernet node of device-tree are either not present
		or their status has been marked as "disabled".

1581
 - CDP Options:
wdenk's avatar
wdenk committed
1582
		CONFIG_CDP_DEVICE_ID
1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594

		The device id used in CDP trigger frames.

		CONFIG_CDP_DEVICE_ID_PREFIX

		A two character string which is prefixed to the MAC address
		of the device.

		CONFIG_CDP_PORT_ID

		A printf format string which contains the ascii name of
		the port. Normally is set to "eth%d" which sets
1595
		eth0 for the first Ethernet, eth1 for the second etc.
1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622

		CONFIG_CDP_CAPABILITIES

		A 32bit integer which indicates the device capabilities;
		0x00000010 for a normal host which does not forwards.

		CONFIG_CDP_VERSION

		An ascii string containing the version of the software.

		CONFIG_CDP_PLATFORM

		An ascii string containing the name of the platform.

		CONFIG_CDP_TRIGGER

		A 32bit integer sent on the trigger.

		CONFIG_CDP_POWER_CONSUMPTION

		A 16bit integer containing the power consumption of the
		device in .1 of milliwatts.

		CONFIG_CDP_APPLIANCE_VLAN_TYPE

		A byte containing the id of the VLAN.

1623
- Status LED:	CONFIG_LED_STATUS
wdenk's avatar
wdenk committed
1624 1625 1626 1627 1628 1629 1630

		Several configurations allow to display the current
		status using a LED. For instance, the LED will blink
		fast while running U-Boot code, stop blinking as
		soon as a reply to a BOOTP request was received, and
		start blinking slow once the Linux kernel is running
		(supported by a status LED driver in the Linux
1631
		kernel). Defining CONFIG_LED_STATUS enables this
wdenk's avatar
wdenk committed
1632 1633
		feature in U-Boot.

1634 1635
		Additional options:

1636
		CONFIG_LED_STATUS_GPIO
1637 1638
		The status LED can be connected to a GPIO pin.
		In such cases, the gpio_led driver can be used as a
1639
		status LED backend implementation. Define CONFIG_LED_STATUS_GPIO
1640 1641
		to include the gpio_led driver in the U-Boot binary.

1642 1643 1644 1645 1646 1647 1648
		CONFIG_GPIO_LED_INVERTED_TABLE
		Some GPIO connected LEDs may have inverted polarity in which
		case the GPIO high value corresponds to LED off state and
		GPIO low value corresponds to LED on state.
		In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
		with a list of GPIO LEDs that have inverted polarity.

1649 1650 1651 1652 1653 1654 1655 1656 1657 1658
- I2C Support:	CONFIG_SYS_I2C

		This enable the NEW i2c subsystem, and will allow you to use
		i2c commands at the u-boot command line (as long as you set
		CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
		based realtime clock chips or other i2c devices. See
		common/cmd_i2c.c for a description of the command line
		interface.

		ported i2c driver to the new framework:
1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671
		- drivers/i2c/soft_i2c.c:
		  - activate first bus with CONFIG_SYS_I2C_SOFT define
		    CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
		    for defining speed and slave address
		  - activate second bus with I2C_SOFT_DECLARATIONS2 define
		    CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
		    for defining speed and slave address
		  - activate third bus with I2C_SOFT_DECLARATIONS3 define
		    CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
		    for defining speed and slave address
		  - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
		    CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
		    for defining speed and slave address
1672

1673 1674 1675 1676 1677 1678
		- drivers/i2c/fsl_i2c.c: