Commit 2d0c3d6b authored by Andre Przywara's avatar Andre Przywara Committed by Jagan Teki

sunxi: DT: H3: update board .dts files from Linux

Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Mon Jun 11 17:57:38 2018 -0700

    Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.
Signed-off-by: default avatarAndre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard's avatarMaxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki's avatarJagan Teki <jagan@amarulasolutions.com>
parent 1caeae37
......@@ -49,7 +49,6 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero";
......@@ -58,6 +57,7 @@
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet0 = &emac;
ethernet1 = &xr819;
};
......@@ -92,9 +92,14 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <200>;
};
};
&ehci0 {
status = "okay";
};
&ehci1 {
status = "okay";
};
......@@ -109,8 +114,7 @@
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
......@@ -130,17 +134,56 @@
};
};
&ohci0 {
status = "okay";
};
&ohci1 {
status = "okay";
};
&spi0 {
/* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
status = "disabled";
flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mxicy,mx25l1606e", "winbond,w25q128";
reg = <0>;
spi-max-frequency = <40000000>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&usb_otg {
dr_mode = "peripheral";
status = "okay";
};
&usbphy {
/* USB VBUS is always on */
/*
* USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
* power up the board; when it's used as OTG port, this VBUS is
* always off even if the board is powered via GPIO pins.
*/
status = "okay";
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
};
......@@ -46,13 +46,13 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Banana Pi BPI-M2-Plus";
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
aliases {
ethernet0 = &emac;
serial0 = &uart0;
serial1 = &uart1;
};
......@@ -61,10 +61,20 @@
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pwr_led_bpi_m2p>;
pwr_led {
label = "bananapi-m2-plus:red:pwr";
......@@ -76,7 +86,6 @@
gpio_keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&sw_r_bpi_m2p>;
sw4 {
label = "power";
......@@ -85,14 +94,27 @@
};
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&wifi_en_bpi_m2p>;
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
......@@ -105,6 +127,33 @@
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <&reg_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
status = "okay";
};
&external_mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0>;
};
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
......@@ -114,8 +163,7 @@
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
......@@ -127,7 +175,7 @@
non-removable;
status = "okay";
brcmf: bcrmf@1 {
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
......@@ -158,27 +206,9 @@
status = "okay";
};
&r_pio {
pwr_led_bpi_m2p: led_pins@0 {
allwinner,pins = "PL10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
sw_r_bpi_m2p: key_pins@0 {
allwinner,pins = "PL3";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
wifi_en_bpi_m2p: wifi_en_pin {
allwinner,pins = "PL7";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
&reg_usb0_vbus {
gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
status = "okay";
};
&uart0 {
......@@ -199,6 +229,8 @@
};
&usbphy {
/* USB VBUS is on as long as VCC-IO is on */
usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
usb0_vbus-supply = <&reg_usb0_vbus>;
/* USB host VBUS is on as long as VCC-IO is on */
status = "okay";
};
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
*
* SPDX-License-Identifier: (GPL-2.0+ OR MIT)
*/
/dts-v1/;
......
......@@ -45,6 +45,28 @@
/ {
model = "FriendlyArm NanoPi M1 Plus";
compatible = "friendlyarm,nanopi-m1-plus", "allwinner,sun8i-h3";
aliases {
serial1 = &uart3;
ethernet0 = &emac;
ethernet1 = &sdio_wifi;
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
regulator-name = "gmac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
startup-delay-us = <100000>;
enable-active-high;
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
&ehci1 {
......@@ -55,6 +77,56 @@
status = "okay";
};
&emac {
pinctrl-names = "default";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <&reg_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
phy-mode = "rgmii";
status = "okay";
};
&external_mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <7>;
};
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
sdio_wifi: sdio_wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
interrupt-names = "host-wake";
};
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
bus-width = <8>;
non-removable;
status = "okay";
};
&ohci1 {
status = "okay";
};
......@@ -62,3 +134,9 @@
&ohci2 {
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
status = "okay";
};
......@@ -45,6 +45,25 @@
/ {
model = "FriendlyArm NanoPi M1";
compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
aliases {
ethernet0 = &emac;
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
};
&de {
status = "okay";
};
&ehci1 {
......@@ -55,6 +74,29 @@
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
status = "okay";
};
&ohci1 {
status = "okay";
};
......
......@@ -45,7 +45,6 @@
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "FriendlyARM NanoPi NEO Air";
......@@ -73,16 +72,37 @@
gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
};
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
};
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
&mmc1 {
vmmc-supply = <&reg_vcc3v3>;
vqmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
interrupt-names = "host-wake";
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
......
......@@ -47,9 +47,26 @@
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
};
&ehci0 {
status = "okay";
};
&emac {
phy-handle = <&int_mii_phy>;
phy-mode = "mii";
allwinner,leds-active-low;
status = "okay";
};
&ohci0 {
status = "okay";
};
&usb_otg {
status = "okay";
dr_mode = "peripheral";
};
&usbphy {
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
};
......@@ -81,7 +81,7 @@
pinctrl-names = "default";
pinctrl-0 = <&sw_r_npi>;
k1@0 {
k1 {
label = "k1";
linux,code = <KEY_POWER>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
......@@ -95,8 +95,7 @@
&mmc0 {
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
cd-inverted;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
status = "okay";
vmmc-supply = <&reg_vcc3v3>;
};
......@@ -106,19 +105,19 @@
};
&pio {
leds_npi: led_pins@0 {
leds_npi: led_pins {
pins = "PA10";
function = "gpio_out";
};
};
&r_pio {
leds_r_npi: led_pins@0 {
leds_r_npi: led_pins {
pins = "PL10";
function = "gpio_out";
};
sw_r_npi: key_pins@0 {
sw_r_npi: key_pins {
pins = "PL3";
function = "gpio_in";
};
......
......@@ -46,7 +46,6 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi 2";
......@@ -63,6 +62,17 @@
stdout-path = "serial0:115200n8";
};
connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_in: endpoint {
remote-endpoint = <&hdmi_out_con>;
};
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
......@@ -106,6 +116,19 @@
};
};
&codec {
allwinner,pa-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
allwinner,audio-routing =
"Speaker", "LINEOUT",
"MIC1", "Mic",
"Mic", "MBIAS";
status = "okay";
};
&de {
status = "okay";
};
&ehci1 {
status = "okay";
};
......@@ -117,6 +140,16 @@
status = "okay";
};
&hdmi {
status = "okay";
};
&hdmi_out {
hdmi_out_con: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
......@@ -126,8 +159,7 @@
&mmc0 {
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
......@@ -148,34 +180,26 @@
};
&pio {
leds_opc: led_pins@0 {
allwinner,pins = "PA15";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
leds_opc: led_pins {
pins = "PA15";
function = "gpio_out";
};
};
&r_pio {
leds_r_opc: led_pins@0 {
allwinner,pins = "PL10";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
leds_r_opc: led_pins {
pins = "PL10";
function = "gpio_out";
};
sw_r_opc: key_pins@0 {
allwinner,pins = "PL3", "PL4";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
sw_r_opc: key_pins {
pins = "PL3", "PL4";
function = "gpio_in";
};
wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin@0 {