Commit 1bad5e14 authored by Manivannan Sadhasivam's avatar Manivannan Sadhasivam Committed by Philipp Tomsich

rockchip: rk3399: Add common Rock960 family from Vamrs

Rock960 is a family of boards based on Rockchip RK3399 SoC from Vamrs.
It consists of Rock960 (Consumer Edition) and Ficus (Enterprise Edition)
96Boards.

Below are some of the key differences between both Rock960 and Ficus
boards:

1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960

The common board support will be utilized by both boards. The device
tree has been organized in such a way that only the properties which
differ between both boards are placed in the board specific dts and
the reset of the nodes are placed in common dtsi file.
Signed-off-by: 's avatarManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[Added instructions for SD card boot]
Signed-off-by: 's avatarEzequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Simon Glass's avatarSimon Glass <sjg@chromium.org>
Tested-by: 's avatarPeter Robinson <pbrobinson@gmail.com>
parent 2c9050cd
This diff is collapsed.
......@@ -28,6 +28,31 @@ config TARGET_PUMA_RK3399
* HDMI, eDP, MIPI-DSI, MIPI-DSI/CSI and MIPI-CSI
* SPI, I2C, I2S, UART, GPIO, ...
config TARGET_ROCK960_RK3399
bool "Vamrs Limited Rock960 board family"
help
Support for Rock960 board family by Vamrs Limited. This board
family consists of Rock960 (Consumer Edition) and Ficus
(Enterprise Edition) 96Boards.
Common features implemented on both boards:
* Rockchip RK3399 SoC (2xCortex A72, 4xCortex A53, ARM Mali T860MP4)
* 16/32GB eMMC, uSD slot
* HDMI/DP/MIPI
* 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
Additional features of Rock960:
* 2GiB/4GiB LPDDR3 RAM
* 1x USB 3.0 type A, 1x USB 2.0 type A (host mode only),
1x USB 3.0 type C OTG
Additional features of Ficus:
* 2GiB/4GiB DDR3 RAM
* Ethernet
* Dual SATA
* 2x USB 3.0 type A, 2x USB 2.0 type A (host mode only),
1x USB 3.0 type C OTG
endchoice
config SYS_SOC
......@@ -38,5 +63,6 @@ config SYS_MALLOC_F_LEN
source "board/rockchip/evb_rk3399/Kconfig"
source "board/theobroma-systems/puma_rk3399/Kconfig"
source "board/vamrs/rock960_rk3399/Kconfig"
endif
if TARGET_ROCK960_RK3399
config SYS_BOARD
default "rock960_rk3399"
config SYS_VENDOR
default "vamrs"
config SYS_CONFIG_NAME
default "rock960_rk3399"
config BOARD_SPECIFIC_OPTIONS # dummy
def_bool y
endif
ROCK960-RK3399
M: Manivannan Sadhasivam manivannan.sadhasivam@linaro.org
S: Maintained
F: board/rockchip/rock960_rk3399
F: include/configs/rock960_rk3399.h
F: configs/rock960-rk3399_defconfig
# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
#
obj-y += rock960-rk3399.o
Contents
========
1. Introduction
2. Get the Source and prebuild binary
3. Compile the U-Boot
4. Compile the rkdeveloptool
5. Package the image
5.1. Package the image for U-Boot SPL(option 1)
5.2. Package the image for Rockchip miniloader(option 2)
6. Bootloader storage options
7. Flash the image to eMMC
7.1. Flash the image with U-Boot SPL(option 1)
7.2. Flash the image with Rockchip miniloader(option 2)
8. Create a bootable SD/MMC
9. And that is it
Introduction
============
Rock960 board family consists of Rock960 (Consumer Edition) and
Ficus (Enterprise Edition) 96Boards featuring Rockchip RK3399 SoC.
Common features implemented on both boards:
* CPU: ARMv8 64bit Big-Little architecture,
* Big: dual-core Cortex-A72
* Little: quad-core Cortex-A53
* IRAM: 200KB
* eMMC: 16/32GB eMMC 5.1
* PMU: RK808
* SD/MMC
* Display: HDMI/DP/MIPI
* Low Speed Expansion Connector
* High Speed Expansion Connector
Additional features of Rock960:
* DRAM: 2GB/4GB LPDDR3 @ 1866MHz
* 1x USB 3.0 type A, 1x USB 2.0 type A (host mode only),
1x USB 3.0 type C OTG
Additional features of Ficus:
* DRAM: 2GB/4GB DDR3 @ 1600MHz
* Ethernet
* 2x USB 3.0 type A, 2x USB 2.0 type A (host mode only),
1x USB 3.0 type C OTG
Here is the step-by-step to boot to U-Boot on Rock960 boards.
Get the Source and prebuild binary
==================================
> git clone https://github.com/96rocks/rkbin.git
> git clone https://github.com/rockchip-linux/rkdeveloptool.git
Compile the U-Boot
==================
> cd ../u-boot
> cp ../rkbin/rk33/rk3399_bl31_v1.00.elf ./bl31.elf
> export ARCH=arm64
> export CROSS_COMPILE=aarch64-linux-gnu-
> make rock960-rk3399_defconfig
> make
> make u-boot.itb
Compile the rkdeveloptool
=========================
Follow instructions in latest README
> cd ../rkdeveloptool
> autoreconf -i
> ./configure
> make
> sudo make install
Package the image
=================
Package the image for U-Boot SPL(option 1)
--------------------------------
> cd ..
> tools/mkimage -n rk3399 -T rksd -d spl/u-boot-spl.bin idbspl.img
Get idbspl.img in this step.
Package the image for Rockchip miniloader(option 2)
------------------------------------------
> cd ../rkbin
> ./tools/loaderimage --pack --uboot u-boot/u-boot-dtb.bin uboot.img 0x200000
> ../u-boot/tools/mkimage -n rk3399 -T rksd -d rk3399_ddr_933MHz_v1.08.bin idbloader.img
> cat ./rk33/rk3399_miniloader_v1.06.bin >> idbloader.img
Get uboot.img and idbloader.img in this step.
Bootloader storage options
==========================
There are a few different storage options for the bootloader.
This document explores two of these: eMMC and removable SD/MMC.
Flash the image to eMMC
=======================
Flash the image with U-Boot SPL(option 1)
-------------------------------
Power on(or reset with RESET KEY) with MASKROM KEY preesed, and then:
> rkdeveloptool db rkbin/rk33/rk3399_loader_v1.08.106.bin
> rkdeveloptool wl 64 u-boot/idbspl.img
> rkdeveloptool wl 0x4000 u-boot/u-boot.itb
> rkdeveloptool rd
Flash the image with Rockchip miniloader(option 2)
----------------------------------------
Power on(or reset with RESET KEY) with MASKROM KEY preesed, and then:
> rkdeveloptool db rkbin/rk33/rk3399_loader_v1.08.106.bin
> rkdeveloptool wl 0x40 idbloader.img
> rkdeveloptool wl 0x4000 uboot.img
> rkdeveloptool wl 0x6000 ./img/rk3399/trust.img
> rkdeveloptool rd
Create a bootable SD/MMC
========================
The idbspl.img contains the first stage, and the u-boot.img the second stage.
As explained in the Rockchip partition table reference [1], the first stage
(aka loader1) start sector is 64, and the second stage start sector is 16384.
Each sector is 512 bytes, which means the first stage offset is 32 KiB,
and the second stage offset is 8 MiB.
Note: the second stage location is actually not as per the spec,
but defined by the SPL. Mainline SPL defines an 8 MiB offset for the second
stage.
Assuming the SD card is exposed by device /dev/mmcblk0, the commands
to write the two stages are:
> dd if=idbspl.img of=/dev/mmcblk0 bs=1k seek=32
> dd if=u-boot.itb of=/dev/mmcblk0 bs=1k seek=8192
Setting up the kernel and rootfs is beyond the scope of this document.
And that is it
==============
You should be able to get U-Boot log in console/UART2(baurdrate 1500000)
For more detail, please reference [2].
[1] http://opensource.rock-chips.com/wiki_Partitions
[2] http://opensource.rock-chips.com/wiki_Boot_option
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
*/
#include <common.h>
#include <dm.h>
#include <dm/pinctrl.h>
#include <dm/uclass-internal.h>
#include <asm/arch/periph.h>
#include <power/regulator.h>
#include <spl.h>
int board_init(void)
{
int ret;
ret = regulators_enable_boot_on(false);
if (ret)
debug("%s: Cannot enable boot on regulator\n", __func__);
return 0;
}
void spl_board_init(void)
{
struct udevice *pinctrl;
int ret;
ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
if (ret) {
debug("%s: Cannot find pinctrl device\n", __func__);
goto err;
}
/* Enable debug UART */
ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_UART_DBG);
if (ret) {
debug("%s: Failed to set up console UART\n", __func__);
goto err;
}
preloader_console_init();
return;
err:
printf("%s: Error %d\n", __func__, ret);
/* No way to report error here */
hang();
}
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
*/
#ifndef __ROCK960_RK3399_H
#define __ROCK960_RK3399_H
#include <configs/rk3399_common.h>
#define CONFIG_SYS_MMC_ENV_DEV 1
#define SDRAM_BANK_SIZE (2UL << 30)
#endif
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment